TJ Turn Signal Problem
#21
Guest
Posts: n/a
Re: TJ Turn Signal Problem
Scratch my comments then, I was going off CJ and YJ experience.
"IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
news:kcGpe.1955$751.1495@newssvr30.news.prodigy.co m...
> the steering wheel doesnt come off when doing a multifunction switch
>
>
> "Rusted" <no@email.com> wrote in message
> news:ePDpe.3963$kW6.41@fe21.usenetserver.com...
>> While you are at the parts store be sure to rent two tools. The steering
>> wheel puller (like a gear puller), and the tool that compresses the
>> spring
>> while you remove a clip.
>>
>> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
>> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
>> > it is probably the multi function switch... (the lever you pres up &
> down)
>> > They cost me 36 bucks from the dealer and take about 20 minutes to
>> > install!!
>> >
>> >
>> >
>> > "rafterg" <trg@openrangeinternet.com> wrote in message
>> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
>> >> I have a 1999 TJ. Blinkers don't work, either side, and no light
>> >> comes
>> >> on on the dash. Hazards don't work either. Checked the fuse. No
>> >> problem. Went and bought a new flasher unit. Installed it. No
>> >> change
>> >> at all. Any thoughts before I give up and take it in? Thank you. My
>> >> guess is now the switch itself on the steering column but I think
>> >> maybe
>> >> that is beyond my abilities and would be a lot of trouble to get into
>> >> if that is not even the problem. Not sure it is relevant but the
>> >> flasher was replaced a year or so ago for the same problem, and it
>> >> worked that time. Is it possible I just got a bad one?
>> >>
>> >
>> >
>>
>>
>>
>
>
"IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
news:kcGpe.1955$751.1495@newssvr30.news.prodigy.co m...
> the steering wheel doesnt come off when doing a multifunction switch
>
>
> "Rusted" <no@email.com> wrote in message
> news:ePDpe.3963$kW6.41@fe21.usenetserver.com...
>> While you are at the parts store be sure to rent two tools. The steering
>> wheel puller (like a gear puller), and the tool that compresses the
>> spring
>> while you remove a clip.
>>
>> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
>> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
>> > it is probably the multi function switch... (the lever you pres up &
> down)
>> > They cost me 36 bucks from the dealer and take about 20 minutes to
>> > install!!
>> >
>> >
>> >
>> > "rafterg" <trg@openrangeinternet.com> wrote in message
>> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
>> >> I have a 1999 TJ. Blinkers don't work, either side, and no light
>> >> comes
>> >> on on the dash. Hazards don't work either. Checked the fuse. No
>> >> problem. Went and bought a new flasher unit. Installed it. No
>> >> change
>> >> at all. Any thoughts before I give up and take it in? Thank you. My
>> >> guess is now the switch itself on the steering column but I think
>> >> maybe
>> >> that is beyond my abilities and would be a lot of trouble to get into
>> >> if that is not even the problem. Not sure it is relevant but the
>> >> flasher was replaced a year or so ago for the same problem, and it
>> >> worked that time. Is it possible I just got a bad one?
>> >>
>> >
>> >
>>
>>
>>
>
>
#22
Guest
Posts: n/a
Re: TJ Turn Signal Problem
you do not need those tools to replace the switch
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
#23
Guest
Posts: n/a
Re: TJ Turn Signal Problem
you do not need those tools to replace the switch
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
#24
Guest
Posts: n/a
Re: TJ Turn Signal Problem
you do not need those tools to replace the switch
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
#25
Guest
Posts: n/a
Re: TJ Turn Signal Problem
you do not need those tools to replace the switch
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
just remove the phillips screws that hold the covers on the column and then
remove the 2 torq bit screws that hold the switch in place and pull up[ward and
it's off
Rusted wrote:
> While you are at the parts store be sure to rent two tools. The steering
> wheel puller (like a gear puller), and the tool that compresses the spring
> while you remove a clip.
>
> "IsellJeeps" <jsprauer2000@yahoo.com> wrote in message
> news:HxDpe.1928$751.35@newssvr30.news.prodigy.com. ..
> > it is probably the multi function switch... (the lever you pres up & down)
> > They cost me 36 bucks from the dealer and take about 20 minutes to
> > install!!
> >
> >
> >
> > "rafterg" <trg@openrangeinternet.com> wrote in message
> > news:1118240962.694119.159070@f14g2000cwb.googlegr oups.com...
> >> I have a 1999 TJ. Blinkers don't work, either side, and no light comes
> >> on on the dash. Hazards don't work either. Checked the fuse. No
> >> problem. Went and bought a new flasher unit. Installed it. No change
> >> at all. Any thoughts before I give up and take it in? Thank you. My
> >> guess is now the switch itself on the steering column but I think maybe
> >> that is beyond my abilities and would be a lot of trouble to get into
> >> if that is not even the problem. Not sure it is relevant but the
> >> flasher was replaced a year or so ago for the same problem, and it
> >> worked that time. Is it possible I just got a bad one?
> >>
> >
> >
Thread
Thread Starter
Forum
Replies
Last Post
Simon Juncal
Jeep Mailing List
21
11-06-2003 12:38 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)