Don't foerget the Mazda Wankel rotary:
http://www.rotaryengineillustrated.com/animations.php

"Dave Milne" <whoneeds@toknow.com> wrote in message
news:SooMg.16060$r61.2875@text.news.blueyonder.co. uk...
> Alfa Romeo have been using "twin spark" engines as they call them, since
> the
> 60's (and still use them today).
> I had the 3.0 v6 hemi which was conventional - they only did them on the 4
> cylinder models which ran up to 2 litres.
>
> Dave Milne, Scotland
>
> "Lon" <lon.stowell@comcast.net> wrote in message
> news:a5CdnXQWXs0PTp3YnZ2dnUVZ_tSdnZ2d@comcast.com. ..
>
>> Dual points worked, dual plugs worked even better but dunno anyone using
>> them since the old straight 8 Nash engines of the late 30's.
>
>

 

A 1934 Nash with dual plugs, the other eight are on the carburetor
side: http://www.vapinc.com/1934nashrestor...2/PIC00004.jpg
And of course Top Fuel use two:
http://www.----------.com/temp/DickLaHaie.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Dave Milne wrote:
>
> Alfa Romeo have been using "twin spark" engines as they call them, since the
> 60's (and still use them today).
> I had the 3.0 v6 hemi which was conventional - they only did them on the 4
> cylinder models which ran up to 2 litres.
>
> Dave Milne, Scotland

 

A 1934 Nash with dual plugs, the other eight are on the carburetor
side: http://www.vapinc.com/1934nashrestor...2/PIC00004.jpg
And of course Top Fuel use two:
http://www.----------.com/temp/DickLaHaie.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Dave Milne wrote:
>
> Alfa Romeo have been using "twin spark" engines as they call them, since the
> 60's (and still use them today).
> I had the 3.0 v6 hemi which was conventional - they only did them on the 4
> cylinder models which ran up to 2 litres.
>
> Dave Milne, Scotland

 

A 1934 Nash with dual plugs, the other eight are on the carburetor
side: http://www.vapinc.com/1934nashrestor...2/PIC00004.jpg
And of course Top Fuel use two:
http://www.----------.com/temp/DickLaHaie.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Dave Milne wrote:
>
> Alfa Romeo have been using "twin spark" engines as they call them, since the
> 60's (and still use them today).
> I had the 3.0 v6 hemi which was conventional - they only did them on the 4
> cylinder models which ran up to 2 litres.
>
> Dave Milne, Scotland

 

Sounds like a good purchase - will order and wait 3 weeks for it to arrive
(!).

Got it fitted at the weekend, relatively painlessly. Well, I mean that
metaphorically actually, as I cut the hell out of my thumb as I was putting
on the valley pan gasket with blood going everywhere and trying to keep it
off the RTV. So now the nastier bits of the emissions control are
disconnected (the EGR and the air injection stuff). As it is now not really
an emssions controlled vehicle, I attached it to the non-timed part of the
carb per the instructions, but that gave me 34 degrees BTDC, so plugged it
into the timed-port and got a more sensible 10 degrees BTDC. Gas analyser
was playing up a bit, so I'll do the tuning next weekend, but even on the
default settings, it is pulling way more strongly than it ever did before -
can't be far off.

Oh, Edelbrock's instructions in the 2131 manifold state that the Performer
1405 requires a Square bore to ------ bore adapter. Except that both carb
and manifold are square bore already, and I hadn't ordered one. Doesn't
seem to mention the need for it anywhere else - will drop them a line to
check that it is a mistake on their part. Certainly seems to run fine
without it.

Dave Milne, Scotland


"c" <c@me.org> wrote in message
news:RjPLg.1352$d72.768@tornado.rdc-kc.rr.com...
> Dave, you shouldn't have a problem tuning the Carter/Edelbrock carb, and
> yes, they are basically the same carb inside. I believe the jets and rods
> interchange, but I'm not positive on that. I do know that the Edelbrock
carb
> is heavily based on the Carter design. If you understand basic carb
> functioning, and what the rods and jets do for the mixture, it will be a
> simple process to get it dialed in. If you ruin in to problems, I'm sure
we
> can get you going in the right direction. Also, there is a book available
> called Carter Carb Tuning. Most of it will apply to the Edelbrock as well.
I
> had the book at one time, but loaned it out and never got it back. I do
know
> that the book is very thorough.
>
> Chris
>
>
> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> news:FiGLg.14805$r61.8273@text.news.blueyonder.co. uk...
> > Thanks. Looks like perhaps I should have ordered the calibration kit in
> > retrospect. Anyhow, after a 2 week wait, it has arrived so I'll fit at
the
> > weekend.
> >
> > Quite looking forward to it - my carb experience has been mainly with
> > multiple SU's (single barrel downdraft) and the odd side draft Weber -
> > never done anything on a 4 barrel like Holley or Edelbrock before.
> >
> > Dave Milne, Scotland
> > '91 Grand Wagoneer, '99 TJ
> > "c" <c@me.org> wrote in message
> > news:1lDLg.1336$d72.134@tornado.rdc-kc.rr.com...
> >> Dave,
> >>
> >> When the companies that make carb give them their initial settings from
> > the
> >> factory, they take all kinds of compromised in to consideration. They
> > don't
> >> know if the carb will be used on a large or small displacement engine,
or
> > if
> >> it will be used in hot or cold climate, high altitude, etc. They also
> > don't
> >> know what other mods have been done to these engines. The baseline
> > settings
> >> they give these carbs will allow them to run on most of the
applications
> >> they will see, but they almost always require tuning to get them to be
> >> optimal. My guess would be that this carb would still be a little rich,
> > but
> >> it is just a guess. I'm not saying it won't run, it will, and it will
> >> probably be pretty damn close to right.
> >>
> >> The metering rod system that Carter/Edelbrock uses will "adjust" the
> > mixture
> >> based on engine vacuum. The rods are controlled by a piston and spring,
> >> similar to many other carbs. When the engine vacuum is low, the
metering
> > rod
> >> spring will start to overtake the vacuum pulling the piston down. The
> >> rods
> >> are tapered, and when they move up in the bore they are in, a smaller
> >> diameter of the rod will still be inside the main jet, effectively
> >> increasing the total main jet area that fuel can pass thru. If the
engine
> >> runs too rich at high vacuum conditions, but is ok at low vacuum or
wide
> >> open throttle, then you simply change the metering rod to on the has a
> >> larger diameter on the part of the rod that is in the jet at high
vacuum
> >> conditions. It really is a simple process, and normally will only
require
> > 1
> >> or 2 sets of rods to get the carb where you need it to be.
> >>
> >> Chris
> >>
> >>
> >> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> >> news:OeuLg.14311$r61.1621@text.news.blueyonder.co. uk...
> >> > Any idea if the Edelbrock 600cfm 1405 Performer + Edelbrock 2131
> > manifold
> >> > will require a metering or jet change on a stock 360 '91 Grand
Wagoneer
> > ?
> >> >
> >> >
> >> > Dave Milne, Scotland
> >> > '91 Grand Wagoneer, '99 TJ
> >> > "c" <c@me.org> wrote in message
> >> > news:cliLg.1294$d72.56@tornado.rdc-kc.rr.com...
> >> >> Without knowing what size carb, choke or no choke, and which
manifold,
> > it
> >> > is
> >> >> hard to tell you what the problem could be. What I can tell you is
> >> >> that
> >> >> Edelbrock and Holley carbs are both set up from the factory with a
> >> >> general
> >> >> tune. This mean the carb may or may not need to be set up properly
for
> >> > your
> >> >> particular engine. In general, the Edelbrock carbs run too rich with
> > the
> >> >> factory set up. Normally they will require a metering rod change,
and
> >> > maybe
> >> >> a jet change as well. You also don't specify the cam specs.
> >> >
> >> >
> >> >
> >>
> >>
> >
> >
>
>

 

Sounds like a good purchase - will order and wait 3 weeks for it to arrive
(!).

Got it fitted at the weekend, relatively painlessly. Well, I mean that
metaphorically actually, as I cut the hell out of my thumb as I was putting
on the valley pan gasket with blood going everywhere and trying to keep it
off the RTV. So now the nastier bits of the emissions control are
disconnected (the EGR and the air injection stuff). As it is now not really
an emssions controlled vehicle, I attached it to the non-timed part of the
carb per the instructions, but that gave me 34 degrees BTDC, so plugged it
into the timed-port and got a more sensible 10 degrees BTDC. Gas analyser
was playing up a bit, so I'll do the tuning next weekend, but even on the
default settings, it is pulling way more strongly than it ever did before -
can't be far off.

Oh, Edelbrock's instructions in the 2131 manifold state that the Performer
1405 requires a Square bore to ------ bore adapter. Except that both carb
and manifold are square bore already, and I hadn't ordered one. Doesn't
seem to mention the need for it anywhere else - will drop them a line to
check that it is a mistake on their part. Certainly seems to run fine
without it.

Dave Milne, Scotland


"c" <c@me.org> wrote in message
news:RjPLg.1352$d72.768@tornado.rdc-kc.rr.com...
> Dave, you shouldn't have a problem tuning the Carter/Edelbrock carb, and
> yes, they are basically the same carb inside. I believe the jets and rods
> interchange, but I'm not positive on that. I do know that the Edelbrock
carb
> is heavily based on the Carter design. If you understand basic carb
> functioning, and what the rods and jets do for the mixture, it will be a
> simple process to get it dialed in. If you ruin in to problems, I'm sure
we
> can get you going in the right direction. Also, there is a book available
> called Carter Carb Tuning. Most of it will apply to the Edelbrock as well.
I
> had the book at one time, but loaned it out and never got it back. I do
know
> that the book is very thorough.
>
> Chris
>
>
> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> news:FiGLg.14805$r61.8273@text.news.blueyonder.co. uk...
> > Thanks. Looks like perhaps I should have ordered the calibration kit in
> > retrospect. Anyhow, after a 2 week wait, it has arrived so I'll fit at
the
> > weekend.
> >
> > Quite looking forward to it - my carb experience has been mainly with
> > multiple SU's (single barrel downdraft) and the odd side draft Weber -
> > never done anything on a 4 barrel like Holley or Edelbrock before.
> >
> > Dave Milne, Scotland
> > '91 Grand Wagoneer, '99 TJ
> > "c" <c@me.org> wrote in message
> > news:1lDLg.1336$d72.134@tornado.rdc-kc.rr.com...
> >> Dave,
> >>
> >> When the companies that make carb give them their initial settings from
> > the
> >> factory, they take all kinds of compromised in to consideration. They
> > don't
> >> know if the carb will be used on a large or small displacement engine,
or
> > if
> >> it will be used in hot or cold climate, high altitude, etc. They also
> > don't
> >> know what other mods have been done to these engines. The baseline
> > settings
> >> they give these carbs will allow them to run on most of the
applications
> >> they will see, but they almost always require tuning to get them to be
> >> optimal. My guess would be that this carb would still be a little rich,
> > but
> >> it is just a guess. I'm not saying it won't run, it will, and it will
> >> probably be pretty damn close to right.
> >>
> >> The metering rod system that Carter/Edelbrock uses will "adjust" the
> > mixture
> >> based on engine vacuum. The rods are controlled by a piston and spring,
> >> similar to many other carbs. When the engine vacuum is low, the
metering
> > rod
> >> spring will start to overtake the vacuum pulling the piston down. The
> >> rods
> >> are tapered, and when they move up in the bore they are in, a smaller
> >> diameter of the rod will still be inside the main jet, effectively
> >> increasing the total main jet area that fuel can pass thru. If the
engine
> >> runs too rich at high vacuum conditions, but is ok at low vacuum or
wide
> >> open throttle, then you simply change the metering rod to on the has a
> >> larger diameter on the part of the rod that is in the jet at high
vacuum
> >> conditions. It really is a simple process, and normally will only
require
> > 1
> >> or 2 sets of rods to get the carb where you need it to be.
> >>
> >> Chris
> >>
> >>
> >> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> >> news:OeuLg.14311$r61.1621@text.news.blueyonder.co. uk...
> >> > Any idea if the Edelbrock 600cfm 1405 Performer + Edelbrock 2131
> > manifold
> >> > will require a metering or jet change on a stock 360 '91 Grand
Wagoneer
> > ?
> >> >
> >> >
> >> > Dave Milne, Scotland
> >> > '91 Grand Wagoneer, '99 TJ
> >> > "c" <c@me.org> wrote in message
> >> > news:cliLg.1294$d72.56@tornado.rdc-kc.rr.com...
> >> >> Without knowing what size carb, choke or no choke, and which
manifold,
> > it
> >> > is
> >> >> hard to tell you what the problem could be. What I can tell you is
> >> >> that
> >> >> Edelbrock and Holley carbs are both set up from the factory with a
> >> >> general
> >> >> tune. This mean the carb may or may not need to be set up properly
for
> >> > your
> >> >> particular engine. In general, the Edelbrock carbs run too rich with
> > the
> >> >> factory set up. Normally they will require a metering rod change,
and
> >> > maybe
> >> >> a jet change as well. You also don't specify the cam specs.
> >> >
> >> >
> >> >
> >>
> >>
> >
> >
>
>

 

Sounds like a good purchase - will order and wait 3 weeks for it to arrive
(!).

Got it fitted at the weekend, relatively painlessly. Well, I mean that
metaphorically actually, as I cut the hell out of my thumb as I was putting
on the valley pan gasket with blood going everywhere and trying to keep it
off the RTV. So now the nastier bits of the emissions control are
disconnected (the EGR and the air injection stuff). As it is now not really
an emssions controlled vehicle, I attached it to the non-timed part of the
carb per the instructions, but that gave me 34 degrees BTDC, so plugged it
into the timed-port and got a more sensible 10 degrees BTDC. Gas analyser
was playing up a bit, so I'll do the tuning next weekend, but even on the
default settings, it is pulling way more strongly than it ever did before -
can't be far off.

Oh, Edelbrock's instructions in the 2131 manifold state that the Performer
1405 requires a Square bore to ------ bore adapter. Except that both carb
and manifold are square bore already, and I hadn't ordered one. Doesn't
seem to mention the need for it anywhere else - will drop them a line to
check that it is a mistake on their part. Certainly seems to run fine
without it.

Dave Milne, Scotland


"c" <c@me.org> wrote in message
news:RjPLg.1352$d72.768@tornado.rdc-kc.rr.com...
> Dave, you shouldn't have a problem tuning the Carter/Edelbrock carb, and
> yes, they are basically the same carb inside. I believe the jets and rods
> interchange, but I'm not positive on that. I do know that the Edelbrock
carb
> is heavily based on the Carter design. If you understand basic carb
> functioning, and what the rods and jets do for the mixture, it will be a
> simple process to get it dialed in. If you ruin in to problems, I'm sure
we
> can get you going in the right direction. Also, there is a book available
> called Carter Carb Tuning. Most of it will apply to the Edelbrock as well.
I
> had the book at one time, but loaned it out and never got it back. I do
know
> that the book is very thorough.
>
> Chris
>
>
> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> news:FiGLg.14805$r61.8273@text.news.blueyonder.co. uk...
> > Thanks. Looks like perhaps I should have ordered the calibration kit in
> > retrospect. Anyhow, after a 2 week wait, it has arrived so I'll fit at
the
> > weekend.
> >
> > Quite looking forward to it - my carb experience has been mainly with
> > multiple SU's (single barrel downdraft) and the odd side draft Weber -
> > never done anything on a 4 barrel like Holley or Edelbrock before.
> >
> > Dave Milne, Scotland
> > '91 Grand Wagoneer, '99 TJ
> > "c" <c@me.org> wrote in message
> > news:1lDLg.1336$d72.134@tornado.rdc-kc.rr.com...
> >> Dave,
> >>
> >> When the companies that make carb give them their initial settings from
> > the
> >> factory, they take all kinds of compromised in to consideration. They
> > don't
> >> know if the carb will be used on a large or small displacement engine,
or
> > if
> >> it will be used in hot or cold climate, high altitude, etc. They also
> > don't
> >> know what other mods have been done to these engines. The baseline
> > settings
> >> they give these carbs will allow them to run on most of the
applications
> >> they will see, but they almost always require tuning to get them to be
> >> optimal. My guess would be that this carb would still be a little rich,
> > but
> >> it is just a guess. I'm not saying it won't run, it will, and it will
> >> probably be pretty damn close to right.
> >>
> >> The metering rod system that Carter/Edelbrock uses will "adjust" the
> > mixture
> >> based on engine vacuum. The rods are controlled by a piston and spring,
> >> similar to many other carbs. When the engine vacuum is low, the
metering
> > rod
> >> spring will start to overtake the vacuum pulling the piston down. The
> >> rods
> >> are tapered, and when they move up in the bore they are in, a smaller
> >> diameter of the rod will still be inside the main jet, effectively
> >> increasing the total main jet area that fuel can pass thru. If the
engine
> >> runs too rich at high vacuum conditions, but is ok at low vacuum or
wide
> >> open throttle, then you simply change the metering rod to on the has a
> >> larger diameter on the part of the rod that is in the jet at high
vacuum
> >> conditions. It really is a simple process, and normally will only
require
> > 1
> >> or 2 sets of rods to get the carb where you need it to be.
> >>
> >> Chris
> >>
> >>
> >> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> >> news:OeuLg.14311$r61.1621@text.news.blueyonder.co. uk...
> >> > Any idea if the Edelbrock 600cfm 1405 Performer + Edelbrock 2131
> > manifold
> >> > will require a metering or jet change on a stock 360 '91 Grand
Wagoneer
> > ?
> >> >
> >> >
> >> > Dave Milne, Scotland
> >> > '91 Grand Wagoneer, '99 TJ
> >> > "c" <c@me.org> wrote in message
> >> > news:cliLg.1294$d72.56@tornado.rdc-kc.rr.com...
> >> >> Without knowing what size carb, choke or no choke, and which
manifold,
> > it
> >> > is
> >> >> hard to tell you what the problem could be. What I can tell you is
> >> >> that
> >> >> Edelbrock and Holley carbs are both set up from the factory with a
> >> >> general
> >> >> tune. This mean the carb may or may not need to be set up properly
for
> >> > your
> >> >> particular engine. In general, the Edelbrock carbs run too rich with
> > the
> >> >> factory set up. Normally they will require a metering rod change,
and
> >> > maybe
> >> >> a jet change as well. You also don't specify the cam specs.
> >> >
> >> >
> >> >
> >>
> >>
> >
> >
>
>

 

Dave,

It would be a shame to install less restrictive intake components, without
similar changes to the exhaust.

Earle

"Dave Milne" <whoneeds@toknow.com> wrote in message
news:D6_Mg.16900$r61.754@text.news.blueyonder.co.u k...
> Sounds like a good purchase - will order and wait 3 weeks for it to arrive
> (!).
>
> Got it fitted at the weekend, relatively painlessly. Well, I mean that
> metaphorically actually, as I cut the hell out of my thumb as I was
putting
> on the valley pan gasket with blood going everywhere and trying to keep it
> off the RTV. So now the nastier bits of the emissions control are
> disconnected (the EGR and the air injection stuff). As it is now not
really
> an emssions controlled vehicle, I attached it to the non-timed part of the
> carb per the instructions, but that gave me 34 degrees BTDC, so plugged it
> into the timed-port and got a more sensible 10 degrees BTDC. Gas analyser
> was playing up a bit, so I'll do the tuning next weekend, but even on the
> default settings, it is pulling way more strongly than it ever did
before -
> can't be far off.
>
> Oh, Edelbrock's instructions in the 2131 manifold state that the Performer
> 1405 requires a Square bore to ------ bore adapter. Except that both carb
> and manifold are square bore already, and I hadn't ordered one. Doesn't
> seem to mention the need for it anywhere else - will drop them a line to
> check that it is a mistake on their part. Certainly seems to run fine
> without it.
>
> Dave Milne, Scotland
>
>
> "c" <c@me.org> wrote in message
> news:RjPLg.1352$d72.768@tornado.rdc-kc.rr.com...
> > Dave, you shouldn't have a problem tuning the Carter/Edelbrock carb, and
> > yes, they are basically the same carb inside. I believe the jets and
rods
> > interchange, but I'm not positive on that. I do know that the Edelbrock
> carb
> > is heavily based on the Carter design. If you understand basic carb
> > functioning, and what the rods and jets do for the mixture, it will be a
> > simple process to get it dialed in. If you ruin in to problems, I'm sure
> we
> > can get you going in the right direction. Also, there is a book
available
> > called Carter Carb Tuning. Most of it will apply to the Edelbrock as
well.
> I
> > had the book at one time, but loaned it out and never got it back. I do
> know
> > that the book is very thorough.
> >
> > Chris
> >
> >
> > "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> > news:FiGLg.14805$r61.8273@text.news.blueyonder.co. uk...
> > > Thanks. Looks like perhaps I should have ordered the calibration kit
in
> > > retrospect. Anyhow, after a 2 week wait, it has arrived so I'll fit at
> the
> > > weekend.
> > >
> > > Quite looking forward to it - my carb experience has been mainly with
> > > multiple SU's (single barrel downdraft) and the odd side draft
Weber -
> > > never done anything on a 4 barrel like Holley or Edelbrock before.
> > >
> > > Dave Milne, Scotland
> > > '91 Grand Wagoneer, '99 TJ
> > > "c" <c@me.org> wrote in message
> > > news:1lDLg.1336$d72.134@tornado.rdc-kc.rr.com...
> > >> Dave,
> > >>
> > >> When the companies that make carb give them their initial settings
from
> > > the
> > >> factory, they take all kinds of compromised in to consideration. They
> > > don't
> > >> know if the carb will be used on a large or small displacement
engine,
> or
> > > if
> > >> it will be used in hot or cold climate, high altitude, etc. They also
> > > don't
> > >> know what other mods have been done to these engines. The baseline
> > > settings
> > >> they give these carbs will allow them to run on most of the
> applications
> > >> they will see, but they almost always require tuning to get them to
be
> > >> optimal. My guess would be that this carb would still be a little
rich,
> > > but
> > >> it is just a guess. I'm not saying it won't run, it will, and it will
> > >> probably be pretty damn close to right.
> > >>
> > >> The metering rod system that Carter/Edelbrock uses will "adjust" the
> > > mixture
> > >> based on engine vacuum. The rods are controlled by a piston and
spring,
> > >> similar to many other carbs. When the engine vacuum is low, the
> metering
> > > rod
> > >> spring will start to overtake the vacuum pulling the piston down. The
> > >> rods
> > >> are tapered, and when they move up in the bore they are in, a smaller
> > >> diameter of the rod will still be inside the main jet, effectively
> > >> increasing the total main jet area that fuel can pass thru. If the
> engine
> > >> runs too rich at high vacuum conditions, but is ok at low vacuum or
> wide
> > >> open throttle, then you simply change the metering rod to on the has
a
> > >> larger diameter on the part of the rod that is in the jet at high
> vacuum
> > >> conditions. It really is a simple process, and normally will only
> require
> > > 1
> > >> or 2 sets of rods to get the carb where you need it to be.
> > >>
> > >> Chris
> > >>
> > >>
> > >> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> > >> news:OeuLg.14311$r61.1621@text.news.blueyonder.co. uk...
> > >> > Any idea if the Edelbrock 600cfm 1405 Performer + Edelbrock 2131
> > > manifold
> > >> > will require a metering or jet change on a stock 360 '91 Grand
> Wagoneer
> > > ?
> > >> >
> > >> >
> > >> > Dave Milne, Scotland
> > >> > '91 Grand Wagoneer, '99 TJ
> > >> > "c" <c@me.org> wrote in message
> > >> > news:cliLg.1294$d72.56@tornado.rdc-kc.rr.com...
> > >> >> Without knowing what size carb, choke or no choke, and which
> manifold,
> > > it
> > >> > is
> > >> >> hard to tell you what the problem could be. What I can tell you is
> > >> >> that
> > >> >> Edelbrock and Holley carbs are both set up from the factory with a
> > >> >> general
> > >> >> tune. This mean the carb may or may not need to be set up properly
> for
> > >> > your
> > >> >> particular engine. In general, the Edelbrock carbs run too rich
with
> > > the
> > >> >> factory set up. Normally they will require a metering rod change,
> and
> > >> > maybe
> > >> >> a jet change as well. You also don't specify the cam specs.
> > >> >
> > >> >
> > >> >
> > >>
> > >>
> > >
> > >
> >
> >
>
>

 

Dave,

It would be a shame to install less restrictive intake components, without
similar changes to the exhaust.

Earle

"Dave Milne" <whoneeds@toknow.com> wrote in message
news:D6_Mg.16900$r61.754@text.news.blueyonder.co.u k...
> Sounds like a good purchase - will order and wait 3 weeks for it to arrive
> (!).
>
> Got it fitted at the weekend, relatively painlessly. Well, I mean that
> metaphorically actually, as I cut the hell out of my thumb as I was
putting
> on the valley pan gasket with blood going everywhere and trying to keep it
> off the RTV. So now the nastier bits of the emissions control are
> disconnected (the EGR and the air injection stuff). As it is now not
really
> an emssions controlled vehicle, I attached it to the non-timed part of the
> carb per the instructions, but that gave me 34 degrees BTDC, so plugged it
> into the timed-port and got a more sensible 10 degrees BTDC. Gas analyser
> was playing up a bit, so I'll do the tuning next weekend, but even on the
> default settings, it is pulling way more strongly than it ever did
before -
> can't be far off.
>
> Oh, Edelbrock's instructions in the 2131 manifold state that the Performer
> 1405 requires a Square bore to ------ bore adapter. Except that both carb
> and manifold are square bore already, and I hadn't ordered one. Doesn't
> seem to mention the need for it anywhere else - will drop them a line to
> check that it is a mistake on their part. Certainly seems to run fine
> without it.
>
> Dave Milne, Scotland
>
>
> "c" <c@me.org> wrote in message
> news:RjPLg.1352$d72.768@tornado.rdc-kc.rr.com...
> > Dave, you shouldn't have a problem tuning the Carter/Edelbrock carb, and
> > yes, they are basically the same carb inside. I believe the jets and
rods
> > interchange, but I'm not positive on that. I do know that the Edelbrock
> carb
> > is heavily based on the Carter design. If you understand basic carb
> > functioning, and what the rods and jets do for the mixture, it will be a
> > simple process to get it dialed in. If you ruin in to problems, I'm sure
> we
> > can get you going in the right direction. Also, there is a book
available
> > called Carter Carb Tuning. Most of it will apply to the Edelbrock as
well.
> I
> > had the book at one time, but loaned it out and never got it back. I do
> know
> > that the book is very thorough.
> >
> > Chris
> >
> >
> > "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> > news:FiGLg.14805$r61.8273@text.news.blueyonder.co. uk...
> > > Thanks. Looks like perhaps I should have ordered the calibration kit
in
> > > retrospect. Anyhow, after a 2 week wait, it has arrived so I'll fit at
> the
> > > weekend.
> > >
> > > Quite looking forward to it - my carb experience has been mainly with
> > > multiple SU's (single barrel downdraft) and the odd side draft
Weber -
> > > never done anything on a 4 barrel like Holley or Edelbrock before.
> > >
> > > Dave Milne, Scotland
> > > '91 Grand Wagoneer, '99 TJ
> > > "c" <c@me.org> wrote in message
> > > news:1lDLg.1336$d72.134@tornado.rdc-kc.rr.com...
> > >> Dave,
> > >>
> > >> When the companies that make carb give them their initial settings
from
> > > the
> > >> factory, they take all kinds of compromised in to consideration. They
> > > don't
> > >> know if the carb will be used on a large or small displacement
engine,
> or
> > > if
> > >> it will be used in hot or cold climate, high altitude, etc. They also
> > > don't
> > >> know what other mods have been done to these engines. The baseline
> > > settings
> > >> they give these carbs will allow them to run on most of the
> applications
> > >> they will see, but they almost always require tuning to get them to
be
> > >> optimal. My guess would be that this carb would still be a little
rich,
> > > but
> > >> it is just a guess. I'm not saying it won't run, it will, and it will
> > >> probably be pretty damn close to right.
> > >>
> > >> The metering rod system that Carter/Edelbrock uses will "adjust" the
> > > mixture
> > >> based on engine vacuum. The rods are controlled by a piston and
spring,
> > >> similar to many other carbs. When the engine vacuum is low, the
> metering
> > > rod
> > >> spring will start to overtake the vacuum pulling the piston down. The
> > >> rods
> > >> are tapered, and when they move up in the bore they are in, a smaller
> > >> diameter of the rod will still be inside the main jet, effectively
> > >> increasing the total main jet area that fuel can pass thru. If the
> engine
> > >> runs too rich at high vacuum conditions, but is ok at low vacuum or
> wide
> > >> open throttle, then you simply change the metering rod to on the has
a
> > >> larger diameter on the part of the rod that is in the jet at high
> vacuum
> > >> conditions. It really is a simple process, and normally will only
> require
> > > 1
> > >> or 2 sets of rods to get the carb where you need it to be.
> > >>
> > >> Chris
> > >>
> > >>
> > >> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> > >> news:OeuLg.14311$r61.1621@text.news.blueyonder.co. uk...
> > >> > Any idea if the Edelbrock 600cfm 1405 Performer + Edelbrock 2131
> > > manifold
> > >> > will require a metering or jet change on a stock 360 '91 Grand
> Wagoneer
> > > ?
> > >> >
> > >> >
> > >> > Dave Milne, Scotland
> > >> > '91 Grand Wagoneer, '99 TJ
> > >> > "c" <c@me.org> wrote in message
> > >> > news:cliLg.1294$d72.56@tornado.rdc-kc.rr.com...
> > >> >> Without knowing what size carb, choke or no choke, and which
> manifold,
> > > it
> > >> > is
> > >> >> hard to tell you what the problem could be. What I can tell you is
> > >> >> that
> > >> >> Edelbrock and Holley carbs are both set up from the factory with a
> > >> >> general
> > >> >> tune. This mean the carb may or may not need to be set up properly
> for
> > >> > your
> > >> >> particular engine. In general, the Edelbrock carbs run too rich
with
> > > the
> > >> >> factory set up. Normally they will require a metering rod change,
> and
> > >> > maybe
> > >> >> a jet change as well. You also don't specify the cam specs.
> > >> >
> > >> >
> > >> >
> > >>
> > >>
> > >
> > >
> >
> >
>
>

 

Dave,

It would be a shame to install less restrictive intake components, without
similar changes to the exhaust.

Earle

"Dave Milne" <whoneeds@toknow.com> wrote in message
news:D6_Mg.16900$r61.754@text.news.blueyonder.co.u k...
> Sounds like a good purchase - will order and wait 3 weeks for it to arrive
> (!).
>
> Got it fitted at the weekend, relatively painlessly. Well, I mean that
> metaphorically actually, as I cut the hell out of my thumb as I was
putting
> on the valley pan gasket with blood going everywhere and trying to keep it
> off the RTV. So now the nastier bits of the emissions control are
> disconnected (the EGR and the air injection stuff). As it is now not
really
> an emssions controlled vehicle, I attached it to the non-timed part of the
> carb per the instructions, but that gave me 34 degrees BTDC, so plugged it
> into the timed-port and got a more sensible 10 degrees BTDC. Gas analyser
> was playing up a bit, so I'll do the tuning next weekend, but even on the
> default settings, it is pulling way more strongly than it ever did
before -
> can't be far off.
>
> Oh, Edelbrock's instructions in the 2131 manifold state that the Performer
> 1405 requires a Square bore to ------ bore adapter. Except that both carb
> and manifold are square bore already, and I hadn't ordered one. Doesn't
> seem to mention the need for it anywhere else - will drop them a line to
> check that it is a mistake on their part. Certainly seems to run fine
> without it.
>
> Dave Milne, Scotland
>
>
> "c" <c@me.org> wrote in message
> news:RjPLg.1352$d72.768@tornado.rdc-kc.rr.com...
> > Dave, you shouldn't have a problem tuning the Carter/Edelbrock carb, and
> > yes, they are basically the same carb inside. I believe the jets and
rods
> > interchange, but I'm not positive on that. I do know that the Edelbrock
> carb
> > is heavily based on the Carter design. If you understand basic carb
> > functioning, and what the rods and jets do for the mixture, it will be a
> > simple process to get it dialed in. If you ruin in to problems, I'm sure
> we
> > can get you going in the right direction. Also, there is a book
available
> > called Carter Carb Tuning. Most of it will apply to the Edelbrock as
well.
> I
> > had the book at one time, but loaned it out and never got it back. I do
> know
> > that the book is very thorough.
> >
> > Chris
> >
> >
> > "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> > news:FiGLg.14805$r61.8273@text.news.blueyonder.co. uk...
> > > Thanks. Looks like perhaps I should have ordered the calibration kit
in
> > > retrospect. Anyhow, after a 2 week wait, it has arrived so I'll fit at
> the
> > > weekend.
> > >
> > > Quite looking forward to it - my carb experience has been mainly with
> > > multiple SU's (single barrel downdraft) and the odd side draft
Weber -
> > > never done anything on a 4 barrel like Holley or Edelbrock before.
> > >
> > > Dave Milne, Scotland
> > > '91 Grand Wagoneer, '99 TJ
> > > "c" <c@me.org> wrote in message
> > > news:1lDLg.1336$d72.134@tornado.rdc-kc.rr.com...
> > >> Dave,
> > >>
> > >> When the companies that make carb give them their initial settings
from
> > > the
> > >> factory, they take all kinds of compromised in to consideration. They
> > > don't
> > >> know if the carb will be used on a large or small displacement
engine,
> or
> > > if
> > >> it will be used in hot or cold climate, high altitude, etc. They also
> > > don't
> > >> know what other mods have been done to these engines. The baseline
> > > settings
> > >> they give these carbs will allow them to run on most of the
> applications
> > >> they will see, but they almost always require tuning to get them to
be
> > >> optimal. My guess would be that this carb would still be a little
rich,
> > > but
> > >> it is just a guess. I'm not saying it won't run, it will, and it will
> > >> probably be pretty damn close to right.
> > >>
> > >> The metering rod system that Carter/Edelbrock uses will "adjust" the
> > > mixture
> > >> based on engine vacuum. The rods are controlled by a piston and
spring,
> > >> similar to many other carbs. When the engine vacuum is low, the
> metering
> > > rod
> > >> spring will start to overtake the vacuum pulling the piston down. The
> > >> rods
> > >> are tapered, and when they move up in the bore they are in, a smaller
> > >> diameter of the rod will still be inside the main jet, effectively
> > >> increasing the total main jet area that fuel can pass thru. If the
> engine
> > >> runs too rich at high vacuum conditions, but is ok at low vacuum or
> wide
> > >> open throttle, then you simply change the metering rod to on the has
a
> > >> larger diameter on the part of the rod that is in the jet at high
> vacuum
> > >> conditions. It really is a simple process, and normally will only
> require
> > > 1
> > >> or 2 sets of rods to get the carb where you need it to be.
> > >>
> > >> Chris
> > >>
> > >>
> > >> "Dave Milne" <jeep@_nospam_milne.info> wrote in message
> > >> news:OeuLg.14311$r61.1621@text.news.blueyonder.co. uk...
> > >> > Any idea if the Edelbrock 600cfm 1405 Performer + Edelbrock 2131
> > > manifold
> > >> > will require a metering or jet change on a stock 360 '91 Grand
> Wagoneer
> > > ?
> > >> >
> > >> >
> > >> > Dave Milne, Scotland
> > >> > '91 Grand Wagoneer, '99 TJ
> > >> > "c" <c@me.org> wrote in message
> > >> > news:cliLg.1294$d72.56@tornado.rdc-kc.rr.com...
> > >> >> Without knowing what size carb, choke or no choke, and which
> manifold,
> > > it
> > >> > is
> > >> >> hard to tell you what the problem could be. What I can tell you is
> > >> >> that
> > >> >> Edelbrock and Holley carbs are both set up from the factory with a
> > >> >> general
> > >> >> tune. This mean the carb may or may not need to be set up properly
> for
> > >> > your
> > >> >> particular engine. In general, the Edelbrock carbs run too rich
with
> > > the
> > >> >> factory set up. Normally they will require a metering rod change,
> and
> > >> > maybe
> > >> >> a jet change as well. You also don't specify the cam specs.
> > >> >
> > >> >
> > >> >
> > >>
> > >>
> > >
> > >
> >
> >
>
>