WTB 3.73 ring and pinion
I need a good used ring and pinion for a dana 35c with 3.73 ratio.
The cross pin on mine came out and tore up everything. My guy had hoped to save me some $$$ by re-using the ring and pinion since it only had one minor chip on one of the pinion teeth. Well, is growls quite bad and when they listened with their electronic mic, they could here the tick tick of that tooth. So I think I the pinion bearings are shot, and I need new gears. They will use gears that I supply, but if they get them for me, they go through the local dealer. They want over $400. for gears. If someone in the boston area has re-geared a dana 35c I would like to purchase your old 3.73 gear set. I would like to get them this weekend if possible, so I can get this whole mess over with. If no replies this weekend, can someone recommend a source that can get them to me ASAP. Thanks Dan H. riderdan AT yahoo.com -- Dan |
Re: WTB 3.73 ring and pinion
It sounds as if you lost your cross pin, and then the shop put things back
together without replacing the pinion bearings. Correct me if this is not true. Why would you go back to that shop? I don't know, maybe you convinced them to do the job on the cheap. It almost never works out, unless you are as lucky as I am. Even I have a bad run now and then. Most any local auto parts store, NAPA, Autozone, Carquest, etc. should be able to get that gear set cheaper than the Jeep dealer. The 35c has a reputation as a cheap axle. If you cook one that bad you are likely to continue to have problems with it, no matter how many parts and dollars you throw at it. Cheers, Earle "dan" <notme@privacy.net> wrote in message news:47192496.1459165@news20.forteinc.com... > I need a good used ring and pinion for a dana 35c with 3.73 ratio. > > The cross pin on mine came out and tore up everything. My guy had > hoped to save me some $$$ by re-using the ring and pinion since it > only had one minor chip on one of the pinion teeth. > > Well, is growls quite bad and when they listened with their electronic > mic, they could here the tick tick of that tooth. > > So I think I the pinion bearings are shot, and I need new gears. > They will use gears that I supply, but if they get them for me, they > go through the local dealer. They want over $400. for gears. > > If someone in the boston area has re-geared a dana 35c I would like to > purchase your old 3.73 gear set. > > I would like to get them this weekend if possible, so I can get this > whole mess over with. > > If no replies this weekend, can someone recommend a source that can > get them to me ASAP. > > Thanks > Dan H. > > riderdan AT yahoo.com > > > -- > > Dan |
Re: WTB 3.73 ring and pinion
It sounds as if you lost your cross pin, and then the shop put things back
together without replacing the pinion bearings. Correct me if this is not true. Why would you go back to that shop? I don't know, maybe you convinced them to do the job on the cheap. It almost never works out, unless you are as lucky as I am. Even I have a bad run now and then. Most any local auto parts store, NAPA, Autozone, Carquest, etc. should be able to get that gear set cheaper than the Jeep dealer. The 35c has a reputation as a cheap axle. If you cook one that bad you are likely to continue to have problems with it, no matter how many parts and dollars you throw at it. Cheers, Earle "dan" <notme@privacy.net> wrote in message news:47192496.1459165@news20.forteinc.com... > I need a good used ring and pinion for a dana 35c with 3.73 ratio. > > The cross pin on mine came out and tore up everything. My guy had > hoped to save me some $$$ by re-using the ring and pinion since it > only had one minor chip on one of the pinion teeth. > > Well, is growls quite bad and when they listened with their electronic > mic, they could here the tick tick of that tooth. > > So I think I the pinion bearings are shot, and I need new gears. > They will use gears that I supply, but if they get them for me, they > go through the local dealer. They want over $400. for gears. > > If someone in the boston area has re-geared a dana 35c I would like to > purchase your old 3.73 gear set. > > I would like to get them this weekend if possible, so I can get this > whole mess over with. > > If no replies this weekend, can someone recommend a source that can > get them to me ASAP. > > Thanks > Dan H. > > riderdan AT yahoo.com > > > -- > > Dan |
Re: WTB 3.73 ring and pinion
It sounds as if you lost your cross pin, and then the shop put things back
together without replacing the pinion bearings. Correct me if this is not true. Why would you go back to that shop? I don't know, maybe you convinced them to do the job on the cheap. It almost never works out, unless you are as lucky as I am. Even I have a bad run now and then. Most any local auto parts store, NAPA, Autozone, Carquest, etc. should be able to get that gear set cheaper than the Jeep dealer. The 35c has a reputation as a cheap axle. If you cook one that bad you are likely to continue to have problems with it, no matter how many parts and dollars you throw at it. Cheers, Earle "dan" <notme@privacy.net> wrote in message news:47192496.1459165@news20.forteinc.com... > I need a good used ring and pinion for a dana 35c with 3.73 ratio. > > The cross pin on mine came out and tore up everything. My guy had > hoped to save me some $$$ by re-using the ring and pinion since it > only had one minor chip on one of the pinion teeth. > > Well, is growls quite bad and when they listened with their electronic > mic, they could here the tick tick of that tooth. > > So I think I the pinion bearings are shot, and I need new gears. > They will use gears that I supply, but if they get them for me, they > go through the local dealer. They want over $400. for gears. > > If someone in the boston area has re-geared a dana 35c I would like to > purchase your old 3.73 gear set. > > I would like to get them this weekend if possible, so I can get this > whole mess over with. > > If no replies this weekend, can someone recommend a source that can > get them to me ASAP. > > Thanks > Dan H. > > riderdan AT yahoo.com > > > -- > > Dan |
Re: WTB 3.73 ring and pinion
dan wrote:
> I need a good used ring and pinion for a dana 35c with 3.73 ratio. > > The cross pin on mine came out and tore up everything. My guy had > hoped to save me some $$$ by re-using the ring and pinion since it > only had one minor chip on one of the pinion teeth. > > Well, is growls quite bad and when they listened with their electronic > mic, they could here the tick tick of that tooth. > > So I think I the pinion bearings are shot, and I need new gears. > They will use gears that I supply, but if they get them for me, they > go through the local dealer. They want over $400. for gears. > > If someone in the boston area has re-geared a dana 35c I would like to > purchase your old 3.73 gear set. > > I would like to get them this weekend if possible, so I can get this > whole mess over with. > > If no replies this weekend, can someone recommend a source that can > get them to me ASAP. > > Thanks > Dan H. > > riderdan AT yahoo.com > > http://www.ringpinion.com/ProductDet...px?ProdID=4436 http://reiderracing.com/dana35.htm good luck Chris |
Re: WTB 3.73 ring and pinion
dan wrote:
> I need a good used ring and pinion for a dana 35c with 3.73 ratio. > > The cross pin on mine came out and tore up everything. My guy had > hoped to save me some $$$ by re-using the ring and pinion since it > only had one minor chip on one of the pinion teeth. > > Well, is growls quite bad and when they listened with their electronic > mic, they could here the tick tick of that tooth. > > So I think I the pinion bearings are shot, and I need new gears. > They will use gears that I supply, but if they get them for me, they > go through the local dealer. They want over $400. for gears. > > If someone in the boston area has re-geared a dana 35c I would like to > purchase your old 3.73 gear set. > > I would like to get them this weekend if possible, so I can get this > whole mess over with. > > If no replies this weekend, can someone recommend a source that can > get them to me ASAP. > > Thanks > Dan H. > > riderdan AT yahoo.com > > http://www.ringpinion.com/ProductDet...px?ProdID=4436 http://reiderracing.com/dana35.htm good luck Chris |
Re: WTB 3.73 ring and pinion
dan wrote:
> I need a good used ring and pinion for a dana 35c with 3.73 ratio. > > The cross pin on mine came out and tore up everything. My guy had > hoped to save me some $$$ by re-using the ring and pinion since it > only had one minor chip on one of the pinion teeth. > > Well, is growls quite bad and when they listened with their electronic > mic, they could here the tick tick of that tooth. > > So I think I the pinion bearings are shot, and I need new gears. > They will use gears that I supply, but if they get them for me, they > go through the local dealer. They want over $400. for gears. > > If someone in the boston area has re-geared a dana 35c I would like to > purchase your old 3.73 gear set. > > I would like to get them this weekend if possible, so I can get this > whole mess over with. > > If no replies this weekend, can someone recommend a source that can > get them to me ASAP. > > Thanks > Dan H. > > riderdan AT yahoo.com > > http://www.ringpinion.com/ProductDet...px?ProdID=4436 http://reiderracing.com/dana35.htm good luck Chris |
Re: WTB 3.73 ring and pinion
What's that Lassie? You say that Earle Horton fell down the old
rec.autos.makers.jeep+willys mine and will die if we don't mount a rescue by Fri, 19 Oct 2007 16:51:31 -0600: >It sounds as if you lost your cross pin, and then the shop put things back >together without replacing the pinion bearings. Correct me if this is not >true. Why would you go back to that shop? I don't know, maybe you >convinced them to do the job on the cheap. It almost never works out, >unless you are as lucky as I am. Even I have a bad run now and then. Yes, that's it. Killed the tranny too. I'm lucky I could drive it home. I lost 3rd and 4th gear, had to limp home with just 1,2, 5 and reverse. They thought that we could get away with it, so I said OK. Turns out I was wrong. But anyway, they will not charge me for the labor, just the parts. > >Most any local auto parts store, NAPA, Autozone, Carquest, etc. should be >able to get that gear set cheaper than the Jeep dealer. But can they get it by Monday? I will ask around on saturday, but if someone in the area has swapped to different gears and doesn't need their old ones, I could use them. > >The 35c has a reputation as a cheap axle. If you cook one that bad you are >likely to continue to have problems with it, no matter how many parts and >dollars you throw at it. I know, too late now. If I had it to do over again, I would get a whole new axle assembly. > >Cheers, > >Earle > >"dan" <notme@privacy.net> wrote in message >news:47192496.1459165@news20.forteinc.com... >> I need a good used ring and pinion for a dana 35c with 3.73 ratio. >> >> The cross pin on mine came out and tore up everything. My guy had >> hoped to save me some $$$ by re-using the ring and pinion since it >> only had one minor chip on one of the pinion teeth. >> >> Well, is growls quite bad and when they listened with their electronic >> mic, they could here the tick tick of that tooth. >> >> So I think I the pinion bearings are shot, and I need new gears. >> They will use gears that I supply, but if they get them for me, they >> go through the local dealer. They want over $400. for gears. >> >> If someone in the boston area has re-geared a dana 35c I would like to >> purchase your old 3.73 gear set. >> >> I would like to get them this weekend if possible, so I can get this >> whole mess over with. >> >> If no replies this weekend, can someone recommend a source that can >> get them to me ASAP. >> >> Thanks >> Dan H. >> >> riderdan AT yahoo.com >> >> >> -- >> >> Dan > -- Dan |
Re: WTB 3.73 ring and pinion
What's that Lassie? You say that Earle Horton fell down the old
rec.autos.makers.jeep+willys mine and will die if we don't mount a rescue by Fri, 19 Oct 2007 16:51:31 -0600: >It sounds as if you lost your cross pin, and then the shop put things back >together without replacing the pinion bearings. Correct me if this is not >true. Why would you go back to that shop? I don't know, maybe you >convinced them to do the job on the cheap. It almost never works out, >unless you are as lucky as I am. Even I have a bad run now and then. Yes, that's it. Killed the tranny too. I'm lucky I could drive it home. I lost 3rd and 4th gear, had to limp home with just 1,2, 5 and reverse. They thought that we could get away with it, so I said OK. Turns out I was wrong. But anyway, they will not charge me for the labor, just the parts. > >Most any local auto parts store, NAPA, Autozone, Carquest, etc. should be >able to get that gear set cheaper than the Jeep dealer. But can they get it by Monday? I will ask around on saturday, but if someone in the area has swapped to different gears and doesn't need their old ones, I could use them. > >The 35c has a reputation as a cheap axle. If you cook one that bad you are >likely to continue to have problems with it, no matter how many parts and >dollars you throw at it. I know, too late now. If I had it to do over again, I would get a whole new axle assembly. > >Cheers, > >Earle > >"dan" <notme@privacy.net> wrote in message >news:47192496.1459165@news20.forteinc.com... >> I need a good used ring and pinion for a dana 35c with 3.73 ratio. >> >> The cross pin on mine came out and tore up everything. My guy had >> hoped to save me some $$$ by re-using the ring and pinion since it >> only had one minor chip on one of the pinion teeth. >> >> Well, is growls quite bad and when they listened with their electronic >> mic, they could here the tick tick of that tooth. >> >> So I think I the pinion bearings are shot, and I need new gears. >> They will use gears that I supply, but if they get them for me, they >> go through the local dealer. They want over $400. for gears. >> >> If someone in the boston area has re-geared a dana 35c I would like to >> purchase your old 3.73 gear set. >> >> I would like to get them this weekend if possible, so I can get this >> whole mess over with. >> >> If no replies this weekend, can someone recommend a source that can >> get them to me ASAP. >> >> Thanks >> Dan H. >> >> riderdan AT yahoo.com >> >> >> -- >> >> Dan > -- Dan |
Re: WTB 3.73 ring and pinion
What's that Lassie? You say that Earle Horton fell down the old
rec.autos.makers.jeep+willys mine and will die if we don't mount a rescue by Fri, 19 Oct 2007 16:51:31 -0600: >It sounds as if you lost your cross pin, and then the shop put things back >together without replacing the pinion bearings. Correct me if this is not >true. Why would you go back to that shop? I don't know, maybe you >convinced them to do the job on the cheap. It almost never works out, >unless you are as lucky as I am. Even I have a bad run now and then. Yes, that's it. Killed the tranny too. I'm lucky I could drive it home. I lost 3rd and 4th gear, had to limp home with just 1,2, 5 and reverse. They thought that we could get away with it, so I said OK. Turns out I was wrong. But anyway, they will not charge me for the labor, just the parts. > >Most any local auto parts store, NAPA, Autozone, Carquest, etc. should be >able to get that gear set cheaper than the Jeep dealer. But can they get it by Monday? I will ask around on saturday, but if someone in the area has swapped to different gears and doesn't need their old ones, I could use them. > >The 35c has a reputation as a cheap axle. If you cook one that bad you are >likely to continue to have problems with it, no matter how many parts and >dollars you throw at it. I know, too late now. If I had it to do over again, I would get a whole new axle assembly. > >Cheers, > >Earle > >"dan" <notme@privacy.net> wrote in message >news:47192496.1459165@news20.forteinc.com... >> I need a good used ring and pinion for a dana 35c with 3.73 ratio. >> >> The cross pin on mine came out and tore up everything. My guy had >> hoped to save me some $$$ by re-using the ring and pinion since it >> only had one minor chip on one of the pinion teeth. >> >> Well, is growls quite bad and when they listened with their electronic >> mic, they could here the tick tick of that tooth. >> >> So I think I the pinion bearings are shot, and I need new gears. >> They will use gears that I supply, but if they get them for me, they >> go through the local dealer. They want over $400. for gears. >> >> If someone in the boston area has re-geared a dana 35c I would like to >> purchase your old 3.73 gear set. >> >> I would like to get them this weekend if possible, so I can get this >> whole mess over with. >> >> If no replies this weekend, can someone recommend a source that can >> get them to me ASAP. >> >> Thanks >> Dan H. >> >> riderdan AT yahoo.com >> >> >> -- >> >> Dan > -- Dan |
All times are GMT -4. The time now is 07:40 AM. |
© 2024 MH Sub I, LLC dba Internet Brands