Wiper Motor Assembly Question
10-10-2004, 12:01 PM
#1
Guest
Posts: n/a
Wiper Motor Assembly Question
OK, I have a question that I need answered as fast as possible as I'm
probably heading to the scrap yards in an hour or two to find one:
What year Jeeps/Cherokees/Commanches/etcetcetc wiper motor assemblies will
fit in a 1985 Jeep CJ7?
More specifically, I'll describe my problem:
The wiper motor itself actually works fine. There's the set of 4 wires that
run into this little metal assembly with a plastic gear inside. This gear
will no longer turn because the metal rod that is supposed to turn it (comes
out through the other side of this metal assembly) is seized. I've tried all
kinds of anti-corrosives and penetrating oils and it won't even remotely
budge. I have no idea how it seized so bad in a matter of a week or so of
not being used, so if anyone wants to hazard a guess as to: a) how to fix it
and; b) how to prevent this from happening again, it would be greatly
appreciated!!
Thanks!
probably heading to the scrap yards in an hour or two to find one:
What year Jeeps/Cherokees/Commanches/etcetcetc wiper motor assemblies will
fit in a 1985 Jeep CJ7?
More specifically, I'll describe my problem:
The wiper motor itself actually works fine. There's the set of 4 wires that
run into this little metal assembly with a plastic gear inside. This gear
will no longer turn because the metal rod that is supposed to turn it (comes
out through the other side of this metal assembly) is seized. I've tried all
kinds of anti-corrosives and penetrating oils and it won't even remotely
budge. I have no idea how it seized so bad in a matter of a week or so of
not being used, so if anyone wants to hazard a guess as to: a) how to fix it
and; b) how to prevent this from happening again, it would be greatly
appreciated!!
Thanks!
10-10-2004, 01:56 PM
#2
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
20 minutes and the pin knocked loose. Now if I can remember how to assemble
it all, I'm good to go (hopefully).
When in doubt, smash with a hammer. When the doubt increases, so does the
weight of the hammer.
Smashy Smashy
Now on a completely unrelated note ...wth am I supposed to mount tow hooks
on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
hoop bumper on the front (now I realize this was a mistake) and just the
flat panel on the rear for now. I'm going to get a custom rear made with
4.75 ton shackle's built in, but for now I'm not sure where to stick them.
Argh.
20 minutes and the pin knocked loose. Now if I can remember how to assemble
it all, I'm good to go (hopefully).
When in doubt, smash with a hammer. When the doubt increases, so does the
weight of the hammer.
Smashy Smashy
Now on a completely unrelated note ...wth am I supposed to mount tow hooks
on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
hoop bumper on the front (now I realize this was a mistake) and just the
flat panel on the rear for now. I'm going to get a custom rear made with
4.75 ton shackle's built in, but for now I'm not sure where to stick them.
Argh.
10-10-2004, 01:56 PM
#3
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
20 minutes and the pin knocked loose. Now if I can remember how to assemble
it all, I'm good to go (hopefully).
When in doubt, smash with a hammer. When the doubt increases, so does the
weight of the hammer.
Smashy Smashy
Now on a completely unrelated note ...wth am I supposed to mount tow hooks
on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
hoop bumper on the front (now I realize this was a mistake) and just the
flat panel on the rear for now. I'm going to get a custom rear made with
4.75 ton shackle's built in, but for now I'm not sure where to stick them.
Argh.
20 minutes and the pin knocked loose. Now if I can remember how to assemble
it all, I'm good to go (hopefully).
When in doubt, smash with a hammer. When the doubt increases, so does the
weight of the hammer.
Smashy Smashy
Now on a completely unrelated note ...wth am I supposed to mount tow hooks
on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
hoop bumper on the front (now I realize this was a mistake) and just the
flat panel on the rear for now. I'm going to get a custom rear made with
4.75 ton shackle's built in, but for now I'm not sure where to stick them.
Argh.
10-10-2004, 01:56 PM
#4
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
20 minutes and the pin knocked loose. Now if I can remember how to assemble
it all, I'm good to go (hopefully).
When in doubt, smash with a hammer. When the doubt increases, so does the
weight of the hammer.
Smashy Smashy
Now on a completely unrelated note ...wth am I supposed to mount tow hooks
on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
hoop bumper on the front (now I realize this was a mistake) and just the
flat panel on the rear for now. I'm going to get a custom rear made with
4.75 ton shackle's built in, but for now I'm not sure where to stick them.
Argh.
20 minutes and the pin knocked loose. Now if I can remember how to assemble
it all, I'm good to go (hopefully).
When in doubt, smash with a hammer. When the doubt increases, so does the
weight of the hammer.
Smashy Smashy
Now on a completely unrelated note ...wth am I supposed to mount tow hooks
on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
hoop bumper on the front (now I realize this was a mistake) and just the
flat panel on the rear for now. I'm going to get a custom rear made with
4.75 ton shackle's built in, but for now I'm not sure where to stick them.
Argh.
10-10-2004, 03:54 PM
#5
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
griffin did pass the time by typing:
> NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
> 20 minutes and the pin knocked loose. Now if I can remember how to assemble
> it all, I'm good to go (hopefully).
>
> When in doubt, smash with a hammer. When the doubt increases, so does the
> weight of the hammer.
>
> Smashy Smashy
It's a fine art, that. :)
Too rainy outside or I'd put up a link to my fix-it tool.
(30lb sledge used for persuading railroad track.)
> Now on a completely unrelated note ...wth am I supposed to mount tow hooks
> on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
> hoop bumper on the front (now I realize this was a mistake) and just the
> flat panel on the rear for now. I'm going to get a custom rear made with
> 4.75 ton shackle's built in, but for now I'm not sure where to stick them.
> Argh.
Dunno.
This link might help.
http://www.4x4xplor.com/cj.html
If the rain keep up around here (Oklahoma) I'm gonna need
bigger tires. :]
--
DougW
> NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
> 20 minutes and the pin knocked loose. Now if I can remember how to assemble
> it all, I'm good to go (hopefully).
>
> When in doubt, smash with a hammer. When the doubt increases, so does the
> weight of the hammer.
>
> Smashy Smashy
It's a fine art, that. :)
Too rainy outside or I'd put up a link to my fix-it tool.
(30lb sledge used for persuading railroad track.)
> Now on a completely unrelated note ...wth am I supposed to mount tow hooks
> on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
> hoop bumper on the front (now I realize this was a mistake) and just the
> flat panel on the rear for now. I'm going to get a custom rear made with
> 4.75 ton shackle's built in, but for now I'm not sure where to stick them.
> Argh.
Dunno.
This link might help.
http://www.4x4xplor.com/cj.html
If the rain keep up around here (Oklahoma) I'm gonna need
bigger tires. :]
--
DougW
10-10-2004, 03:54 PM
#6
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
griffin did pass the time by typing:
> NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
> 20 minutes and the pin knocked loose. Now if I can remember how to assemble
> it all, I'm good to go (hopefully).
>
> When in doubt, smash with a hammer. When the doubt increases, so does the
> weight of the hammer.
>
> Smashy Smashy
It's a fine art, that. :)
Too rainy outside or I'd put up a link to my fix-it tool.
(30lb sledge used for persuading railroad track.)
> Now on a completely unrelated note ...wth am I supposed to mount tow hooks
> on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
> hoop bumper on the front (now I realize this was a mistake) and just the
> flat panel on the rear for now. I'm going to get a custom rear made with
> 4.75 ton shackle's built in, but for now I'm not sure where to stick them.
> Argh.
Dunno.
This link might help.
http://www.4x4xplor.com/cj.html
If the rain keep up around here (Oklahoma) I'm gonna need
bigger tires. :]
--
DougW
> NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
> 20 minutes and the pin knocked loose. Now if I can remember how to assemble
> it all, I'm good to go (hopefully).
>
> When in doubt, smash with a hammer. When the doubt increases, so does the
> weight of the hammer.
>
> Smashy Smashy
It's a fine art, that. :)
Too rainy outside or I'd put up a link to my fix-it tool.
(30lb sledge used for persuading railroad track.)
> Now on a completely unrelated note ...wth am I supposed to mount tow hooks
> on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
> hoop bumper on the front (now I realize this was a mistake) and just the
> flat panel on the rear for now. I'm going to get a custom rear made with
> 4.75 ton shackle's built in, but for now I'm not sure where to stick them.
> Argh.
Dunno.
This link might help.
http://www.4x4xplor.com/cj.html
If the rain keep up around here (Oklahoma) I'm gonna need
bigger tires. :]
--
DougW
10-10-2004, 03:54 PM
#7
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
griffin did pass the time by typing:
> NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
> 20 minutes and the pin knocked loose. Now if I can remember how to assemble
> it all, I'm good to go (hopefully).
>
> When in doubt, smash with a hammer. When the doubt increases, so does the
> weight of the hammer.
>
> Smashy Smashy
It's a fine art, that. :)
Too rainy outside or I'd put up a link to my fix-it tool.
(30lb sledge used for persuading railroad track.)
> Now on a completely unrelated note ...wth am I supposed to mount tow hooks
> on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
> hoop bumper on the front (now I realize this was a mistake) and just the
> flat panel on the rear for now. I'm going to get a custom rear made with
> 4.75 ton shackle's built in, but for now I'm not sure where to stick them.
> Argh.
Dunno.
This link might help.
http://www.4x4xplor.com/cj.html
If the rain keep up around here (Oklahoma) I'm gonna need
bigger tires. :]
--
DougW
> NM ...I got mad and smashed the hell out of it with a 2lb hammer for about
> 20 minutes and the pin knocked loose. Now if I can remember how to assemble
> it all, I'm good to go (hopefully).
>
> When in doubt, smash with a hammer. When the doubt increases, so does the
> weight of the hammer.
>
> Smashy Smashy
It's a fine art, that. :)
Too rainy outside or I'd put up a link to my fix-it tool.
(30lb sledge used for persuading railroad track.)
> Now on a completely unrelated note ...wth am I supposed to mount tow hooks
> on a stock '85 CJ7. Anyone have any good "spots"? I'm using a double-tube
> hoop bumper on the front (now I realize this was a mistake) and just the
> flat panel on the rear for now. I'm going to get a custom rear made with
> 4.75 ton shackle's built in, but for now I'm not sure where to stick them.
> Argh.
Dunno.
This link might help.
http://www.4x4xplor.com/cj.html
If the rain keep up around here (Oklahoma) I'm gonna need
bigger tires. :]
--
DougW
10-11-2004, 04:06 AM
#8
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
Rainy? We haven't had rain in over 175 days:
http://sandiegoblog.com/archives/200...still-no-rain/ We should
have the record in six more days.
http://www.wrcc.dri.edu/cgi-bin/cliMONtpre.pl?casand
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
> Too rainy outside or I'd put up a link to my fix-it tool.
> (30lb sledge used for persuading railroad track.)
>
> Dunno.
> This link might help.
> http://www.4x4xplor.com/cj.html
>
> If the rain keep up around here (Oklahoma) I'm gonna need
> bigger tires. :]
>
> --
> DougW
http://sandiegoblog.com/archives/200...still-no-rain/ We should
have the record in six more days.
http://www.wrcc.dri.edu/cgi-bin/cliMONtpre.pl?casand
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
> Too rainy outside or I'd put up a link to my fix-it tool.
> (30lb sledge used for persuading railroad track.)
>
> Dunno.
> This link might help.
> http://www.4x4xplor.com/cj.html
>
> If the rain keep up around here (Oklahoma) I'm gonna need
> bigger tires. :]
>
> --
> DougW
10-11-2004, 04:06 AM
#9
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
Rainy? We haven't had rain in over 175 days:
http://sandiegoblog.com/archives/200...still-no-rain/ We should
have the record in six more days.
http://www.wrcc.dri.edu/cgi-bin/cliMONtpre.pl?casand
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
> Too rainy outside or I'd put up a link to my fix-it tool.
> (30lb sledge used for persuading railroad track.)
>
> Dunno.
> This link might help.
> http://www.4x4xplor.com/cj.html
>
> If the rain keep up around here (Oklahoma) I'm gonna need
> bigger tires. :]
>
> --
> DougW
http://sandiegoblog.com/archives/200...still-no-rain/ We should
have the record in six more days.
http://www.wrcc.dri.edu/cgi-bin/cliMONtpre.pl?casand
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
> Too rainy outside or I'd put up a link to my fix-it tool.
> (30lb sledge used for persuading railroad track.)
>
> Dunno.
> This link might help.
> http://www.4x4xplor.com/cj.html
>
> If the rain keep up around here (Oklahoma) I'm gonna need
> bigger tires. :]
>
> --
> DougW
10-11-2004, 04:06 AM
#10
Guest
Posts: n/a
Re: Wiper Motor Assembly Question
Rainy? We haven't had rain in over 175 days:
http://sandiegoblog.com/archives/200...still-no-rain/ We should
have the record in six more days.
http://www.wrcc.dri.edu/cgi-bin/cliMONtpre.pl?casand
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
> Too rainy outside or I'd put up a link to my fix-it tool.
> (30lb sledge used for persuading railroad track.)
>
> Dunno.
> This link might help.
> http://www.4x4xplor.com/cj.html
>
> If the rain keep up around here (Oklahoma) I'm gonna need
> bigger tires. :]
>
> --
> DougW
http://sandiegoblog.com/archives/200...still-no-rain/ We should
have the record in six more days.
http://www.wrcc.dri.edu/cgi-bin/cliMONtpre.pl?casand
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
> Too rainy outside or I'd put up a link to my fix-it tool.
> (30lb sledge used for persuading railroad track.)
>
> Dunno.
> This link might help.
> http://www.4x4xplor.com/cj.html
>
> If the rain keep up around here (Oklahoma) I'm gonna need
> bigger tires. :]
>
> --
> DougW