Carter 2bbl specs
#51
Guest
Posts: n/a
Re: Carter 2bbl specs-- update / fixed
The BBD kit has gaskets for both the electric model and the standard
model in it which makes it confusing right off the bat.
They have a sneaky base plate add on too. The sucker has 4 little
notches in it that have to be on the top side and not covered by a
gasket or the carb won't get vacuum to it's ports.
Mike
Earle Horton wrote:
>
> I have seen this happen a lot. It is almost as if the designers wanted the
> carburetor to "almost work" with a gasket in wrong. Sometimes, they put
> extra gaskets in carburetor rebuild kits, that apparently don't fit any
> model carburetor ever made. I don't know how many shade tree mechanics and
> professional mechanics too have been caught by this little joke. Let's just
> say that I found out about it the hard way too.
>
> Earle
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:443D14B4.4DD1B29@sympatico.ca...
> > Cool.
> >
> > Mike
> >
> > JohanB wrote:
> > >
> > > Hey....
> > >
> > > Took the idle tubes out like you suggested.
> > > They were clean
> > > double checked everything and found that the idiot that "overhauled " it
> > > before swapped the gaskets.
> > > He put the lower gasket between the idle tube cover and the idle tube
> gasket
> > > under the venturi cluster causing it to leave a little gap between the
> idle
> > > tube cover and venturi cluster where the gas dripped out.
> > >
> > > Off course the last idiot that worked on it just peeled the old gaskets
> off
> > > and also put the new 1's in wrong
> > > ( oh wait , that was me...... :-) )
> > >
> > > after starting it and cleaning the gas out off the manifold I started it
> > > again after an hour and it fired right up
> > >
> > > Thanks yall for the tips
> > >
> > > "Mike Romain" <romainm@sympatico.ca> wrote in message
> > > news:443A6531.9C0108CB@sympatico.ca...
> > > > I have had the exact same trouble with the last kit I put in. The
> float
> > > > needle and seat were bad. The store warrantied them.
> > > >
> > > > The idle tubes are those two long brass tubes that hang down. They
> are
> > > > real sneaky for plugging up. I can just remove the choke plate and
> then
> > > > the two screws holding the venturi in and lift and twist the venturi
> > > > around so it slips out without removing the whole top of the carb for
> > > > cleaning. You have to blow through the tubes to make sure they are
> > > > clear. The tubes 'can' fall out too.
> > > >
> > > > As a note, the solvent will 'not' clear blocked tubes. They do need
> to
> > > > be reamed out with a piece of wire at the least, and oversized with a
> > > > welding torch tip drill or file to help keep the suckers clear. I
> think
> > > > half the dirt that gets in them comes from that U shaped chunk of gas
> > > > line between the filter and carb. It needs serious cleaning on most.
> > > >
> > > > Here is a link on the tubes:
> > > > http://www.off-road.com/jeep/tech/engine/carter.html
> > > >
> > > > Don't forget that the gas filter has to be in right side up.... It
> has
> > > > 2 outlets. The center one goes to the carb and the top one goes to
> the
> > > > return line. If the return line isn't up top, gas can syphon back to
> > > > the tank when it sits.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > > Canadian Off Road Trips Photos: Non members can still view!
> > > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > > > (More Off Road album links at bottom of the view page)
> > > >
model in it which makes it confusing right off the bat.
They have a sneaky base plate add on too. The sucker has 4 little
notches in it that have to be on the top side and not covered by a
gasket or the carb won't get vacuum to it's ports.
Mike
Earle Horton wrote:
>
> I have seen this happen a lot. It is almost as if the designers wanted the
> carburetor to "almost work" with a gasket in wrong. Sometimes, they put
> extra gaskets in carburetor rebuild kits, that apparently don't fit any
> model carburetor ever made. I don't know how many shade tree mechanics and
> professional mechanics too have been caught by this little joke. Let's just
> say that I found out about it the hard way too.
>
> Earle
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:443D14B4.4DD1B29@sympatico.ca...
> > Cool.
> >
> > Mike
> >
> > JohanB wrote:
> > >
> > > Hey....
> > >
> > > Took the idle tubes out like you suggested.
> > > They were clean
> > > double checked everything and found that the idiot that "overhauled " it
> > > before swapped the gaskets.
> > > He put the lower gasket between the idle tube cover and the idle tube
> gasket
> > > under the venturi cluster causing it to leave a little gap between the
> idle
> > > tube cover and venturi cluster where the gas dripped out.
> > >
> > > Off course the last idiot that worked on it just peeled the old gaskets
> off
> > > and also put the new 1's in wrong
> > > ( oh wait , that was me...... :-) )
> > >
> > > after starting it and cleaning the gas out off the manifold I started it
> > > again after an hour and it fired right up
> > >
> > > Thanks yall for the tips
> > >
> > > "Mike Romain" <romainm@sympatico.ca> wrote in message
> > > news:443A6531.9C0108CB@sympatico.ca...
> > > > I have had the exact same trouble with the last kit I put in. The
> float
> > > > needle and seat were bad. The store warrantied them.
> > > >
> > > > The idle tubes are those two long brass tubes that hang down. They
> are
> > > > real sneaky for plugging up. I can just remove the choke plate and
> then
> > > > the two screws holding the venturi in and lift and twist the venturi
> > > > around so it slips out without removing the whole top of the carb for
> > > > cleaning. You have to blow through the tubes to make sure they are
> > > > clear. The tubes 'can' fall out too.
> > > >
> > > > As a note, the solvent will 'not' clear blocked tubes. They do need
> to
> > > > be reamed out with a piece of wire at the least, and oversized with a
> > > > welding torch tip drill or file to help keep the suckers clear. I
> think
> > > > half the dirt that gets in them comes from that U shaped chunk of gas
> > > > line between the filter and carb. It needs serious cleaning on most.
> > > >
> > > > Here is a link on the tubes:
> > > > http://www.off-road.com/jeep/tech/engine/carter.html
> > > >
> > > > Don't forget that the gas filter has to be in right side up.... It
> has
> > > > 2 outlets. The center one goes to the carb and the top one goes to
> the
> > > > return line. If the return line isn't up top, gas can syphon back to
> > > > the tank when it sits.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > > Canadian Off Road Trips Photos: Non members can still view!
> > > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > > > (More Off Road album links at bottom of the view page)
> > > >
#52
Guest
Posts: n/a
Re: Carter 2bbl specs-- update / fixed
The BBD kit has gaskets for both the electric model and the standard
model in it which makes it confusing right off the bat.
They have a sneaky base plate add on too. The sucker has 4 little
notches in it that have to be on the top side and not covered by a
gasket or the carb won't get vacuum to it's ports.
Mike
Earle Horton wrote:
>
> I have seen this happen a lot. It is almost as if the designers wanted the
> carburetor to "almost work" with a gasket in wrong. Sometimes, they put
> extra gaskets in carburetor rebuild kits, that apparently don't fit any
> model carburetor ever made. I don't know how many shade tree mechanics and
> professional mechanics too have been caught by this little joke. Let's just
> say that I found out about it the hard way too.
>
> Earle
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:443D14B4.4DD1B29@sympatico.ca...
> > Cool.
> >
> > Mike
> >
> > JohanB wrote:
> > >
> > > Hey....
> > >
> > > Took the idle tubes out like you suggested.
> > > They were clean
> > > double checked everything and found that the idiot that "overhauled " it
> > > before swapped the gaskets.
> > > He put the lower gasket between the idle tube cover and the idle tube
> gasket
> > > under the venturi cluster causing it to leave a little gap between the
> idle
> > > tube cover and venturi cluster where the gas dripped out.
> > >
> > > Off course the last idiot that worked on it just peeled the old gaskets
> off
> > > and also put the new 1's in wrong
> > > ( oh wait , that was me...... :-) )
> > >
> > > after starting it and cleaning the gas out off the manifold I started it
> > > again after an hour and it fired right up
> > >
> > > Thanks yall for the tips
> > >
> > > "Mike Romain" <romainm@sympatico.ca> wrote in message
> > > news:443A6531.9C0108CB@sympatico.ca...
> > > > I have had the exact same trouble with the last kit I put in. The
> float
> > > > needle and seat were bad. The store warrantied them.
> > > >
> > > > The idle tubes are those two long brass tubes that hang down. They
> are
> > > > real sneaky for plugging up. I can just remove the choke plate and
> then
> > > > the two screws holding the venturi in and lift and twist the venturi
> > > > around so it slips out without removing the whole top of the carb for
> > > > cleaning. You have to blow through the tubes to make sure they are
> > > > clear. The tubes 'can' fall out too.
> > > >
> > > > As a note, the solvent will 'not' clear blocked tubes. They do need
> to
> > > > be reamed out with a piece of wire at the least, and oversized with a
> > > > welding torch tip drill or file to help keep the suckers clear. I
> think
> > > > half the dirt that gets in them comes from that U shaped chunk of gas
> > > > line between the filter and carb. It needs serious cleaning on most.
> > > >
> > > > Here is a link on the tubes:
> > > > http://www.off-road.com/jeep/tech/engine/carter.html
> > > >
> > > > Don't forget that the gas filter has to be in right side up.... It
> has
> > > > 2 outlets. The center one goes to the carb and the top one goes to
> the
> > > > return line. If the return line isn't up top, gas can syphon back to
> > > > the tank when it sits.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > > Canadian Off Road Trips Photos: Non members can still view!
> > > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > > > (More Off Road album links at bottom of the view page)
> > > >
model in it which makes it confusing right off the bat.
They have a sneaky base plate add on too. The sucker has 4 little
notches in it that have to be on the top side and not covered by a
gasket or the carb won't get vacuum to it's ports.
Mike
Earle Horton wrote:
>
> I have seen this happen a lot. It is almost as if the designers wanted the
> carburetor to "almost work" with a gasket in wrong. Sometimes, they put
> extra gaskets in carburetor rebuild kits, that apparently don't fit any
> model carburetor ever made. I don't know how many shade tree mechanics and
> professional mechanics too have been caught by this little joke. Let's just
> say that I found out about it the hard way too.
>
> Earle
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:443D14B4.4DD1B29@sympatico.ca...
> > Cool.
> >
> > Mike
> >
> > JohanB wrote:
> > >
> > > Hey....
> > >
> > > Took the idle tubes out like you suggested.
> > > They were clean
> > > double checked everything and found that the idiot that "overhauled " it
> > > before swapped the gaskets.
> > > He put the lower gasket between the idle tube cover and the idle tube
> gasket
> > > under the venturi cluster causing it to leave a little gap between the
> idle
> > > tube cover and venturi cluster where the gas dripped out.
> > >
> > > Off course the last idiot that worked on it just peeled the old gaskets
> off
> > > and also put the new 1's in wrong
> > > ( oh wait , that was me...... :-) )
> > >
> > > after starting it and cleaning the gas out off the manifold I started it
> > > again after an hour and it fired right up
> > >
> > > Thanks yall for the tips
> > >
> > > "Mike Romain" <romainm@sympatico.ca> wrote in message
> > > news:443A6531.9C0108CB@sympatico.ca...
> > > > I have had the exact same trouble with the last kit I put in. The
> float
> > > > needle and seat were bad. The store warrantied them.
> > > >
> > > > The idle tubes are those two long brass tubes that hang down. They
> are
> > > > real sneaky for plugging up. I can just remove the choke plate and
> then
> > > > the two screws holding the venturi in and lift and twist the venturi
> > > > around so it slips out without removing the whole top of the carb for
> > > > cleaning. You have to blow through the tubes to make sure they are
> > > > clear. The tubes 'can' fall out too.
> > > >
> > > > As a note, the solvent will 'not' clear blocked tubes. They do need
> to
> > > > be reamed out with a piece of wire at the least, and oversized with a
> > > > welding torch tip drill or file to help keep the suckers clear. I
> think
> > > > half the dirt that gets in them comes from that U shaped chunk of gas
> > > > line between the filter and carb. It needs serious cleaning on most.
> > > >
> > > > Here is a link on the tubes:
> > > > http://www.off-road.com/jeep/tech/engine/carter.html
> > > >
> > > > Don't forget that the gas filter has to be in right side up.... It
> has
> > > > 2 outlets. The center one goes to the carb and the top one goes to
> the
> > > > return line. If the return line isn't up top, gas can syphon back to
> > > > the tank when it sits.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > > Canadian Off Road Trips Photos: Non members can still view!
> > > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > > > (More Off Road album links at bottom of the view page)
> > > >
#53
Guest
Posts: n/a
Re: Carter 2bbl specs-- update / fixed
Hi Mike,
And I've seen many kit manufacturers have the wrong gaskets in
them, one I remember didn't have the hole necessary to run the
accelerator pump.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Mike Romain wrote:
>
> The BBD kit has gaskets for both the electric model and the standard
> model in it which makes it confusing right off the bat.
>
> They have a sneaky base plate add on too. The sucker has 4 little
> notches in it that have to be on the top side and not covered by a
> gasket or the carb won't get vacuum to it's ports.
>
> Mike
And I've seen many kit manufacturers have the wrong gaskets in
them, one I remember didn't have the hole necessary to run the
accelerator pump.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Mike Romain wrote:
>
> The BBD kit has gaskets for both the electric model and the standard
> model in it which makes it confusing right off the bat.
>
> They have a sneaky base plate add on too. The sucker has 4 little
> notches in it that have to be on the top side and not covered by a
> gasket or the carb won't get vacuum to it's ports.
>
> Mike
#54
Guest
Posts: n/a
Re: Carter 2bbl specs-- update / fixed
Hi Mike,
And I've seen many kit manufacturers have the wrong gaskets in
them, one I remember didn't have the hole necessary to run the
accelerator pump.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Mike Romain wrote:
>
> The BBD kit has gaskets for both the electric model and the standard
> model in it which makes it confusing right off the bat.
>
> They have a sneaky base plate add on too. The sucker has 4 little
> notches in it that have to be on the top side and not covered by a
> gasket or the carb won't get vacuum to it's ports.
>
> Mike
And I've seen many kit manufacturers have the wrong gaskets in
them, one I remember didn't have the hole necessary to run the
accelerator pump.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Mike Romain wrote:
>
> The BBD kit has gaskets for both the electric model and the standard
> model in it which makes it confusing right off the bat.
>
> They have a sneaky base plate add on too. The sucker has 4 little
> notches in it that have to be on the top side and not covered by a
> gasket or the carb won't get vacuum to it's ports.
>
> Mike
#55
Guest
Posts: n/a
Re: Carter 2bbl specs-- update / fixed
Hi Mike,
And I've seen many kit manufacturers have the wrong gaskets in
them, one I remember didn't have the hole necessary to run the
accelerator pump.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Mike Romain wrote:
>
> The BBD kit has gaskets for both the electric model and the standard
> model in it which makes it confusing right off the bat.
>
> They have a sneaky base plate add on too. The sucker has 4 little
> notches in it that have to be on the top side and not covered by a
> gasket or the carb won't get vacuum to it's ports.
>
> Mike
And I've seen many kit manufacturers have the wrong gaskets in
them, one I remember didn't have the hole necessary to run the
accelerator pump.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Mike Romain wrote:
>
> The BBD kit has gaskets for both the electric model and the standard
> model in it which makes it confusing right off the bat.
>
> They have a sneaky base plate add on too. The sucker has 4 little
> notches in it that have to be on the top side and not covered by a
> gasket or the carb won't get vacuum to it's ports.
>
> Mike
Thread
Thread Starter
Forum
Replies
Last Post
=?ISO-8859-1?Q?=22L=2EW=2E=28=DFill=29_Hughes_III=22?=
Jeep Mailing List
0
09-01-2003 04:10 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)