93 Grand Cherokee Power Window
07-13-2006, 10:39 AM
#21
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
And an update.
Got the scissor rack out, along with the motor and gear assembly. I remember
this setup now as it about took my thumb off a few years ago when I unbolted
the motor from the housing. There's a powerful spring there.
Anyway, I hooked it all up electrically outside the door and tried it.
Nothing. Tapped on the motor housing and 'poof' it works smoothly and
strongly now.
Any bets on how long it will last now? Hopefully for another month when my
raise kicks in and I can trade the old gal in on an '01 or '02. She's
getting to be too much for me.
Thanks all for your help and support.
D
"DougW" <post.replies@invalid.address> wrote in message
news:1Dgtg.66419$9c6.43085@dukeread11...
> "D" wrote ...
> > Hi All,
> > The window went down in the driver door and wont go back up. Power to it
> > okay.
> > Is there a web site that shows picks of the regulator, et-al so I can
clean
> > it up? Maybe make it work for a little while longer?
> > I'll be putting the switch back together as I wait for an answer. Heh.
>
> Take the door panel off (watch the edges they are very sharp)
> then look at the plastic connector that snaps to the power window
> switch assembly. Odds are it has come unhooked. The way that
> switch works if the motor has power then it has to be the switch
> or the connector. The one on my passenger side broke and I had
> to put a zip-tie in to hold it on.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
Got the scissor rack out, along with the motor and gear assembly. I remember
this setup now as it about took my thumb off a few years ago when I unbolted
the motor from the housing. There's a powerful spring there.
Anyway, I hooked it all up electrically outside the door and tried it.
Nothing. Tapped on the motor housing and 'poof' it works smoothly and
strongly now.
Any bets on how long it will last now? Hopefully for another month when my
raise kicks in and I can trade the old gal in on an '01 or '02. She's
getting to be too much for me.
Thanks all for your help and support.
D
"DougW" <post.replies@invalid.address> wrote in message
news:1Dgtg.66419$9c6.43085@dukeread11...
> "D" wrote ...
> > Hi All,
> > The window went down in the driver door and wont go back up. Power to it
> > okay.
> > Is there a web site that shows picks of the regulator, et-al so I can
clean
> > it up? Maybe make it work for a little while longer?
> > I'll be putting the switch back together as I wait for an answer. Heh.
>
> Take the door panel off (watch the edges they are very sharp)
> then look at the plastic connector that snaps to the power window
> switch assembly. Odds are it has come unhooked. The way that
> switch works if the motor has power then it has to be the switch
> or the connector. The one on my passenger side broke and I had
> to put a zip-tie in to hold it on.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
07-13-2006, 10:39 AM
#22
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
And an update.
Got the scissor rack out, along with the motor and gear assembly. I remember
this setup now as it about took my thumb off a few years ago when I unbolted
the motor from the housing. There's a powerful spring there.
Anyway, I hooked it all up electrically outside the door and tried it.
Nothing. Tapped on the motor housing and 'poof' it works smoothly and
strongly now.
Any bets on how long it will last now? Hopefully for another month when my
raise kicks in and I can trade the old gal in on an '01 or '02. She's
getting to be too much for me.
Thanks all for your help and support.
D
"DougW" <post.replies@invalid.address> wrote in message
news:1Dgtg.66419$9c6.43085@dukeread11...
> "D" wrote ...
> > Hi All,
> > The window went down in the driver door and wont go back up. Power to it
> > okay.
> > Is there a web site that shows picks of the regulator, et-al so I can
clean
> > it up? Maybe make it work for a little while longer?
> > I'll be putting the switch back together as I wait for an answer. Heh.
>
> Take the door panel off (watch the edges they are very sharp)
> then look at the plastic connector that snaps to the power window
> switch assembly. Odds are it has come unhooked. The way that
> switch works if the motor has power then it has to be the switch
> or the connector. The one on my passenger side broke and I had
> to put a zip-tie in to hold it on.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
Got the scissor rack out, along with the motor and gear assembly. I remember
this setup now as it about took my thumb off a few years ago when I unbolted
the motor from the housing. There's a powerful spring there.
Anyway, I hooked it all up electrically outside the door and tried it.
Nothing. Tapped on the motor housing and 'poof' it works smoothly and
strongly now.
Any bets on how long it will last now? Hopefully for another month when my
raise kicks in and I can trade the old gal in on an '01 or '02. She's
getting to be too much for me.
Thanks all for your help and support.
D
"DougW" <post.replies@invalid.address> wrote in message
news:1Dgtg.66419$9c6.43085@dukeread11...
> "D" wrote ...
> > Hi All,
> > The window went down in the driver door and wont go back up. Power to it
> > okay.
> > Is there a web site that shows picks of the regulator, et-al so I can
clean
> > it up? Maybe make it work for a little while longer?
> > I'll be putting the switch back together as I wait for an answer. Heh.
>
> Take the door panel off (watch the edges they are very sharp)
> then look at the plastic connector that snaps to the power window
> switch assembly. Odds are it has come unhooked. The way that
> switch works if the motor has power then it has to be the switch
> or the connector. The one on my passenger side broke and I had
> to put a zip-tie in to hold it on.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
07-13-2006, 11:01 AM
#23
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
You are describing either gummed up or worn out brushes in the motor.
You 'might' be able to open it and hit up a (starter) motor rebuilder
for a set of brushes. That's what I do when my starter acts like that.
(needing a hit to set the brushes again) My XJ starter's brush pack set
me back about $15.00 if I remember right.
Or you could be lucky and only need some WD40 to clean out the dust that
mixed with the grease to gum up the brushes.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
D wrote:
>
> And an update.
> Got the scissor rack out, along with the motor and gear assembly. I remember
> this setup now as it about took my thumb off a few years ago when I unbolted
> the motor from the housing. There's a powerful spring there.
> Anyway, I hooked it all up electrically outside the door and tried it.
> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> strongly now.
> Any bets on how long it will last now? Hopefully for another month when my
> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> getting to be too much for me.
> Thanks all for your help and support.
> D
>
> "DougW" <post.replies@invalid.address> wrote in message
> news:1Dgtg.66419$9c6.43085@dukeread11...
> > "D" wrote ...
> > > Hi All,
> > > The window went down in the driver door and wont go back up. Power to it
> > > okay.
> > > Is there a web site that shows picks of the regulator, et-al so I can
> clean
> > > it up? Maybe make it work for a little while longer?
> > > I'll be putting the switch back together as I wait for an answer. Heh.
> >
> > Take the door panel off (watch the edges they are very sharp)
> > then look at the plastic connector that snaps to the power window
> > switch assembly. Odds are it has come unhooked. The way that
> > switch works if the motor has power then it has to be the switch
> > or the connector. The one on my passenger side broke and I had
> > to put a zip-tie in to hold it on.
> >
> > --
> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > Banks Header - and BEER, in the fridge!
> >
> >
You 'might' be able to open it and hit up a (starter) motor rebuilder
for a set of brushes. That's what I do when my starter acts like that.
(needing a hit to set the brushes again) My XJ starter's brush pack set
me back about $15.00 if I remember right.
Or you could be lucky and only need some WD40 to clean out the dust that
mixed with the grease to gum up the brushes.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
D wrote:
>
> And an update.
> Got the scissor rack out, along with the motor and gear assembly. I remember
> this setup now as it about took my thumb off a few years ago when I unbolted
> the motor from the housing. There's a powerful spring there.
> Anyway, I hooked it all up electrically outside the door and tried it.
> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> strongly now.
> Any bets on how long it will last now? Hopefully for another month when my
> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> getting to be too much for me.
> Thanks all for your help and support.
> D
>
> "DougW" <post.replies@invalid.address> wrote in message
> news:1Dgtg.66419$9c6.43085@dukeread11...
> > "D" wrote ...
> > > Hi All,
> > > The window went down in the driver door and wont go back up. Power to it
> > > okay.
> > > Is there a web site that shows picks of the regulator, et-al so I can
> clean
> > > it up? Maybe make it work for a little while longer?
> > > I'll be putting the switch back together as I wait for an answer. Heh.
> >
> > Take the door panel off (watch the edges they are very sharp)
> > then look at the plastic connector that snaps to the power window
> > switch assembly. Odds are it has come unhooked. The way that
> > switch works if the motor has power then it has to be the switch
> > or the connector. The one on my passenger side broke and I had
> > to put a zip-tie in to hold it on.
> >
> > --
> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > Banks Header - and BEER, in the fridge!
> >
> >
07-13-2006, 11:01 AM
#24
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
You are describing either gummed up or worn out brushes in the motor.
You 'might' be able to open it and hit up a (starter) motor rebuilder
for a set of brushes. That's what I do when my starter acts like that.
(needing a hit to set the brushes again) My XJ starter's brush pack set
me back about $15.00 if I remember right.
Or you could be lucky and only need some WD40 to clean out the dust that
mixed with the grease to gum up the brushes.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
D wrote:
>
> And an update.
> Got the scissor rack out, along with the motor and gear assembly. I remember
> this setup now as it about took my thumb off a few years ago when I unbolted
> the motor from the housing. There's a powerful spring there.
> Anyway, I hooked it all up electrically outside the door and tried it.
> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> strongly now.
> Any bets on how long it will last now? Hopefully for another month when my
> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> getting to be too much for me.
> Thanks all for your help and support.
> D
>
> "DougW" <post.replies@invalid.address> wrote in message
> news:1Dgtg.66419$9c6.43085@dukeread11...
> > "D" wrote ...
> > > Hi All,
> > > The window went down in the driver door and wont go back up. Power to it
> > > okay.
> > > Is there a web site that shows picks of the regulator, et-al so I can
> clean
> > > it up? Maybe make it work for a little while longer?
> > > I'll be putting the switch back together as I wait for an answer. Heh.
> >
> > Take the door panel off (watch the edges they are very sharp)
> > then look at the plastic connector that snaps to the power window
> > switch assembly. Odds are it has come unhooked. The way that
> > switch works if the motor has power then it has to be the switch
> > or the connector. The one on my passenger side broke and I had
> > to put a zip-tie in to hold it on.
> >
> > --
> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > Banks Header - and BEER, in the fridge!
> >
> >
You 'might' be able to open it and hit up a (starter) motor rebuilder
for a set of brushes. That's what I do when my starter acts like that.
(needing a hit to set the brushes again) My XJ starter's brush pack set
me back about $15.00 if I remember right.
Or you could be lucky and only need some WD40 to clean out the dust that
mixed with the grease to gum up the brushes.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
D wrote:
>
> And an update.
> Got the scissor rack out, along with the motor and gear assembly. I remember
> this setup now as it about took my thumb off a few years ago when I unbolted
> the motor from the housing. There's a powerful spring there.
> Anyway, I hooked it all up electrically outside the door and tried it.
> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> strongly now.
> Any bets on how long it will last now? Hopefully for another month when my
> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> getting to be too much for me.
> Thanks all for your help and support.
> D
>
> "DougW" <post.replies@invalid.address> wrote in message
> news:1Dgtg.66419$9c6.43085@dukeread11...
> > "D" wrote ...
> > > Hi All,
> > > The window went down in the driver door and wont go back up. Power to it
> > > okay.
> > > Is there a web site that shows picks of the regulator, et-al so I can
> clean
> > > it up? Maybe make it work for a little while longer?
> > > I'll be putting the switch back together as I wait for an answer. Heh.
> >
> > Take the door panel off (watch the edges they are very sharp)
> > then look at the plastic connector that snaps to the power window
> > switch assembly. Odds are it has come unhooked. The way that
> > switch works if the motor has power then it has to be the switch
> > or the connector. The one on my passenger side broke and I had
> > to put a zip-tie in to hold it on.
> >
> > --
> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > Banks Header - and BEER, in the fridge!
> >
> >
07-13-2006, 11:01 AM
#25
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
You are describing either gummed up or worn out brushes in the motor.
You 'might' be able to open it and hit up a (starter) motor rebuilder
for a set of brushes. That's what I do when my starter acts like that.
(needing a hit to set the brushes again) My XJ starter's brush pack set
me back about $15.00 if I remember right.
Or you could be lucky and only need some WD40 to clean out the dust that
mixed with the grease to gum up the brushes.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
D wrote:
>
> And an update.
> Got the scissor rack out, along with the motor and gear assembly. I remember
> this setup now as it about took my thumb off a few years ago when I unbolted
> the motor from the housing. There's a powerful spring there.
> Anyway, I hooked it all up electrically outside the door and tried it.
> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> strongly now.
> Any bets on how long it will last now? Hopefully for another month when my
> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> getting to be too much for me.
> Thanks all for your help and support.
> D
>
> "DougW" <post.replies@invalid.address> wrote in message
> news:1Dgtg.66419$9c6.43085@dukeread11...
> > "D" wrote ...
> > > Hi All,
> > > The window went down in the driver door and wont go back up. Power to it
> > > okay.
> > > Is there a web site that shows picks of the regulator, et-al so I can
> clean
> > > it up? Maybe make it work for a little while longer?
> > > I'll be putting the switch back together as I wait for an answer. Heh.
> >
> > Take the door panel off (watch the edges they are very sharp)
> > then look at the plastic connector that snaps to the power window
> > switch assembly. Odds are it has come unhooked. The way that
> > switch works if the motor has power then it has to be the switch
> > or the connector. The one on my passenger side broke and I had
> > to put a zip-tie in to hold it on.
> >
> > --
> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > Banks Header - and BEER, in the fridge!
> >
> >
You 'might' be able to open it and hit up a (starter) motor rebuilder
for a set of brushes. That's what I do when my starter acts like that.
(needing a hit to set the brushes again) My XJ starter's brush pack set
me back about $15.00 if I remember right.
Or you could be lucky and only need some WD40 to clean out the dust that
mixed with the grease to gum up the brushes.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
D wrote:
>
> And an update.
> Got the scissor rack out, along with the motor and gear assembly. I remember
> this setup now as it about took my thumb off a few years ago when I unbolted
> the motor from the housing. There's a powerful spring there.
> Anyway, I hooked it all up electrically outside the door and tried it.
> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> strongly now.
> Any bets on how long it will last now? Hopefully for another month when my
> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> getting to be too much for me.
> Thanks all for your help and support.
> D
>
> "DougW" <post.replies@invalid.address> wrote in message
> news:1Dgtg.66419$9c6.43085@dukeread11...
> > "D" wrote ...
> > > Hi All,
> > > The window went down in the driver door and wont go back up. Power to it
> > > okay.
> > > Is there a web site that shows picks of the regulator, et-al so I can
> clean
> > > it up? Maybe make it work for a little while longer?
> > > I'll be putting the switch back together as I wait for an answer. Heh.
> >
> > Take the door panel off (watch the edges they are very sharp)
> > then look at the plastic connector that snaps to the power window
> > switch assembly. Odds are it has come unhooked. The way that
> > switch works if the motor has power then it has to be the switch
> > or the connector. The one on my passenger side broke and I had
> > to put a zip-tie in to hold it on.
> >
> > --
> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> > Banks Header - and BEER, in the fridge!
> >
> >
07-13-2006, 12:21 PM
#26
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
If it is crud in there, I would recommend using the electrical contact spray
cleaner. Car-Quest has one here that is called extra strength, and it works
great. I was sold on it after using it to clean a blower motor on a
commercial deep fryer. Many years of dust and grease came clean with no
effort at all. I'm sure most of the spray cleaners are about the same, but I
know this stuff worked great.
Chris
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:44B66052.5B106C21@sympatico.ca...
> You are describing either gummed up or worn out brushes in the motor.
>
> You 'might' be able to open it and hit up a (starter) motor rebuilder
> for a set of brushes. That's what I do when my starter acts like that.
> (needing a hit to set the brushes again) My XJ starter's brush pack set
> me back about $15.00 if I remember right.
>
> Or you could be lucky and only need some WD40 to clean out the dust that
> mixed with the grease to gum up the brushes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> D wrote:
>>
>> And an update.
>> Got the scissor rack out, along with the motor and gear assembly. I
>> remember
>> this setup now as it about took my thumb off a few years ago when I
>> unbolted
>> the motor from the housing. There's a powerful spring there.
>> Anyway, I hooked it all up electrically outside the door and tried it.
>> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
>> strongly now.
>> Any bets on how long it will last now? Hopefully for another month when
>> my
>> raise kicks in and I can trade the old gal in on an '01 or '02. She's
>> getting to be too much for me.
>> Thanks all for your help and support.
>> D
>>
>> "DougW" <post.replies@invalid.address> wrote in message
>> news:1Dgtg.66419$9c6.43085@dukeread11...
>> > "D" wrote ...
>> > > Hi All,
>> > > The window went down in the driver door and wont go back up. Power to
>> > > it
>> > > okay.
>> > > Is there a web site that shows picks of the regulator, et-al so I can
>> clean
>> > > it up? Maybe make it work for a little while longer?
>> > > I'll be putting the switch back together as I wait for an answer.
>> > > Heh.
>> >
>> > Take the door panel off (watch the edges they are very sharp)
>> > then look at the plastic connector that snaps to the power window
>> > switch assembly. Odds are it has come unhooked. The way that
>> > switch works if the motor has power then it has to be the switch
>> > or the connector. The one on my passenger side broke and I had
>> > to put a zip-tie in to hold it on.
>> >
>> > --
>> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
>> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
>> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
>> > Banks Header - and BEER, in the fridge!
>> >
>> >
cleaner. Car-Quest has one here that is called extra strength, and it works
great. I was sold on it after using it to clean a blower motor on a
commercial deep fryer. Many years of dust and grease came clean with no
effort at all. I'm sure most of the spray cleaners are about the same, but I
know this stuff worked great.
Chris
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:44B66052.5B106C21@sympatico.ca...
> You are describing either gummed up or worn out brushes in the motor.
>
> You 'might' be able to open it and hit up a (starter) motor rebuilder
> for a set of brushes. That's what I do when my starter acts like that.
> (needing a hit to set the brushes again) My XJ starter's brush pack set
> me back about $15.00 if I remember right.
>
> Or you could be lucky and only need some WD40 to clean out the dust that
> mixed with the grease to gum up the brushes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> D wrote:
>>
>> And an update.
>> Got the scissor rack out, along with the motor and gear assembly. I
>> remember
>> this setup now as it about took my thumb off a few years ago when I
>> unbolted
>> the motor from the housing. There's a powerful spring there.
>> Anyway, I hooked it all up electrically outside the door and tried it.
>> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
>> strongly now.
>> Any bets on how long it will last now? Hopefully for another month when
>> my
>> raise kicks in and I can trade the old gal in on an '01 or '02. She's
>> getting to be too much for me.
>> Thanks all for your help and support.
>> D
>>
>> "DougW" <post.replies@invalid.address> wrote in message
>> news:1Dgtg.66419$9c6.43085@dukeread11...
>> > "D" wrote ...
>> > > Hi All,
>> > > The window went down in the driver door and wont go back up. Power to
>> > > it
>> > > okay.
>> > > Is there a web site that shows picks of the regulator, et-al so I can
>> clean
>> > > it up? Maybe make it work for a little while longer?
>> > > I'll be putting the switch back together as I wait for an answer.
>> > > Heh.
>> >
>> > Take the door panel off (watch the edges they are very sharp)
>> > then look at the plastic connector that snaps to the power window
>> > switch assembly. Odds are it has come unhooked. The way that
>> > switch works if the motor has power then it has to be the switch
>> > or the connector. The one on my passenger side broke and I had
>> > to put a zip-tie in to hold it on.
>> >
>> > --
>> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
>> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
>> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
>> > Banks Header - and BEER, in the fridge!
>> >
>> >
07-13-2006, 12:21 PM
#27
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
If it is crud in there, I would recommend using the electrical contact spray
cleaner. Car-Quest has one here that is called extra strength, and it works
great. I was sold on it after using it to clean a blower motor on a
commercial deep fryer. Many years of dust and grease came clean with no
effort at all. I'm sure most of the spray cleaners are about the same, but I
know this stuff worked great.
Chris
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:44B66052.5B106C21@sympatico.ca...
> You are describing either gummed up or worn out brushes in the motor.
>
> You 'might' be able to open it and hit up a (starter) motor rebuilder
> for a set of brushes. That's what I do when my starter acts like that.
> (needing a hit to set the brushes again) My XJ starter's brush pack set
> me back about $15.00 if I remember right.
>
> Or you could be lucky and only need some WD40 to clean out the dust that
> mixed with the grease to gum up the brushes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> D wrote:
>>
>> And an update.
>> Got the scissor rack out, along with the motor and gear assembly. I
>> remember
>> this setup now as it about took my thumb off a few years ago when I
>> unbolted
>> the motor from the housing. There's a powerful spring there.
>> Anyway, I hooked it all up electrically outside the door and tried it.
>> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
>> strongly now.
>> Any bets on how long it will last now? Hopefully for another month when
>> my
>> raise kicks in and I can trade the old gal in on an '01 or '02. She's
>> getting to be too much for me.
>> Thanks all for your help and support.
>> D
>>
>> "DougW" <post.replies@invalid.address> wrote in message
>> news:1Dgtg.66419$9c6.43085@dukeread11...
>> > "D" wrote ...
>> > > Hi All,
>> > > The window went down in the driver door and wont go back up. Power to
>> > > it
>> > > okay.
>> > > Is there a web site that shows picks of the regulator, et-al so I can
>> clean
>> > > it up? Maybe make it work for a little while longer?
>> > > I'll be putting the switch back together as I wait for an answer.
>> > > Heh.
>> >
>> > Take the door panel off (watch the edges they are very sharp)
>> > then look at the plastic connector that snaps to the power window
>> > switch assembly. Odds are it has come unhooked. The way that
>> > switch works if the motor has power then it has to be the switch
>> > or the connector. The one on my passenger side broke and I had
>> > to put a zip-tie in to hold it on.
>> >
>> > --
>> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
>> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
>> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
>> > Banks Header - and BEER, in the fridge!
>> >
>> >
cleaner. Car-Quest has one here that is called extra strength, and it works
great. I was sold on it after using it to clean a blower motor on a
commercial deep fryer. Many years of dust and grease came clean with no
effort at all. I'm sure most of the spray cleaners are about the same, but I
know this stuff worked great.
Chris
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:44B66052.5B106C21@sympatico.ca...
> You are describing either gummed up or worn out brushes in the motor.
>
> You 'might' be able to open it and hit up a (starter) motor rebuilder
> for a set of brushes. That's what I do when my starter acts like that.
> (needing a hit to set the brushes again) My XJ starter's brush pack set
> me back about $15.00 if I remember right.
>
> Or you could be lucky and only need some WD40 to clean out the dust that
> mixed with the grease to gum up the brushes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> D wrote:
>>
>> And an update.
>> Got the scissor rack out, along with the motor and gear assembly. I
>> remember
>> this setup now as it about took my thumb off a few years ago when I
>> unbolted
>> the motor from the housing. There's a powerful spring there.
>> Anyway, I hooked it all up electrically outside the door and tried it.
>> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
>> strongly now.
>> Any bets on how long it will last now? Hopefully for another month when
>> my
>> raise kicks in and I can trade the old gal in on an '01 or '02. She's
>> getting to be too much for me.
>> Thanks all for your help and support.
>> D
>>
>> "DougW" <post.replies@invalid.address> wrote in message
>> news:1Dgtg.66419$9c6.43085@dukeread11...
>> > "D" wrote ...
>> > > Hi All,
>> > > The window went down in the driver door and wont go back up. Power to
>> > > it
>> > > okay.
>> > > Is there a web site that shows picks of the regulator, et-al so I can
>> clean
>> > > it up? Maybe make it work for a little while longer?
>> > > I'll be putting the switch back together as I wait for an answer.
>> > > Heh.
>> >
>> > Take the door panel off (watch the edges they are very sharp)
>> > then look at the plastic connector that snaps to the power window
>> > switch assembly. Odds are it has come unhooked. The way that
>> > switch works if the motor has power then it has to be the switch
>> > or the connector. The one on my passenger side broke and I had
>> > to put a zip-tie in to hold it on.
>> >
>> > --
>> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
>> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
>> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
>> > Banks Header - and BEER, in the fridge!
>> >
>> >
07-13-2006, 12:21 PM
#28
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
If it is crud in there, I would recommend using the electrical contact spray
cleaner. Car-Quest has one here that is called extra strength, and it works
great. I was sold on it after using it to clean a blower motor on a
commercial deep fryer. Many years of dust and grease came clean with no
effort at all. I'm sure most of the spray cleaners are about the same, but I
know this stuff worked great.
Chris
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:44B66052.5B106C21@sympatico.ca...
> You are describing either gummed up or worn out brushes in the motor.
>
> You 'might' be able to open it and hit up a (starter) motor rebuilder
> for a set of brushes. That's what I do when my starter acts like that.
> (needing a hit to set the brushes again) My XJ starter's brush pack set
> me back about $15.00 if I remember right.
>
> Or you could be lucky and only need some WD40 to clean out the dust that
> mixed with the grease to gum up the brushes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> D wrote:
>>
>> And an update.
>> Got the scissor rack out, along with the motor and gear assembly. I
>> remember
>> this setup now as it about took my thumb off a few years ago when I
>> unbolted
>> the motor from the housing. There's a powerful spring there.
>> Anyway, I hooked it all up electrically outside the door and tried it.
>> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
>> strongly now.
>> Any bets on how long it will last now? Hopefully for another month when
>> my
>> raise kicks in and I can trade the old gal in on an '01 or '02. She's
>> getting to be too much for me.
>> Thanks all for your help and support.
>> D
>>
>> "DougW" <post.replies@invalid.address> wrote in message
>> news:1Dgtg.66419$9c6.43085@dukeread11...
>> > "D" wrote ...
>> > > Hi All,
>> > > The window went down in the driver door and wont go back up. Power to
>> > > it
>> > > okay.
>> > > Is there a web site that shows picks of the regulator, et-al so I can
>> clean
>> > > it up? Maybe make it work for a little while longer?
>> > > I'll be putting the switch back together as I wait for an answer.
>> > > Heh.
>> >
>> > Take the door panel off (watch the edges they are very sharp)
>> > then look at the plastic connector that snaps to the power window
>> > switch assembly. Odds are it has come unhooked. The way that
>> > switch works if the motor has power then it has to be the switch
>> > or the connector. The one on my passenger side broke and I had
>> > to put a zip-tie in to hold it on.
>> >
>> > --
>> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
>> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
>> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
>> > Banks Header - and BEER, in the fridge!
>> >
>> >
cleaner. Car-Quest has one here that is called extra strength, and it works
great. I was sold on it after using it to clean a blower motor on a
commercial deep fryer. Many years of dust and grease came clean with no
effort at all. I'm sure most of the spray cleaners are about the same, but I
know this stuff worked great.
Chris
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:44B66052.5B106C21@sympatico.ca...
> You are describing either gummed up or worn out brushes in the motor.
>
> You 'might' be able to open it and hit up a (starter) motor rebuilder
> for a set of brushes. That's what I do when my starter acts like that.
> (needing a hit to set the brushes again) My XJ starter's brush pack set
> me back about $15.00 if I remember right.
>
> Or you could be lucky and only need some WD40 to clean out the dust that
> mixed with the grease to gum up the brushes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> D wrote:
>>
>> And an update.
>> Got the scissor rack out, along with the motor and gear assembly. I
>> remember
>> this setup now as it about took my thumb off a few years ago when I
>> unbolted
>> the motor from the housing. There's a powerful spring there.
>> Anyway, I hooked it all up electrically outside the door and tried it.
>> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
>> strongly now.
>> Any bets on how long it will last now? Hopefully for another month when
>> my
>> raise kicks in and I can trade the old gal in on an '01 or '02. She's
>> getting to be too much for me.
>> Thanks all for your help and support.
>> D
>>
>> "DougW" <post.replies@invalid.address> wrote in message
>> news:1Dgtg.66419$9c6.43085@dukeread11...
>> > "D" wrote ...
>> > > Hi All,
>> > > The window went down in the driver door and wont go back up. Power to
>> > > it
>> > > okay.
>> > > Is there a web site that shows picks of the regulator, et-al so I can
>> clean
>> > > it up? Maybe make it work for a little while longer?
>> > > I'll be putting the switch back together as I wait for an answer.
>> > > Heh.
>> >
>> > Take the door panel off (watch the edges they are very sharp)
>> > then look at the plastic connector that snaps to the power window
>> > switch assembly. Odds are it has come unhooked. The way that
>> > switch works if the motor has power then it has to be the switch
>> > or the connector. The one on my passenger side broke and I had
>> > to put a zip-tie in to hold it on.
>> >
>> > --
>> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
>> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
>> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
>> > Banks Header - and BEER, in the fridge!
>> >
>> >
07-13-2006, 12:31 PM
#29
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
For starters, I use WD40. It works well and is inexpensive. I save the
contact cleaner for the plug contacts....
Mike
c wrote:
>
> If it is crud in there, I would recommend using the electrical contact spray
> cleaner. Car-Quest has one here that is called extra strength, and it works
> great. I was sold on it after using it to clean a blower motor on a
> commercial deep fryer. Many years of dust and grease came clean with no
> effort at all. I'm sure most of the spray cleaners are about the same, but I
> know this stuff worked great.
>
> Chris
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44B66052.5B106C21@sympatico.ca...
> > You are describing either gummed up or worn out brushes in the motor.
> >
> > You 'might' be able to open it and hit up a (starter) motor rebuilder
> > for a set of brushes. That's what I do when my starter acts like that.
> > (needing a hit to set the brushes again) My XJ starter's brush pack set
> > me back about $15.00 if I remember right.
> >
> > Or you could be lucky and only need some WD40 to clean out the dust that
> > mixed with the grease to gum up the brushes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > D wrote:
> >>
> >> And an update.
> >> Got the scissor rack out, along with the motor and gear assembly. I
> >> remember
> >> this setup now as it about took my thumb off a few years ago when I
> >> unbolted
> >> the motor from the housing. There's a powerful spring there.
> >> Anyway, I hooked it all up electrically outside the door and tried it.
> >> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> >> strongly now.
> >> Any bets on how long it will last now? Hopefully for another month when
> >> my
> >> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> >> getting to be too much for me.
> >> Thanks all for your help and support.
> >> D
> >>
> >> "DougW" <post.replies@invalid.address> wrote in message
> >> news:1Dgtg.66419$9c6.43085@dukeread11...
> >> > "D" wrote ...
> >> > > Hi All,
> >> > > The window went down in the driver door and wont go back up. Power to
> >> > > it
> >> > > okay.
> >> > > Is there a web site that shows picks of the regulator, et-al so I can
> >> clean
> >> > > it up? Maybe make it work for a little while longer?
> >> > > I'll be putting the switch back together as I wait for an answer.
> >> > > Heh.
> >> >
> >> > Take the door panel off (watch the edges they are very sharp)
> >> > then look at the plastic connector that snaps to the power window
> >> > switch assembly. Odds are it has come unhooked. The way that
> >> > switch works if the motor has power then it has to be the switch
> >> > or the connector. The one on my passenger side broke and I had
> >> > to put a zip-tie in to hold it on.
> >> >
> >> > --
> >> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> >> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> >> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> >> > Banks Header - and BEER, in the fridge!
> >> >
> >> >
contact cleaner for the plug contacts....
Mike
c wrote:
>
> If it is crud in there, I would recommend using the electrical contact spray
> cleaner. Car-Quest has one here that is called extra strength, and it works
> great. I was sold on it after using it to clean a blower motor on a
> commercial deep fryer. Many years of dust and grease came clean with no
> effort at all. I'm sure most of the spray cleaners are about the same, but I
> know this stuff worked great.
>
> Chris
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44B66052.5B106C21@sympatico.ca...
> > You are describing either gummed up or worn out brushes in the motor.
> >
> > You 'might' be able to open it and hit up a (starter) motor rebuilder
> > for a set of brushes. That's what I do when my starter acts like that.
> > (needing a hit to set the brushes again) My XJ starter's brush pack set
> > me back about $15.00 if I remember right.
> >
> > Or you could be lucky and only need some WD40 to clean out the dust that
> > mixed with the grease to gum up the brushes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > D wrote:
> >>
> >> And an update.
> >> Got the scissor rack out, along with the motor and gear assembly. I
> >> remember
> >> this setup now as it about took my thumb off a few years ago when I
> >> unbolted
> >> the motor from the housing. There's a powerful spring there.
> >> Anyway, I hooked it all up electrically outside the door and tried it.
> >> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> >> strongly now.
> >> Any bets on how long it will last now? Hopefully for another month when
> >> my
> >> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> >> getting to be too much for me.
> >> Thanks all for your help and support.
> >> D
> >>
> >> "DougW" <post.replies@invalid.address> wrote in message
> >> news:1Dgtg.66419$9c6.43085@dukeread11...
> >> > "D" wrote ...
> >> > > Hi All,
> >> > > The window went down in the driver door and wont go back up. Power to
> >> > > it
> >> > > okay.
> >> > > Is there a web site that shows picks of the regulator, et-al so I can
> >> clean
> >> > > it up? Maybe make it work for a little while longer?
> >> > > I'll be putting the switch back together as I wait for an answer.
> >> > > Heh.
> >> >
> >> > Take the door panel off (watch the edges they are very sharp)
> >> > then look at the plastic connector that snaps to the power window
> >> > switch assembly. Odds are it has come unhooked. The way that
> >> > switch works if the motor has power then it has to be the switch
> >> > or the connector. The one on my passenger side broke and I had
> >> > to put a zip-tie in to hold it on.
> >> >
> >> > --
> >> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> >> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> >> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> >> > Banks Header - and BEER, in the fridge!
> >> >
> >> >
07-13-2006, 12:31 PM
#30
Guest
Posts: n/a
Re: 93 Grand Cherokee Power Window
For starters, I use WD40. It works well and is inexpensive. I save the
contact cleaner for the plug contacts....
Mike
c wrote:
>
> If it is crud in there, I would recommend using the electrical contact spray
> cleaner. Car-Quest has one here that is called extra strength, and it works
> great. I was sold on it after using it to clean a blower motor on a
> commercial deep fryer. Many years of dust and grease came clean with no
> effort at all. I'm sure most of the spray cleaners are about the same, but I
> know this stuff worked great.
>
> Chris
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44B66052.5B106C21@sympatico.ca...
> > You are describing either gummed up or worn out brushes in the motor.
> >
> > You 'might' be able to open it and hit up a (starter) motor rebuilder
> > for a set of brushes. That's what I do when my starter acts like that.
> > (needing a hit to set the brushes again) My XJ starter's brush pack set
> > me back about $15.00 if I remember right.
> >
> > Or you could be lucky and only need some WD40 to clean out the dust that
> > mixed with the grease to gum up the brushes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > D wrote:
> >>
> >> And an update.
> >> Got the scissor rack out, along with the motor and gear assembly. I
> >> remember
> >> this setup now as it about took my thumb off a few years ago when I
> >> unbolted
> >> the motor from the housing. There's a powerful spring there.
> >> Anyway, I hooked it all up electrically outside the door and tried it.
> >> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> >> strongly now.
> >> Any bets on how long it will last now? Hopefully for another month when
> >> my
> >> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> >> getting to be too much for me.
> >> Thanks all for your help and support.
> >> D
> >>
> >> "DougW" <post.replies@invalid.address> wrote in message
> >> news:1Dgtg.66419$9c6.43085@dukeread11...
> >> > "D" wrote ...
> >> > > Hi All,
> >> > > The window went down in the driver door and wont go back up. Power to
> >> > > it
> >> > > okay.
> >> > > Is there a web site that shows picks of the regulator, et-al so I can
> >> clean
> >> > > it up? Maybe make it work for a little while longer?
> >> > > I'll be putting the switch back together as I wait for an answer.
> >> > > Heh.
> >> >
> >> > Take the door panel off (watch the edges they are very sharp)
> >> > then look at the plastic connector that snaps to the power window
> >> > switch assembly. Odds are it has come unhooked. The way that
> >> > switch works if the motor has power then it has to be the switch
> >> > or the connector. The one on my passenger side broke and I had
> >> > to put a zip-tie in to hold it on.
> >> >
> >> > --
> >> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> >> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> >> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> >> > Banks Header - and BEER, in the fridge!
> >> >
> >> >
contact cleaner for the plug contacts....
Mike
c wrote:
>
> If it is crud in there, I would recommend using the electrical contact spray
> cleaner. Car-Quest has one here that is called extra strength, and it works
> great. I was sold on it after using it to clean a blower motor on a
> commercial deep fryer. Many years of dust and grease came clean with no
> effort at all. I'm sure most of the spray cleaners are about the same, but I
> know this stuff worked great.
>
> Chris
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44B66052.5B106C21@sympatico.ca...
> > You are describing either gummed up or worn out brushes in the motor.
> >
> > You 'might' be able to open it and hit up a (starter) motor rebuilder
> > for a set of brushes. That's what I do when my starter acts like that.
> > (needing a hit to set the brushes again) My XJ starter's brush pack set
> > me back about $15.00 if I remember right.
> >
> > Or you could be lucky and only need some WD40 to clean out the dust that
> > mixed with the grease to gum up the brushes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > D wrote:
> >>
> >> And an update.
> >> Got the scissor rack out, along with the motor and gear assembly. I
> >> remember
> >> this setup now as it about took my thumb off a few years ago when I
> >> unbolted
> >> the motor from the housing. There's a powerful spring there.
> >> Anyway, I hooked it all up electrically outside the door and tried it.
> >> Nothing. Tapped on the motor housing and 'poof' it works smoothly and
> >> strongly now.
> >> Any bets on how long it will last now? Hopefully for another month when
> >> my
> >> raise kicks in and I can trade the old gal in on an '01 or '02. She's
> >> getting to be too much for me.
> >> Thanks all for your help and support.
> >> D
> >>
> >> "DougW" <post.replies@invalid.address> wrote in message
> >> news:1Dgtg.66419$9c6.43085@dukeread11...
> >> > "D" wrote ...
> >> > > Hi All,
> >> > > The window went down in the driver door and wont go back up. Power to
> >> > > it
> >> > > okay.
> >> > > Is there a web site that shows picks of the regulator, et-al so I can
> >> clean
> >> > > it up? Maybe make it work for a little while longer?
> >> > > I'll be putting the switch back together as I wait for an answer.
> >> > > Heh.
> >> >
> >> > Take the door panel off (watch the edges they are very sharp)
> >> > then look at the plastic connector that snaps to the power window
> >> > switch assembly. Odds are it has come unhooked. The way that
> >> > switch works if the motor has power then it has to be the switch
> >> > or the connector. The one on my passenger side broke and I had
> >> > to put a zip-tie in to hold it on.
> >> >
> >> > --
> >> > -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> >> > HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> >> > Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> >> > Banks Header - and BEER, in the fridge!
> >> >
> >> >