Where to get tranny line clip?
02-12-2007, 10:31 AM
#21
Guest
Posts: n/a
Re: Where to get tranny line clip?
Since apparently your local dealership is going to be NO help, you
might try a reputable transmission shop since they routinely
disconnect these during repairs.
Personally, I would remove the line and look for that O-Ring mentioned
above. It should have one "somewhere", either on the end of the line
itself or captive in the fitting that it plugs into. Either way, you
should replace it with one from a hydraulics shop. There are gobs of
cheap junk O-Rings out there that will fall apart when exposed to oil.
Inspect the original "clip" and if it is not broken re-use it. If it
is broken, I would try that clip you mentioned earlier. The clip
only retains the line, it does not do the sealing.
Good Luck!
Bruce
02-12-2007, 10:40 AM
#22
Guest
Posts: n/a
Re: Where to get tranny line clip?
ajcrm125 wrote:
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-12-2007, 10:40 AM
#23
Guest
Posts: n/a
Re: Where to get tranny line clip?
ajcrm125 wrote:
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-12-2007, 10:40 AM
#24
Guest
Posts: n/a
Re: Where to get tranny line clip?
ajcrm125 wrote:
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-12-2007, 10:40 AM
#25
Guest
Posts: n/a
Re: Where to get tranny line clip?
ajcrm125 wrote:
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
>> ajcrm125 wrote:
>>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
>>> joint by the cooler which leads me to believe I need a new plastic
>>> clip.
>>> The clip looks like this:
>>> http://ken-co.com/fmsi/3102.jpg
>>> Now I can find this clip in my local auto parts store but it's shown
>>> as a fuel line part. I bought one anyways to check and it seemed
>>> really flimsy... I didn't want to chance it.
>> Looks like the fuel line clip to me. Mine have a teeny metal
>> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>>
>> That clip simply holds the fitting on, what you need is
>> new O rings that are inside that fitting. Unfortunatly
>> I don't know any other source than the dealer unless Napa
>> has a replacement part. Tried calling a local hydraulic hose shop?
>>
>>> I went to the the dealer and they said they don't sell the clip
>>> separately.. I would have to buy the whole line; $90. Forget that. I
>>> can't believe that every time someone brings their vehocle in and a
>>> clip needs to get repaired thy rip out the whole line as well.
>>> Where can I get this part?
>> Trywww.chryslerpartsdirect.comand see what they have for OEM cost.
>> They are a dealership but they don't price gouge.
>>
>> I've found out that sometimes there is no good cheap solution that
>> lasts.
>>
>> --
>> DougW
>
> Hmm.... Called the local dealer and they said that the line (o-rings
> etc included) are discontinued. They do the whole thing in hard
> tubing now. Does anyone know if there are aftermarket kits out there
> to do this? I've re-done solid break lines etc... I'm assuming the
> process is similar.
> Thanks...
>
I have always replaced and repaired tranny cooler line with the 'rubber'
version. It works great and fits on with clamps. The also make 'high
pressure' worm gear clamps now or I use two regular ones side by side.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-12-2007, 11:14 AM
#26
Guest
Posts: n/a
Re: Where to get tranny line clip?
On Feb 12, 10:40 am, Mike Romain <roma...@sympatico.ca> wrote:
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
02-12-2007, 11:14 AM
#27
Guest
Posts: n/a
Re: Where to get tranny line clip?
On Feb 12, 10:40 am, Mike Romain <roma...@sympatico.ca> wrote:
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
02-12-2007, 11:14 AM
#28
Guest
Posts: n/a
Re: Where to get tranny line clip?
On Feb 12, 10:40 am, Mike Romain <roma...@sympatico.ca> wrote:
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
02-12-2007, 11:14 AM
#29
Guest
Posts: n/a
Re: Where to get tranny line clip?
On Feb 12, 10:40 am, Mike Romain <roma...@sympatico.ca> wrote:
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
> ajcrm125 wrote:
> > On Feb 11, 9:27 pm, "DougW" <post.repl...@invalid.address> wrote:
> >> ajcrm125 wrote:
> >>> I have a 85 Jeep Grand Cherokee. My tranny line is leaking at the
> >>> joint by the cooler which leads me to believe I need a new plastic
> >>> clip.
> >>> The clip looks like this:
> >>>http://ken-co.com/fmsi/3102.jpg
> >>> Now I can find this clip in my local auto parts store but it's shown
> >>> as a fuel line part. I bought one anyways to check and it seemed
> >>> really flimsy... I didn't want to chance it.
> >> Looks like the fuel line clip to me. Mine have a teeny metal
> >> spring clip and a plastic carrier.http://www.revbeergoggles.com/temp/trans-connector.jpg
>
> >> That clip simply holds the fitting on, what you need is
> >> new O rings that are inside that fitting. Unfortunatly
> >> I don't know any other source than the dealer unless Napa
> >> has a replacement part. Tried calling a local hydraulic hose shop?
>
> >>> I went to the the dealer and they said they don't sell the clip
> >>> separately.. I would have to buy the whole line; $90. Forget that. I
> >>> can't believe that every time someone brings their vehocle in and a
> >>> clip needs to get repaired thy rip out the whole line as well.
> >>> Where can I get this part?
> >> Trywww.chryslerpartsdirect.comandsee what they have for OEM cost.
> >> They are a dealership but they don't price gouge.
>
> >> I've found out that sometimes there is no good cheap solution that
> >> lasts.
>
> >> --
> >> DougW
>
> > Hmm.... Called the local dealer and they said that the line (o-rings
> > etc included) are discontinued. They do the whole thing in hard
> > tubing now. Does anyone know if there are aftermarket kits out there
> > to do this? I've re-done solid break lines etc... I'm assuming the
> > process is similar.
> > Thanks...
>
> I have always replaced and repaired tranny cooler line with the 'rubber'
> version. It works great and fits on with clamps. The also make 'high
> pressure' worm gear clamps now or I use two regular ones side by side.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> (More Off Road album links at bottom of the view page)
You're saying forget the quick-disconnect type fitting and just use
the hose with a few hose clamps? I've considered doing this...
02-12-2007, 11:21 AM
#30
Guest
Posts: n/a
Re: Where to get tranny line clip?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45d08a09$0$21646$9a6e19ea@unlimited.newshosti ng.com...
....
>
> I have always replaced and repaired tranny cooler line with the
> 'rubber' version. It works great and fits on with clamps. The
> also make 'high pressure' worm gear clamps now or I use two
> regular ones side by side.
Fuel hose for fuel injection systems should work great in this application.
Earle
news:45d08a09$0$21646$9a6e19ea@unlimited.newshosti ng.com...
....
>
> I have always replaced and repaired tranny cooler line with the
> 'rubber' version. It works great and fits on with clamps. The
> also make 'high pressure' worm gear clamps now or I use two
> regular ones side by side.
Fuel hose for fuel injection systems should work great in this application.
Earle