Re: XJ transfer case linkage question
 

YES!
That's exactly the doo dad!

Thanks Will!

paul

"Will Honea" <whonea@yahoo.com> wrote in message
news:475c71c0$0$26030$88260bb3@free.teranews.com.. .
>
> Unless I'm reading you description wrong, you are referring to an exposed
> pivot shaft that fits into a bracket that just hangs off the tranny/tc.
> If
> I'm right, the slotted end of the shaft fits into a nylon bushing that is
> popped into the bracket. Damned if I know where to find one, but it
> should
> be available for a few cents (or a couple of bucks at the stealership).
> The bushing snaps into the bracket then the shaft pops into the bushing.
> Takes a fair amount of force for either part, so lube them well before you
> start.
>
> --
> Will Honea
>
> --
> Posted via a free Usenet account from http://www.teranews.com
>

Re: XJ transfer case linkage question
 

replace the bushing and snap in the linkage rod there is no clip that holds it
in

Roy wrote:

> "Earle Horton" <123456@nospam.com> wrote in message
> news:475c17fe$0$26049$88260bb3@free.teranews.com.. .
> > "paul" <SPAMpdrapeau@wi.rr.com> wrote in message
> > news:475c1dad$0$27902$4c368faf@roadrunner.com...
> >> The shaft that runs through the trunion on the transfer case linkage
> > of my
> >> wife's 95 XJ (I6 - auto) has 'slipped' out of the pivot point that it
> >> attaches to on the transfer case side.
> >>
> >> It appears that there is a snap ring type groove on the end of it. The
> > shaft
> >> also goes through a hole that obviously had some bushing in it as the
> >> diameter is approximately twice that of the shaft. Said bushing is
> > gone.
> >>
> >> I was able to put the shaft back into the TC hole and shift back in to
> > 2 wd
> >> hi.
> >>
> >> How can I repair this?
> >> Is there a snap ring inside of the TC that holds that pivot shaft in
> > place?
> >>
>
> My first concern would be that the bushing and assorted snap ring and other
> stuff isn't bouncing around in the TC

Re: XJ transfer case linkage question
 

replace the bushing and snap in the linkage rod there is no clip that holds it
in

Roy wrote:

> "Earle Horton" <123456@nospam.com> wrote in message
> news:475c17fe$0$26049$88260bb3@free.teranews.com.. .
> > "paul" <SPAMpdrapeau@wi.rr.com> wrote in message
> > news:475c1dad$0$27902$4c368faf@roadrunner.com...
> >> The shaft that runs through the trunion on the transfer case linkage
> > of my
> >> wife's 95 XJ (I6 - auto) has 'slipped' out of the pivot point that it
> >> attaches to on the transfer case side.
> >>
> >> It appears that there is a snap ring type groove on the end of it. The
> > shaft
> >> also goes through a hole that obviously had some bushing in it as the
> >> diameter is approximately twice that of the shaft. Said bushing is
> > gone.
> >>
> >> I was able to put the shaft back into the TC hole and shift back in to
> > 2 wd
> >> hi.
> >>
> >> How can I repair this?
> >> Is there a snap ring inside of the TC that holds that pivot shaft in
> > place?
> >>
>
> My first concern would be that the bushing and assorted snap ring and other
> stuff isn't bouncing around in the TC