TJ won't start /run
Guest
Posts: n/a
Re: TJ won't start /run
scanner shows problem with camposition sensor.
I forgot to put this in original posting
"SNSPRT" <pete.brideau@verizon.net> wrote in message
news:Yy8ti.2587$I64.2475@trndny08...
>I have a 2000 TJ. It currently won't start most of the time and when it did
>start it was only after sitting over night and then would start and run
>for about 5-15 minutes depending on the temperature outside. I replaced the
>following with on luck... the crankshaft position sensor, the camshaft
>position sensor, the coil pack. when none of these work I had it towed to a
>garage who after trying some other test, replaced the PCM. But still does
>want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
>
> Pete
>
I forgot to put this in original posting
"SNSPRT" <pete.brideau@verizon.net> wrote in message
news:Yy8ti.2587$I64.2475@trndny08...
>I have a 2000 TJ. It currently won't start most of the time and when it did
>start it was only after sitting over night and then would start and run
>for about 5-15 minutes depending on the temperature outside. I replaced the
>following with on luck... the crankshaft position sensor, the camshaft
>position sensor, the coil pack. when none of these work I had it towed to a
>garage who after trying some other test, replaced the PCM. But still does
>want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
>
> Pete
>
Guest
Posts: n/a
Re: TJ won't start /run
scanner shows problem with camposition sensor.
I forgot to put this in original posting
"SNSPRT" <pete.brideau@verizon.net> wrote in message
news:Yy8ti.2587$I64.2475@trndny08...
>I have a 2000 TJ. It currently won't start most of the time and when it did
>start it was only after sitting over night and then would start and run
>for about 5-15 minutes depending on the temperature outside. I replaced the
>following with on luck... the crankshaft position sensor, the camshaft
>position sensor, the coil pack. when none of these work I had it towed to a
>garage who after trying some other test, replaced the PCM. But still does
>want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
>
> Pete
>
I forgot to put this in original posting
"SNSPRT" <pete.brideau@verizon.net> wrote in message
news:Yy8ti.2587$I64.2475@trndny08...
>I have a 2000 TJ. It currently won't start most of the time and when it did
>start it was only after sitting over night and then would start and run
>for about 5-15 minutes depending on the temperature outside. I replaced the
>following with on luck... the crankshaft position sensor, the camshaft
>position sensor, the coil pack. when none of these work I had it towed to a
>garage who after trying some other test, replaced the PCM. But still does
>want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
>
> Pete
>
Guest
Posts: n/a
Re: TJ won't start /run
scanner shows problem with camposition sensor.
I forgot to put this in original posting
"SNSPRT" <pete.brideau@verizon.net> wrote in message
news:Yy8ti.2587$I64.2475@trndny08...
>I have a 2000 TJ. It currently won't start most of the time and when it did
>start it was only after sitting over night and then would start and run
>for about 5-15 minutes depending on the temperature outside. I replaced the
>following with on luck... the crankshaft position sensor, the camshaft
>position sensor, the coil pack. when none of these work I had it towed to a
>garage who after trying some other test, replaced the PCM. But still does
>want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
>
> Pete
>
I forgot to put this in original posting
"SNSPRT" <pete.brideau@verizon.net> wrote in message
news:Yy8ti.2587$I64.2475@trndny08...
>I have a 2000 TJ. It currently won't start most of the time and when it did
>start it was only after sitting over night and then would start and run
>for about 5-15 minutes depending on the temperature outside. I replaced the
>following with on luck... the crankshaft position sensor, the camshaft
>position sensor, the coil pack. when none of these work I had it towed to a
>garage who after trying some other test, replaced the PCM. But still does
>want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
>
> Pete
>
Guest
Posts: n/a
Re: TJ won't start /run
SNSPRT wrote:
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: TJ won't start /run
SNSPRT wrote:
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: TJ won't start /run
SNSPRT wrote:
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: TJ won't start /run
SNSPRT wrote:
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> scanner shows problem with camposition sensor.
With all the problems and replaced bits you are
mentioning, I would suspect a faulty harness or
ground splice issue.
That's going to take a multimeter, disconnecting
the harness, and about 4 hours of your time to
diagnose.
These days most shops only hook up the scanner.
Problem is the scanner can't detect wiring faults
that well.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: TJ won't start /run
Can you describe more about it not starting? Do you turn the key,
hear it crank, but the engine doesn't turn? etc...
I had a problem with my 2000 TJ where that would happen. It was like
there was a fuel pump problem. It was under warranty at the time.
The dealer had NO IDEA what was wrong. They just started replacing
everything. Fuel tank (fuel pump is part of tank), PCM, etc.. They
would fix it, it wouldn't start again and I would bring it back. I
think this went of for about 2 - 3 weeks where I didn't have the car.
Eventually, I just worked.
I suspect replacing the PCM solved the issue. Overall, I think a
grounding issue or short was causing the failure.
Nick
On Aug 4, 8:09 pm, "SNSPRT" <pete.brid...@verizon.net> wrote:
> I have a 2000 TJ. It currently won't start most of the time and when it did
> start it was only after sitting over night and then would start and run for
> about 5-15 minutes depending on the temperature outside. I replaced the
> following with on luck... the crankshaft position sensor, the camshaft
> position sensor, the coil pack. when none of these work I had it towed to a
> garage who after trying some other test, replaced the PCM. But still does
> want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
> Pete
hear it crank, but the engine doesn't turn? etc...
I had a problem with my 2000 TJ where that would happen. It was like
there was a fuel pump problem. It was under warranty at the time.
The dealer had NO IDEA what was wrong. They just started replacing
everything. Fuel tank (fuel pump is part of tank), PCM, etc.. They
would fix it, it wouldn't start again and I would bring it back. I
think this went of for about 2 - 3 weeks where I didn't have the car.
Eventually, I just worked.
I suspect replacing the PCM solved the issue. Overall, I think a
grounding issue or short was causing the failure.
Nick
On Aug 4, 8:09 pm, "SNSPRT" <pete.brid...@verizon.net> wrote:
> I have a 2000 TJ. It currently won't start most of the time and when it did
> start it was only after sitting over night and then would start and run for
> about 5-15 minutes depending on the temperature outside. I replaced the
> following with on luck... the crankshaft position sensor, the camshaft
> position sensor, the coil pack. when none of these work I had it towed to a
> garage who after trying some other test, replaced the PCM. But still does
> want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
> Pete
Guest
Posts: n/a
Re: TJ won't start /run
Can you describe more about it not starting? Do you turn the key,
hear it crank, but the engine doesn't turn? etc...
I had a problem with my 2000 TJ where that would happen. It was like
there was a fuel pump problem. It was under warranty at the time.
The dealer had NO IDEA what was wrong. They just started replacing
everything. Fuel tank (fuel pump is part of tank), PCM, etc.. They
would fix it, it wouldn't start again and I would bring it back. I
think this went of for about 2 - 3 weeks where I didn't have the car.
Eventually, I just worked.
I suspect replacing the PCM solved the issue. Overall, I think a
grounding issue or short was causing the failure.
Nick
On Aug 4, 8:09 pm, "SNSPRT" <pete.brid...@verizon.net> wrote:
> I have a 2000 TJ. It currently won't start most of the time and when it did
> start it was only after sitting over night and then would start and run for
> about 5-15 minutes depending on the temperature outside. I replaced the
> following with on luck... the crankshaft position sensor, the camshaft
> position sensor, the coil pack. when none of these work I had it towed to a
> garage who after trying some other test, replaced the PCM. But still does
> want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
> Pete
hear it crank, but the engine doesn't turn? etc...
I had a problem with my 2000 TJ where that would happen. It was like
there was a fuel pump problem. It was under warranty at the time.
The dealer had NO IDEA what was wrong. They just started replacing
everything. Fuel tank (fuel pump is part of tank), PCM, etc.. They
would fix it, it wouldn't start again and I would bring it back. I
think this went of for about 2 - 3 weeks where I didn't have the car.
Eventually, I just worked.
I suspect replacing the PCM solved the issue. Overall, I think a
grounding issue or short was causing the failure.
Nick
On Aug 4, 8:09 pm, "SNSPRT" <pete.brid...@verizon.net> wrote:
> I have a 2000 TJ. It currently won't start most of the time and when it did
> start it was only after sitting over night and then would start and run for
> about 5-15 minutes depending on the temperature outside. I replaced the
> following with on luck... the crankshaft position sensor, the camshaft
> position sensor, the coil pack. when none of these work I had it towed to a
> garage who after trying some other test, replaced the PCM. But still does
> want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
> Pete
Guest
Posts: n/a
Re: TJ won't start /run
Can you describe more about it not starting? Do you turn the key,
hear it crank, but the engine doesn't turn? etc...
I had a problem with my 2000 TJ where that would happen. It was like
there was a fuel pump problem. It was under warranty at the time.
The dealer had NO IDEA what was wrong. They just started replacing
everything. Fuel tank (fuel pump is part of tank), PCM, etc.. They
would fix it, it wouldn't start again and I would bring it back. I
think this went of for about 2 - 3 weeks where I didn't have the car.
Eventually, I just worked.
I suspect replacing the PCM solved the issue. Overall, I think a
grounding issue or short was causing the failure.
Nick
On Aug 4, 8:09 pm, "SNSPRT" <pete.brid...@verizon.net> wrote:
> I have a 2000 TJ. It currently won't start most of the time and when it did
> start it was only after sitting over night and then would start and run for
> about 5-15 minutes depending on the temperature outside. I replaced the
> following with on luck... the crankshaft position sensor, the camshaft
> position sensor, the coil pack. when none of these work I had it towed to a
> garage who after trying some other test, replaced the PCM. But still does
> want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
> Pete
hear it crank, but the engine doesn't turn? etc...
I had a problem with my 2000 TJ where that would happen. It was like
there was a fuel pump problem. It was under warranty at the time.
The dealer had NO IDEA what was wrong. They just started replacing
everything. Fuel tank (fuel pump is part of tank), PCM, etc.. They
would fix it, it wouldn't start again and I would bring it back. I
think this went of for about 2 - 3 weeks where I didn't have the car.
Eventually, I just worked.
I suspect replacing the PCM solved the issue. Overall, I think a
grounding issue or short was causing the failure.
Nick
On Aug 4, 8:09 pm, "SNSPRT" <pete.brid...@verizon.net> wrote:
> I have a 2000 TJ. It currently won't start most of the time and when it did
> start it was only after sitting over night and then would start and run for
> about 5-15 minutes depending on the temperature outside. I replaced the
> following with on luck... the crankshaft position sensor, the camshaft
> position sensor, the coil pack. when none of these work I had it towed to a
> garage who after trying some other test, replaced the PCM. But still does
> want to start/run. The jeep is set up with CA emissions.
>
> Anyone have any suggestions?
>
> Thanks in advance
>
> Pete
