woo hoo!
#11
Guest
Posts: n/a
Re: woo hoo!
Mike Romain wrote:
> Just fyi, when you have a castle nut to the proper torque and the hole
> doesn't line up, it is proper practice to tighten it more until the
> pin will slide through.
Yep.. initially set it then gave it a bit more to find the hole.
Then gave it a bit more to get to the next hole but that was starting
to go too far over the torque spec. The part is correct and the
hole/shaft clean so it couldn't be dirt.
> Taking a piece out of the castle weakens it. If it doesn't go onto
> the bolt far enough to set the pin, you have something wrong, either
> dirt or a deformed part or the wrong part.
Took another look at it and measured against the old one. The castle
nuts are the same but the old part has a chamfer around the hole and
the hole is just a teeny <1mm bit closer to the end. The only filing
I did was to ease the edges on the hole just a bit so the pin would
slide in. And on that note, the pin was also a bit bigger than the
old one.
I think it's one of those "close but not exact" parts.
The shoulder is set so there is no more that can be sucked in.
--
DougW
> Just fyi, when you have a castle nut to the proper torque and the hole
> doesn't line up, it is proper practice to tighten it more until the
> pin will slide through.
Yep.. initially set it then gave it a bit more to find the hole.
Then gave it a bit more to get to the next hole but that was starting
to go too far over the torque spec. The part is correct and the
hole/shaft clean so it couldn't be dirt.
> Taking a piece out of the castle weakens it. If it doesn't go onto
> the bolt far enough to set the pin, you have something wrong, either
> dirt or a deformed part or the wrong part.
Took another look at it and measured against the old one. The castle
nuts are the same but the old part has a chamfer around the hole and
the hole is just a teeny <1mm bit closer to the end. The only filing
I did was to ease the edges on the hole just a bit so the pin would
slide in. And on that note, the pin was also a bit bigger than the
old one.
I think it's one of those "close but not exact" parts.
The shoulder is set so there is no more that can be sucked in.
--
DougW
#12
Guest
Posts: n/a
Re: woo hoo!
Mike Romain wrote:
> Just fyi, when you have a castle nut to the proper torque and the hole
> doesn't line up, it is proper practice to tighten it more until the
> pin will slide through.
Yep.. initially set it then gave it a bit more to find the hole.
Then gave it a bit more to get to the next hole but that was starting
to go too far over the torque spec. The part is correct and the
hole/shaft clean so it couldn't be dirt.
> Taking a piece out of the castle weakens it. If it doesn't go onto
> the bolt far enough to set the pin, you have something wrong, either
> dirt or a deformed part or the wrong part.
Took another look at it and measured against the old one. The castle
nuts are the same but the old part has a chamfer around the hole and
the hole is just a teeny <1mm bit closer to the end. The only filing
I did was to ease the edges on the hole just a bit so the pin would
slide in. And on that note, the pin was also a bit bigger than the
old one.
I think it's one of those "close but not exact" parts.
The shoulder is set so there is no more that can be sucked in.
--
DougW
> Just fyi, when you have a castle nut to the proper torque and the hole
> doesn't line up, it is proper practice to tighten it more until the
> pin will slide through.
Yep.. initially set it then gave it a bit more to find the hole.
Then gave it a bit more to get to the next hole but that was starting
to go too far over the torque spec. The part is correct and the
hole/shaft clean so it couldn't be dirt.
> Taking a piece out of the castle weakens it. If it doesn't go onto
> the bolt far enough to set the pin, you have something wrong, either
> dirt or a deformed part or the wrong part.
Took another look at it and measured against the old one. The castle
nuts are the same but the old part has a chamfer around the hole and
the hole is just a teeny <1mm bit closer to the end. The only filing
I did was to ease the edges on the hole just a bit so the pin would
slide in. And on that note, the pin was also a bit bigger than the
old one.
I think it's one of those "close but not exact" parts.
The shoulder is set so there is no more that can be sucked in.
--
DougW
#13
Guest
Posts: n/a
Re: woo hoo!
Mike Romain wrote:
> Just fyi, when you have a castle nut to the proper torque and the hole
> doesn't line up, it is proper practice to tighten it more until the
> pin will slide through.
Yep.. initially set it then gave it a bit more to find the hole.
Then gave it a bit more to get to the next hole but that was starting
to go too far over the torque spec. The part is correct and the
hole/shaft clean so it couldn't be dirt.
> Taking a piece out of the castle weakens it. If it doesn't go onto
> the bolt far enough to set the pin, you have something wrong, either
> dirt or a deformed part or the wrong part.
Took another look at it and measured against the old one. The castle
nuts are the same but the old part has a chamfer around the hole and
the hole is just a teeny <1mm bit closer to the end. The only filing
I did was to ease the edges on the hole just a bit so the pin would
slide in. And on that note, the pin was also a bit bigger than the
old one.
I think it's one of those "close but not exact" parts.
The shoulder is set so there is no more that can be sucked in.
--
DougW
> Just fyi, when you have a castle nut to the proper torque and the hole
> doesn't line up, it is proper practice to tighten it more until the
> pin will slide through.
Yep.. initially set it then gave it a bit more to find the hole.
Then gave it a bit more to get to the next hole but that was starting
to go too far over the torque spec. The part is correct and the
hole/shaft clean so it couldn't be dirt.
> Taking a piece out of the castle weakens it. If it doesn't go onto
> the bolt far enough to set the pin, you have something wrong, either
> dirt or a deformed part or the wrong part.
Took another look at it and measured against the old one. The castle
nuts are the same but the old part has a chamfer around the hole and
the hole is just a teeny <1mm bit closer to the end. The only filing
I did was to ease the edges on the hole just a bit so the pin would
slide in. And on that note, the pin was also a bit bigger than the
old one.
I think it's one of those "close but not exact" parts.
The shoulder is set so there is no more that can be sucked in.
--
DougW
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)