SYE problems
#1
Guest
Posts: n/a
SYE problems
Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
YJ, all seemed to go fine, as he was putting it back together directions
said to go through shifting to make sure rod doesn't stick out too far,
shifted fine while checking, but when completely back together it wont
shift. Needless to say he is a little frustrated, just wondered if anyone
had this problem and can point him in the right direction on what went wrong
so when he re-does it he wont get to the same point again.
Greg
YJ, all seemed to go fine, as he was putting it back together directions
said to go through shifting to make sure rod doesn't stick out too far,
shifted fine while checking, but when completely back together it wont
shift. Needless to say he is a little frustrated, just wondered if anyone
had this problem and can point him in the right direction on what went wrong
so when he re-does it he wont get to the same point again.
Greg
#2
Guest
Posts: n/a
Re: SYE problems
Hi Greg,
Something is miss assembled, this TJ tail shaft will be a little
different than yours, but they go together the same:
http://7slotgrille.com/tech/sye2/index.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Greg wrote:
>
> Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
> YJ, all seemed to go fine, as he was putting it back together directions
> said to go through shifting to make sure rod doesn't stick out too far,
> shifted fine while checking, but when completely back together it wont
> shift. Needless to say he is a little frustrated, just wondered if anyone
> had this problem and can point him in the right direction on what went wrong
> so when he re-does it he wont get to the same point again.
> Greg
Something is miss assembled, this TJ tail shaft will be a little
different than yours, but they go together the same:
http://7slotgrille.com/tech/sye2/index.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Greg wrote:
>
> Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
> YJ, all seemed to go fine, as he was putting it back together directions
> said to go through shifting to make sure rod doesn't stick out too far,
> shifted fine while checking, but when completely back together it wont
> shift. Needless to say he is a little frustrated, just wondered if anyone
> had this problem and can point him in the right direction on what went wrong
> so when he re-does it he wont get to the same point again.
> Greg
#3
Guest
Posts: n/a
Re: SYE problems
Hi Greg,
Something is miss assembled, this TJ tail shaft will be a little
different than yours, but they go together the same:
http://7slotgrille.com/tech/sye2/index.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Greg wrote:
>
> Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
> YJ, all seemed to go fine, as he was putting it back together directions
> said to go through shifting to make sure rod doesn't stick out too far,
> shifted fine while checking, but when completely back together it wont
> shift. Needless to say he is a little frustrated, just wondered if anyone
> had this problem and can point him in the right direction on what went wrong
> so when he re-does it he wont get to the same point again.
> Greg
Something is miss assembled, this TJ tail shaft will be a little
different than yours, but they go together the same:
http://7slotgrille.com/tech/sye2/index.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Greg wrote:
>
> Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
> YJ, all seemed to go fine, as he was putting it back together directions
> said to go through shifting to make sure rod doesn't stick out too far,
> shifted fine while checking, but when completely back together it wont
> shift. Needless to say he is a little frustrated, just wondered if anyone
> had this problem and can point him in the right direction on what went wrong
> so when he re-does it he wont get to the same point again.
> Greg
#4
Guest
Posts: n/a
Re: SYE problems
Hi Greg,
Something is miss assembled, this TJ tail shaft will be a little
different than yours, but they go together the same:
http://7slotgrille.com/tech/sye2/index.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Greg wrote:
>
> Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
> YJ, all seemed to go fine, as he was putting it back together directions
> said to go through shifting to make sure rod doesn't stick out too far,
> shifted fine while checking, but when completely back together it wont
> shift. Needless to say he is a little frustrated, just wondered if anyone
> had this problem and can point him in the right direction on what went wrong
> so when he re-does it he wont get to the same point again.
> Greg
Something is miss assembled, this TJ tail shaft will be a little
different than yours, but they go together the same:
http://7slotgrille.com/tech/sye2/index.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Greg wrote:
>
> Freind of mine was doing a slip yoke elimanator yesterday, NP 231 on an 89
> YJ, all seemed to go fine, as he was putting it back together directions
> said to go through shifting to make sure rod doesn't stick out too far,
> shifted fine while checking, but when completely back together it wont
> shift. Needless to say he is a little frustrated, just wondered if anyone
> had this problem and can point him in the right direction on what went wrong
> so when he re-does it he wont get to the same point again.
> Greg
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)