Steering column bearing
Guest
Posts: n/a
Re: Steering column bearing
Your local parts jobber would be a good start, it is an off-the-shelf GM
assembly. There's two sets of ball bearings and races, the one you're
talking about below the signal light switch and one at the bottom end of
the column tube held up with a plastic doughnut and wire C-clip. If
you're doing one...
I replaced both of mine a couple of years ago, so they are readily
available.
Mike Duane Jr. wrote:
> Hi Everyone,
>
> I replaced the steering column in my CJ with a factory tilt column but the
> shaft bearing just below the steering wheel is toast. ANy ideas where to
> get a replacement? I was thinking of trying to match up a sealed bearing as
> a replacement, any thoughts?
>
> Thanks!
>
> Mike D.
> 85 CJ7
assembly. There's two sets of ball bearings and races, the one you're
talking about below the signal light switch and one at the bottom end of
the column tube held up with a plastic doughnut and wire C-clip. If
you're doing one...
I replaced both of mine a couple of years ago, so they are readily
available.
Mike Duane Jr. wrote:
> Hi Everyone,
>
> I replaced the steering column in my CJ with a factory tilt column but the
> shaft bearing just below the steering wheel is toast. ANy ideas where to
> get a replacement? I was thinking of trying to match up a sealed bearing as
> a replacement, any thoughts?
>
> Thanks!
>
> Mike D.
> 85 CJ7
Guest
Posts: n/a
Re: Steering column bearing
Your local parts jobber would be a good start, it is an off-the-shelf GM
assembly. There's two sets of ball bearings and races, the one you're
talking about below the signal light switch and one at the bottom end of
the column tube held up with a plastic doughnut and wire C-clip. If
you're doing one...
I replaced both of mine a couple of years ago, so they are readily
available.
Mike Duane Jr. wrote:
> Hi Everyone,
>
> I replaced the steering column in my CJ with a factory tilt column but the
> shaft bearing just below the steering wheel is toast. ANy ideas where to
> get a replacement? I was thinking of trying to match up a sealed bearing as
> a replacement, any thoughts?
>
> Thanks!
>
> Mike D.
> 85 CJ7
assembly. There's two sets of ball bearings and races, the one you're
talking about below the signal light switch and one at the bottom end of
the column tube held up with a plastic doughnut and wire C-clip. If
you're doing one...
I replaced both of mine a couple of years ago, so they are readily
available.
Mike Duane Jr. wrote:
> Hi Everyone,
>
> I replaced the steering column in my CJ with a factory tilt column but the
> shaft bearing just below the steering wheel is toast. ANy ideas where to
> get a replacement? I was thinking of trying to match up a sealed bearing as
> a replacement, any thoughts?
>
> Thanks!
>
> Mike D.
> 85 CJ7
Guest
Posts: n/a
Re: Steering column bearing
Your local parts jobber would be a good start, it is an off-the-shelf GM
assembly. There's two sets of ball bearings and races, the one you're
talking about below the signal light switch and one at the bottom end of
the column tube held up with a plastic doughnut and wire C-clip. If
you're doing one...
I replaced both of mine a couple of years ago, so they are readily
available.
Mike Duane Jr. wrote:
> Hi Everyone,
>
> I replaced the steering column in my CJ with a factory tilt column but the
> shaft bearing just below the steering wheel is toast. ANy ideas where to
> get a replacement? I was thinking of trying to match up a sealed bearing as
> a replacement, any thoughts?
>
> Thanks!
>
> Mike D.
> 85 CJ7
assembly. There's two sets of ball bearings and races, the one you're
talking about below the signal light switch and one at the bottom end of
the column tube held up with a plastic doughnut and wire C-clip. If
you're doing one...
I replaced both of mine a couple of years ago, so they are readily
available.
Mike Duane Jr. wrote:
> Hi Everyone,
>
> I replaced the steering column in my CJ with a factory tilt column but the
> shaft bearing just below the steering wheel is toast. ANy ideas where to
> get a replacement? I was thinking of trying to match up a sealed bearing as
> a replacement, any thoughts?
>
> Thanks!
>
> Mike D.
> 85 CJ7
Guest
Posts: n/a
Re: Steering column bearing
What are the signs they need replacing? Ever since I got my 81 CJ 2 years
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
Guest
Posts: n/a
Re: Steering column bearing
What are the signs they need replacing? Ever since I got my 81 CJ 2 years
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
Guest
Posts: n/a
Re: Steering column bearing
What are the signs they need replacing? Ever since I got my 81 CJ 2 years
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
Guest
Posts: n/a
Re: Steering column bearing
What are the signs they need replacing? Ever since I got my 81 CJ 2 years
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
ago, there is a rattle type feel while going down the road and over bumps,
had all the steering from engine down checked 3 times, and they can't find
anything, I never thought about it being in the column, but now that I think
about it, when I drive it I feel like the if pushed on the steering column
would move, but it doesn't, just that's what the rattle type vibration feels
like while driving.
"Lee Ayrton" <layrton@panix.com> wrote in message
news:d5e1no$npq$1@reader1.panix.com...
> Your local parts jobber would be a good start, it is an off-the-shelf GM
> assembly. There's two sets of ball bearings and races, the one you're
> talking about below the signal light switch and one at the bottom end of
> the column tube held up with a plastic doughnut and wire C-clip. If
> you're doing one...
>
> I replaced both of mine a couple of years ago, so they are readily
> available.
>
>
> Mike Duane Jr. wrote:
>> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
>> column but the shaft bearing just below the steering wheel is toast. ANy
>> ideas where to get a replacement? I was thinking of trying to match up a
>> sealed bearing as a replacement, any thoughts?
>>
>> Thanks!
>>
>> Mike D.
>> 85 CJ7
>
Guest
Posts: n/a
Re: Steering column bearing
Your column has a u-joint just under the brake reservoir. These get
sloppy over time. A local suspension shop will cut that out and put a
greaseable one in for something like $150.00 or 175 if I remember right.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Greg wrote:
>
> What are the signs they need replacing? Ever since I got my 81 CJ 2 years
> ago, there is a rattle type feel while going down the road and over bumps,
> had all the steering from engine down checked 3 times, and they can't find
> anything, I never thought about it being in the column, but now that I think
> about it, when I drive it I feel like the if pushed on the steering column
> would move, but it doesn't, just that's what the rattle type vibration feels
> like while driving.
>
> "Lee Ayrton" <layrton@panix.com> wrote in message
> news:d5e1no$npq$1@reader1.panix.com...
> > Your local parts jobber would be a good start, it is an off-the-shelf GM
> > assembly. There's two sets of ball bearings and races, the one you're
> > talking about below the signal light switch and one at the bottom end of
> > the column tube held up with a plastic doughnut and wire C-clip. If
> > you're doing one...
> >
> > I replaced both of mine a couple of years ago, so they are readily
> > available.
> >
> >
> > Mike Duane Jr. wrote:
> >> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
> >> column but the shaft bearing just below the steering wheel is toast. ANy
> >> ideas where to get a replacement? I was thinking of trying to match up a
> >> sealed bearing as a replacement, any thoughts?
> >>
> >> Thanks!
> >>
> >> Mike D.
> >> 85 CJ7
> >
sloppy over time. A local suspension shop will cut that out and put a
greaseable one in for something like $150.00 or 175 if I remember right.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Greg wrote:
>
> What are the signs they need replacing? Ever since I got my 81 CJ 2 years
> ago, there is a rattle type feel while going down the road and over bumps,
> had all the steering from engine down checked 3 times, and they can't find
> anything, I never thought about it being in the column, but now that I think
> about it, when I drive it I feel like the if pushed on the steering column
> would move, but it doesn't, just that's what the rattle type vibration feels
> like while driving.
>
> "Lee Ayrton" <layrton@panix.com> wrote in message
> news:d5e1no$npq$1@reader1.panix.com...
> > Your local parts jobber would be a good start, it is an off-the-shelf GM
> > assembly. There's two sets of ball bearings and races, the one you're
> > talking about below the signal light switch and one at the bottom end of
> > the column tube held up with a plastic doughnut and wire C-clip. If
> > you're doing one...
> >
> > I replaced both of mine a couple of years ago, so they are readily
> > available.
> >
> >
> > Mike Duane Jr. wrote:
> >> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
> >> column but the shaft bearing just below the steering wheel is toast. ANy
> >> ideas where to get a replacement? I was thinking of trying to match up a
> >> sealed bearing as a replacement, any thoughts?
> >>
> >> Thanks!
> >>
> >> Mike D.
> >> 85 CJ7
> >
Guest
Posts: n/a
Re: Steering column bearing
Your column has a u-joint just under the brake reservoir. These get
sloppy over time. A local suspension shop will cut that out and put a
greaseable one in for something like $150.00 or 175 if I remember right.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Greg wrote:
>
> What are the signs they need replacing? Ever since I got my 81 CJ 2 years
> ago, there is a rattle type feel while going down the road and over bumps,
> had all the steering from engine down checked 3 times, and they can't find
> anything, I never thought about it being in the column, but now that I think
> about it, when I drive it I feel like the if pushed on the steering column
> would move, but it doesn't, just that's what the rattle type vibration feels
> like while driving.
>
> "Lee Ayrton" <layrton@panix.com> wrote in message
> news:d5e1no$npq$1@reader1.panix.com...
> > Your local parts jobber would be a good start, it is an off-the-shelf GM
> > assembly. There's two sets of ball bearings and races, the one you're
> > talking about below the signal light switch and one at the bottom end of
> > the column tube held up with a plastic doughnut and wire C-clip. If
> > you're doing one...
> >
> > I replaced both of mine a couple of years ago, so they are readily
> > available.
> >
> >
> > Mike Duane Jr. wrote:
> >> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
> >> column but the shaft bearing just below the steering wheel is toast. ANy
> >> ideas where to get a replacement? I was thinking of trying to match up a
> >> sealed bearing as a replacement, any thoughts?
> >>
> >> Thanks!
> >>
> >> Mike D.
> >> 85 CJ7
> >
sloppy over time. A local suspension shop will cut that out and put a
greaseable one in for something like $150.00 or 175 if I remember right.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Greg wrote:
>
> What are the signs they need replacing? Ever since I got my 81 CJ 2 years
> ago, there is a rattle type feel while going down the road and over bumps,
> had all the steering from engine down checked 3 times, and they can't find
> anything, I never thought about it being in the column, but now that I think
> about it, when I drive it I feel like the if pushed on the steering column
> would move, but it doesn't, just that's what the rattle type vibration feels
> like while driving.
>
> "Lee Ayrton" <layrton@panix.com> wrote in message
> news:d5e1no$npq$1@reader1.panix.com...
> > Your local parts jobber would be a good start, it is an off-the-shelf GM
> > assembly. There's two sets of ball bearings and races, the one you're
> > talking about below the signal light switch and one at the bottom end of
> > the column tube held up with a plastic doughnut and wire C-clip. If
> > you're doing one...
> >
> > I replaced both of mine a couple of years ago, so they are readily
> > available.
> >
> >
> > Mike Duane Jr. wrote:
> >> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
> >> column but the shaft bearing just below the steering wheel is toast. ANy
> >> ideas where to get a replacement? I was thinking of trying to match up a
> >> sealed bearing as a replacement, any thoughts?
> >>
> >> Thanks!
> >>
> >> Mike D.
> >> 85 CJ7
> >
Guest
Posts: n/a
Re: Steering column bearing
Your column has a u-joint just under the brake reservoir. These get
sloppy over time. A local suspension shop will cut that out and put a
greaseable one in for something like $150.00 or 175 if I remember right.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Greg wrote:
>
> What are the signs they need replacing? Ever since I got my 81 CJ 2 years
> ago, there is a rattle type feel while going down the road and over bumps,
> had all the steering from engine down checked 3 times, and they can't find
> anything, I never thought about it being in the column, but now that I think
> about it, when I drive it I feel like the if pushed on the steering column
> would move, but it doesn't, just that's what the rattle type vibration feels
> like while driving.
>
> "Lee Ayrton" <layrton@panix.com> wrote in message
> news:d5e1no$npq$1@reader1.panix.com...
> > Your local parts jobber would be a good start, it is an off-the-shelf GM
> > assembly. There's two sets of ball bearings and races, the one you're
> > talking about below the signal light switch and one at the bottom end of
> > the column tube held up with a plastic doughnut and wire C-clip. If
> > you're doing one...
> >
> > I replaced both of mine a couple of years ago, so they are readily
> > available.
> >
> >
> > Mike Duane Jr. wrote:
> >> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
> >> column but the shaft bearing just below the steering wheel is toast. ANy
> >> ideas where to get a replacement? I was thinking of trying to match up a
> >> sealed bearing as a replacement, any thoughts?
> >>
> >> Thanks!
> >>
> >> Mike D.
> >> 85 CJ7
> >
sloppy over time. A local suspension shop will cut that out and put a
greaseable one in for something like $150.00 or 175 if I remember right.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Greg wrote:
>
> What are the signs they need replacing? Ever since I got my 81 CJ 2 years
> ago, there is a rattle type feel while going down the road and over bumps,
> had all the steering from engine down checked 3 times, and they can't find
> anything, I never thought about it being in the column, but now that I think
> about it, when I drive it I feel like the if pushed on the steering column
> would move, but it doesn't, just that's what the rattle type vibration feels
> like while driving.
>
> "Lee Ayrton" <layrton@panix.com> wrote in message
> news:d5e1no$npq$1@reader1.panix.com...
> > Your local parts jobber would be a good start, it is an off-the-shelf GM
> > assembly. There's two sets of ball bearings and races, the one you're
> > talking about below the signal light switch and one at the bottom end of
> > the column tube held up with a plastic doughnut and wire C-clip. If
> > you're doing one...
> >
> > I replaced both of mine a couple of years ago, so they are readily
> > available.
> >
> >
> > Mike Duane Jr. wrote:
> >> Hi Everyone, I replaced the steering column in my CJ with a factory tilt
> >> column but the shaft bearing just below the steering wheel is toast. ANy
> >> ideas where to get a replacement? I was thinking of trying to match up a
> >> sealed bearing as a replacement, any thoughts?
> >>
> >> Thanks!
> >>
> >> Mike D.
> >> 85 CJ7
> >
