soft top clear moonroof
11-23-2006, 04:13 PM
#241
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
So which gasket did you use?
"Simon Juncal" <SPAMERSSUCK@usefirstinitialandlastnameATerols.com > wrote in
message news:lfydne6BRtUkVfjYnZ2dnUVZ_sadnZ2d@rcn.net...
> L.W.(Bill) ------ III wrote:
>> So did you use the gasket that fits the 258 CID intake manifold or
>> 4.0L Head?: http://www.----------.com/temp/258.4LheaderGaskets.jpg God
>> Bless America, Bill O|||||||O
>
> Honestly could you look more stupid? You're insisting you're right even
> though I (and hundreds of CJ7 and early YJ owners) have done this, and
> YOU'VE NEVER DONE IT! Whats more, if you weren't such a bull headed moron
> you could continue web searching and find more examples of a 4.0 head swap
> using the 258 carb manifold and either a TBI injection or carb.
>
> Like:
> Webber carb and OEM 258 2bbl on a 4.0 head:
> http://www.northeastsurf.com/4.0%20head%208.JPG
> Note: you can tell it's a 4.0 head because the exhaust ports are low on
> the head
> Howell Throttle body Injection on OEM 2bbl intake:
> http://www.bustedjeep.com/projects/rebuild/DCP_0992.JPG
> Here's someone who did the swap and used an aftermarket Clifford 4bbl
> intake that is made for carbed 258's
> http://www.cjoffroad.com/forums/topic.asp?TOPIC_ID=4669
>
> Some people had to mod brackets, some had to grind on the 258 intake for
> header clearance, some had to make the washers bigger for the mounting
> bolts (I did) and one guy hammered his band new borla stainless steel
> header to clearance the 258 intake. I ground on the intake to clear the
> header, because mine no longer needed the coolant jacket due to bypassing
> the intake coolant passages. Which is also why I have a cherokee
> thermostat housing (for the TBI's coolant temp sensor)
>
> --
> Simon
> "I may be wrong, but I'm not uncertain." -- Robert A. Heinlein
"Simon Juncal" <SPAMERSSUCK@usefirstinitialandlastnameATerols.com > wrote in
message news:lfydne6BRtUkVfjYnZ2dnUVZ_sadnZ2d@rcn.net...
> L.W.(Bill) ------ III wrote:
>> So did you use the gasket that fits the 258 CID intake manifold or
>> 4.0L Head?: http://www.----------.com/temp/258.4LheaderGaskets.jpg God
>> Bless America, Bill O|||||||O
>
> Honestly could you look more stupid? You're insisting you're right even
> though I (and hundreds of CJ7 and early YJ owners) have done this, and
> YOU'VE NEVER DONE IT! Whats more, if you weren't such a bull headed moron
> you could continue web searching and find more examples of a 4.0 head swap
> using the 258 carb manifold and either a TBI injection or carb.
>
> Like:
> Webber carb and OEM 258 2bbl on a 4.0 head:
> http://www.northeastsurf.com/4.0%20head%208.JPG
> Note: you can tell it's a 4.0 head because the exhaust ports are low on
> the head
> Howell Throttle body Injection on OEM 2bbl intake:
> http://www.bustedjeep.com/projects/rebuild/DCP_0992.JPG
> Here's someone who did the swap and used an aftermarket Clifford 4bbl
> intake that is made for carbed 258's
> http://www.cjoffroad.com/forums/topic.asp?TOPIC_ID=4669
>
> Some people had to mod brackets, some had to grind on the 258 intake for
> header clearance, some had to make the washers bigger for the mounting
> bolts (I did) and one guy hammered his band new borla stainless steel
> header to clearance the 258 intake. I ground on the intake to clear the
> header, because mine no longer needed the coolant jacket due to bypassing
> the intake coolant passages. Which is also why I have a cherokee
> thermostat housing (for the TBI's coolant temp sensor)
>
> --
> Simon
> "I may be wrong, but I'm not uncertain." -- Robert A. Heinlein
11-23-2006, 11:18 PM
#242
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
I would say neither of the stock gaskets would work, as the links
he provided appear to be aftermarket aluminum manifolds, one the bolt
goes right through the flange rather than clamping a bridge between the
exhaust and intake. They are not the Stock cast iron carburetor
manifolds he said they where. I would bet a shop installed the head for
him.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
billy ray wrote:
>
> So which gasket did you use?
he provided appear to be aftermarket aluminum manifolds, one the bolt
goes right through the flange rather than clamping a bridge between the
exhaust and intake. They are not the Stock cast iron carburetor
manifolds he said they where. I would bet a shop installed the head for
him.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
billy ray wrote:
>
> So which gasket did you use?
11-23-2006, 11:18 PM
#243
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
I would say neither of the stock gaskets would work, as the links
he provided appear to be aftermarket aluminum manifolds, one the bolt
goes right through the flange rather than clamping a bridge between the
exhaust and intake. They are not the Stock cast iron carburetor
manifolds he said they where. I would bet a shop installed the head for
him.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
billy ray wrote:
>
> So which gasket did you use?
he provided appear to be aftermarket aluminum manifolds, one the bolt
goes right through the flange rather than clamping a bridge between the
exhaust and intake. They are not the Stock cast iron carburetor
manifolds he said they where. I would bet a shop installed the head for
him.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
billy ray wrote:
>
> So which gasket did you use?
11-23-2006, 11:18 PM
#244
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
I would say neither of the stock gaskets would work, as the links
he provided appear to be aftermarket aluminum manifolds, one the bolt
goes right through the flange rather than clamping a bridge between the
exhaust and intake. They are not the Stock cast iron carburetor
manifolds he said they where. I would bet a shop installed the head for
him.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
billy ray wrote:
>
> So which gasket did you use?
he provided appear to be aftermarket aluminum manifolds, one the bolt
goes right through the flange rather than clamping a bridge between the
exhaust and intake. They are not the Stock cast iron carburetor
manifolds he said they where. I would bet a shop installed the head for
him.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
billy ray wrote:
>
> So which gasket did you use?
11-24-2006, 12:39 AM
#245
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
On Thu, 23 Nov 2006 20:18:08 -0800, "L.W.(Bill) ------ III"
<----------@***.net> wrote:
> I would say neither of the stock gaskets would work, as the links
>he provided appear to be aftermarket aluminum manifolds, one the bolt
>goes right through the flange rather than clamping a bridge between the
>exhaust and intake. They are not the Stock cast iron carburetor
>manifolds he said they where. I would bet a shop installed the head for
>him.
Stock cast iron carburetor manifolds? Did you skip your meds again
Bill?
> God Bless America, Bill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>billy ray wrote:
>>
>> So which gasket did you use?
<----------@***.net> wrote:
> I would say neither of the stock gaskets would work, as the links
>he provided appear to be aftermarket aluminum manifolds, one the bolt
>goes right through the flange rather than clamping a bridge between the
>exhaust and intake. They are not the Stock cast iron carburetor
>manifolds he said they where. I would bet a shop installed the head for
>him.
Stock cast iron carburetor manifolds? Did you skip your meds again
Bill?
> God Bless America, Bill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>billy ray wrote:
>>
>> So which gasket did you use?
11-24-2006, 12:39 AM
#246
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
On Thu, 23 Nov 2006 20:18:08 -0800, "L.W.(Bill) ------ III"
<----------@***.net> wrote:
> I would say neither of the stock gaskets would work, as the links
>he provided appear to be aftermarket aluminum manifolds, one the bolt
>goes right through the flange rather than clamping a bridge between the
>exhaust and intake. They are not the Stock cast iron carburetor
>manifolds he said they where. I would bet a shop installed the head for
>him.
Stock cast iron carburetor manifolds? Did you skip your meds again
Bill?
> God Bless America, Bill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>billy ray wrote:
>>
>> So which gasket did you use?
<----------@***.net> wrote:
> I would say neither of the stock gaskets would work, as the links
>he provided appear to be aftermarket aluminum manifolds, one the bolt
>goes right through the flange rather than clamping a bridge between the
>exhaust and intake. They are not the Stock cast iron carburetor
>manifolds he said they where. I would bet a shop installed the head for
>him.
Stock cast iron carburetor manifolds? Did you skip your meds again
Bill?
> God Bless America, Bill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>billy ray wrote:
>>
>> So which gasket did you use?
11-24-2006, 12:39 AM
#247
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
On Thu, 23 Nov 2006 20:18:08 -0800, "L.W.(Bill) ------ III"
<----------@***.net> wrote:
> I would say neither of the stock gaskets would work, as the links
>he provided appear to be aftermarket aluminum manifolds, one the bolt
>goes right through the flange rather than clamping a bridge between the
>exhaust and intake. They are not the Stock cast iron carburetor
>manifolds he said they where. I would bet a shop installed the head for
>him.
Stock cast iron carburetor manifolds? Did you skip your meds again
Bill?
> God Bless America, Bill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>billy ray wrote:
>>
>> So which gasket did you use?
<----------@***.net> wrote:
> I would say neither of the stock gaskets would work, as the links
>he provided appear to be aftermarket aluminum manifolds, one the bolt
>goes right through the flange rather than clamping a bridge between the
>exhaust and intake. They are not the Stock cast iron carburetor
>manifolds he said they where. I would bet a shop installed the head for
>him.
Stock cast iron carburetor manifolds? Did you skip your meds again
Bill?
> God Bless America, Bill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>billy ray wrote:
>>
>> So which gasket did you use?
11-24-2006, 06:21 AM
#248
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
Looks like cast iron to me:
http://www.----------.com/temp/258head.gif
God Bless America, Bill O|||||||O
mailto:--------------------
bllsht wrote:
>
> Stock cast iron carburetor manifolds? Did you skip your meds again
> Bill?
http://www.----------.com/temp/258head.gif
God Bless America, Bill O|||||||O
mailto:--------------------
bllsht wrote:
>
> Stock cast iron carburetor manifolds? Did you skip your meds again
> Bill?
11-24-2006, 06:21 AM
#249
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
Looks like cast iron to me:
http://www.----------.com/temp/258head.gif
God Bless America, Bill O|||||||O
mailto:--------------------
bllsht wrote:
>
> Stock cast iron carburetor manifolds? Did you skip your meds again
> Bill?
http://www.----------.com/temp/258head.gif
God Bless America, Bill O|||||||O
mailto:--------------------
bllsht wrote:
>
> Stock cast iron carburetor manifolds? Did you skip your meds again
> Bill?
11-24-2006, 06:21 AM
#250
Guest
Posts: n/a
Re: Senile ol bill proving his ignorance again
Looks like cast iron to me:
http://www.----------.com/temp/258head.gif
God Bless America, Bill O|||||||O
mailto:--------------------
bllsht wrote:
>
> Stock cast iron carburetor manifolds? Did you skip your meds again
> Bill?
http://www.----------.com/temp/258head.gif
God Bless America, Bill O|||||||O
mailto:--------------------
bllsht wrote:
>
> Stock cast iron carburetor manifolds? Did you skip your meds again
> Bill?
