Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
#41
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
>William Oliveri did pass the time by typing:
>> How do you erase the trouble codes?
>
>Disconnect the battery for about 20-30 min
>and that will cause it to dump everything.
Usually, 20-30 seconds will erase trouble codes.
>
>That also resets the tranny computer and other
>things. For the first few dozen miles you run
>after doing this drive "normally". i.e. don't
>mash the gas, the computer will be fine tuning
>the mix and other things.
The computer is constantly "fine tuning" and updating the adaptive memory. The
best thing to do is to drive it like you drive, and it will adapt to it.
>PS. This is exactly what you have to do if you
>ever replace the header, injectors, or O2 sensor.
>Otherwise the computer can become confused.
The only time the computer gets confused is if it's getting false information,
as it would from a bad sensor. Replacing the sensor is all that is needed, and
the computer will automatically correct for it. The only thing you do when
resetting the computer is change where the computer starts to adjust from, not
where it will end up. It will always adjust. That's it's job.
>William Oliveri did pass the time by typing:
>> How do you erase the trouble codes?
>
>Disconnect the battery for about 20-30 min
>and that will cause it to dump everything.
Usually, 20-30 seconds will erase trouble codes.
>
>That also resets the tranny computer and other
>things. For the first few dozen miles you run
>after doing this drive "normally". i.e. don't
>mash the gas, the computer will be fine tuning
>the mix and other things.
The computer is constantly "fine tuning" and updating the adaptive memory. The
best thing to do is to drive it like you drive, and it will adapt to it.
>PS. This is exactly what you have to do if you
>ever replace the header, injectors, or O2 sensor.
>Otherwise the computer can become confused.
The only time the computer gets confused is if it's getting false information,
as it would from a bad sensor. Replacing the sensor is all that is needed, and
the computer will automatically correct for it. The only thing you do when
resetting the computer is change where the computer starts to adjust from, not
where it will end up. It will always adjust. That's it's job.
#42
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
Yeah, took the plugs out, let them set for a couple of hours while I did
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
#43
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
Yeah, took the plugs out, let them set for a couple of hours while I did
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
#44
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
Yeah, took the plugs out, let them set for a couple of hours while I did
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
#45
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
Yeah, took the plugs out, let them set for a couple of hours while I did
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
something else also allowing the cylinders to breath. Came back and cleaned
the off with a wire brush. Then took another look at the distributor to
make sure I put the rotor back on (was thinking about this when I was doing
other things). I was hoping it was off which would explain why it wouldn't
start but it was there in place.
I'm trying to think of something else I might have done in the process but
everything looks correct.
hmmmmmmm.....
Bill
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A79563.3A3E15D@sympatico.ca...
> I would guess that you have flooded the plugs.
>
> Sometimes they need to be removed to dry out before it will run again.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> William Oliveri wrote:
> >
> > Well, I took the dist off and lifted up the plate and looked at the
sensor
> > and it was caked with black crap so I cleaned it all off and put it all
back
> > together again. Also, don't know how it got there but I stuck a straw
into
> > the wiring harness connector (3 pin) and found what looked to be oil.
So I
> > cleaned that up too.
> >
> > Now it still won't start and there's no fault code indicating a problem.
> >
> > That is I don't have 54 anymore I just have the following returns:
> >
> > 12
> > 55
> >
> > Any ideas?
> >
> > Thanks,
> >
> > Bill
> >
> > "DougW" <post.replies@invalid.address> wrote in message
> > news:MyBpc.50671$Z%5.32467@okepread01...
> > > William Oliveri did pass the time by typing:
> > > > Whoops... The site I got the code below was from a YJ site.
> > > >
> > > > http://www.jedi.com/obiwan/jeep/dtc.html
> > > >
> > > >
> > > > I now have found a MPI Kit site (don't know why Hesco doesn't have
these
> > on
> > > > their site)
> > > >
> > > > http://www.sierrajeep.com/trouble.htm
> > > >
> > > > which says:
> > > >
> > > > 54 = Distributor sync pickup
> > > >
> > > > Now, what does this mean? Distributor bad? Can it be fixed?
> > >
> > > That would be this.
> > > http://members.***.net/wilsond/stator/
> > >
> > > It can be replaced, just follow the distributor removal
> > > procecure back on the main page. You have to remove the
> > > pin holding the distributor gear in and pull the shaft to
> > > get to the stator.
> > >
> > > But first.... clean the connector just in case that is the problem.
> > >
> > > --
> > > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > > Banks Header - and BEER, in the fridge!
> > >
> > >
#46
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
bllsht did pass the time by typing:
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
#47
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
bllsht did pass the time by typing:
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
#48
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
bllsht did pass the time by typing:
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
#49
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
bllsht did pass the time by typing:
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
> In message <swKpc.51828$Z%5.42021@okepread01>, "DougW" wrote:
> The only time the computer gets confused is if it's getting false information,
> as it would from a bad sensor. Replacing the sensor is all that is needed,
> and the computer will automatically correct for it. The only thing you do
> when resetting the computer is change where the computer starts to adjust
> from, not where it will end up. It will always adjust. That's it's job.
Correct, but it's easier and quicker for the computer to adjust from a fresh
start than to un-learn/re-learn a new setup.
--
DougW
#50
Guest
Posts: n/a
Re: Changing the name of my jeep from Blackie to Black Cloud (or error 54 diagnostic code)
William Oliveri did pass the time by typing:
> Yeah, took the plugs out, let them set for a couple of hours while I did
> something else also allowing the cylinders to breath. Came back and cleaned
> the off with a wire brush. Then took another look at the distributor to
> make sure I put the rotor back on (was thinking about this when I was doing
> other things). I was hoping it was off which would explain why it wouldn't
> start but it was there in place.
>
> I'm trying to think of something else I might have done in the process but
> everything looks correct.
>
>
> hmmmmmmm.....
coil primary?
CPS sensor connection back by the dipstick?
--
DougW
> Yeah, took the plugs out, let them set for a couple of hours while I did
> something else also allowing the cylinders to breath. Came back and cleaned
> the off with a wire brush. Then took another look at the distributor to
> make sure I put the rotor back on (was thinking about this when I was doing
> other things). I was hoping it was off which would explain why it wouldn't
> start but it was there in place.
>
> I'm trying to think of something else I might have done in the process but
> everything looks correct.
>
>
> hmmmmmmm.....
coil primary?
CPS sensor connection back by the dipstick?
--
DougW