Jeep TJ Forum Third generation of the classic Jeep - manufactured since 1997. Known by the coil springs and round headlights. Includes the Rubicon and Unlimited editions as well

Another Vibration Question?

Thread Tools
 
Search this Thread
 
Old 05-30-2009, 12:31 AM
  #1  
Junior Member
Thread Starter
 
GunmetalTJ's Avatar
 
Join Date: May 2009
Location: Nova Scotia
Posts: 1
Default Another Vibration Question?

First off I have to say this is a great forum with lots of great information. I did a search and founds lots on vibrations in TJ's but none like the vibration I have in mine, I have a 98 TJ sport that is stock, automatic, 4.0, no lift and stock tires it has 83,000 KM. I first noticed the vibration when pulling away from the stop sign and is around the 1500 RPM range, only under acceleration not when coasting, the vibration is noticable in the fact the mirrors vibrate and you can feel it in the seats and dash, here is where it is different from other vibration questions, if I put it in drive and hold my foot on the break and hit the 1500 rpm range it will vibrate, with no forward motion, and if I put it in park or netural and rev the engine there is no vibration. What do you think is causing this vibration? Also what RPM should my TJ idle at? and how can I set my idle speed lower? I am always haveing to ride the break going across parking lots, I can reach speeds of 15 mph without touching the gas peddle.

Thanks in advance, Danny.
GunmetalTJ is offline  
Old 06-08-2009, 12:20 PM
  #2  
Member
 
jeeplover's Avatar
 
Join Date: Jun 2009
Location: canada
Posts: 41
Default Re: Another Vibration Question?

A bad flywheel(unbalanced) might do something like that. Is the vibrations just specifically to RPM ranges? If so I would say flywheel or crankshaft.
jeeplover is offline  
Old 06-09-2009, 08:54 PM
  #3  
Junior Member
 
p8ntball's Avatar
 
Join Date: Apr 2009
Location: Kitchener
Posts: 8
Default Re: Another Vibration Question?

i have a 97 tj with the 2.4 4 cylinder and manual tranny and i get the same thing when in gear and above say 1500rpm approx, i get a bad vibration, i also get a ticking noise which i believe i have narrowed down to the heat plate above exaust (haven't had time ti fix yet) the vibration stops though once i get to coasting speed or 2500rpm approx, again this only happens when moving, even if i put clutch down and rev engine while moving i hear, but not when parked. any help would be appreciated
p8ntball is offline  
Old 06-22-2009, 09:46 AM
  #4  
Junior Member
 
knockout's Avatar
 
Join Date: Feb 2009
Location: Ottawa
Posts: 1
Default Re: Another Vibration Question?

Check the U Joints
I had the same problem and it turned out the U Joint went. The needle bearings were powder.

good luck
:)
knockout is offline  
Old 06-25-2009, 11:42 AM
  #5  
Member
 
Henry's Avatar
 
Join Date: Mar 2008
Location: Straffordville
Posts: 47
Default Re: Another Vibration Question?

If it only happens under load without moveing it has to be in the motor, try a good injecter cleaner and a tune up (plugs wires cap rotter) maybe even a new coil. Let us know what you endup doing.
Henry is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Danny Bains
Jeep Mailing List
21
02-29-2004 12:11 PM
JimG
Jeep Mailing List
15
11-27-2003 11:47 AM
Jeep Mailing List
57
11-27-2003 11:16 AM
Bob Bobby
Jeep Mailing List
0
10-07-2003 02:07 PM
Snow
Jeep Mailing List
1
08-11-2003 10:21 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 


Quick Reply: Another Vibration Question?



All times are GMT -4. The time now is 11:17 AM.

Page generated in 0.09440 seconds with 14 queries