Snapped off an exhaust bolt
02-01-2007, 09:57 AM
#51
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Richard J Kinch wrote:
> wb writes:
>
>> Should I
>> be able to unscrew it from the manifold fitting, assuming I get it hot
>> enough and soak it enough with the right kind of lubricant?
>
> No. It's a splined press-fit stud like on a wheel hub, not a threaded
> fastener. You have to press it out (if the assembly is on a workbench) or
> drill it out (if the assembly is on the car). Forget the advice from the
> more-macho-than-thou types about rusty bolt extraction.
Since when?
I have removed more exhaust studs than I care to remember over the years
and have 'never' seen or heard of a pressed fit exhaust stud in any
vehicle I have been exposed to.
I also have removed a couple 80's YJ ones...
The replacements come in kits with the special brass nuts.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> wb writes:
>
>> Should I
>> be able to unscrew it from the manifold fitting, assuming I get it hot
>> enough and soak it enough with the right kind of lubricant?
>
> No. It's a splined press-fit stud like on a wheel hub, not a threaded
> fastener. You have to press it out (if the assembly is on a workbench) or
> drill it out (if the assembly is on the car). Forget the advice from the
> more-macho-than-thou types about rusty bolt extraction.
Since when?
I have removed more exhaust studs than I care to remember over the years
and have 'never' seen or heard of a pressed fit exhaust stud in any
vehicle I have been exposed to.
I also have removed a couple 80's YJ ones...
The replacements come in kits with the special brass nuts.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-01-2007, 09:57 AM
#52
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Richard J Kinch wrote:
> wb writes:
>
>> Should I
>> be able to unscrew it from the manifold fitting, assuming I get it hot
>> enough and soak it enough with the right kind of lubricant?
>
> No. It's a splined press-fit stud like on a wheel hub, not a threaded
> fastener. You have to press it out (if the assembly is on a workbench) or
> drill it out (if the assembly is on the car). Forget the advice from the
> more-macho-than-thou types about rusty bolt extraction.
Since when?
I have removed more exhaust studs than I care to remember over the years
and have 'never' seen or heard of a pressed fit exhaust stud in any
vehicle I have been exposed to.
I also have removed a couple 80's YJ ones...
The replacements come in kits with the special brass nuts.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> wb writes:
>
>> Should I
>> be able to unscrew it from the manifold fitting, assuming I get it hot
>> enough and soak it enough with the right kind of lubricant?
>
> No. It's a splined press-fit stud like on a wheel hub, not a threaded
> fastener. You have to press it out (if the assembly is on a workbench) or
> drill it out (if the assembly is on the car). Forget the advice from the
> more-macho-than-thou types about rusty bolt extraction.
Since when?
I have removed more exhaust studs than I care to remember over the years
and have 'never' seen or heard of a pressed fit exhaust stud in any
vehicle I have been exposed to.
I also have removed a couple 80's YJ ones...
The replacements come in kits with the special brass nuts.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-01-2007, 09:57 AM
#53
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Richard J Kinch wrote:
> wb writes:
>
>> Should I
>> be able to unscrew it from the manifold fitting, assuming I get it hot
>> enough and soak it enough with the right kind of lubricant?
>
> No. It's a splined press-fit stud like on a wheel hub, not a threaded
> fastener. You have to press it out (if the assembly is on a workbench) or
> drill it out (if the assembly is on the car). Forget the advice from the
> more-macho-than-thou types about rusty bolt extraction.
Since when?
I have removed more exhaust studs than I care to remember over the years
and have 'never' seen or heard of a pressed fit exhaust stud in any
vehicle I have been exposed to.
I also have removed a couple 80's YJ ones...
The replacements come in kits with the special brass nuts.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> wb writes:
>
>> Should I
>> be able to unscrew it from the manifold fitting, assuming I get it hot
>> enough and soak it enough with the right kind of lubricant?
>
> No. It's a splined press-fit stud like on a wheel hub, not a threaded
> fastener. You have to press it out (if the assembly is on a workbench) or
> drill it out (if the assembly is on the car). Forget the advice from the
> more-macho-than-thou types about rusty bolt extraction.
Since when?
I have removed more exhaust studs than I care to remember over the years
and have 'never' seen or heard of a pressed fit exhaust stud in any
vehicle I have been exposed to.
I also have removed a couple 80's YJ ones...
The replacements come in kits with the special brass nuts.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-01-2007, 12:46 PM
#54
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Mike Romain writes:
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
02-01-2007, 12:46 PM
#55
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Mike Romain writes:
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
02-01-2007, 12:46 PM
#56
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Mike Romain writes:
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
02-01-2007, 12:46 PM
#57
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Mike Romain writes:
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
> I have removed more exhaust studs than I care to remember over the years
> and have 'never' seen or heard of a pressed fit exhaust stud in any
> vehicle I have been exposed to.
You must be thinking about something else.
We're talking about the manifold to pipe connector.
Here's the version NAPA sells for the TJ, part BK 6003227:
http://partimages2.genpt.com/partimages/235194.jpg
02-01-2007, 01:28 PM
#58
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Richard J Kinch wrote:
> Mike Romain writes:
>
>> I have removed more exhaust studs than I care to remember over the years
>> and have 'never' seen or heard of a pressed fit exhaust stud in any
>> vehicle I have been exposed to.
>
> You must be thinking about something else.
>
> We're talking about the manifold to pipe connector.
>
> Here's the version NAPA sells for the TJ, part BK 6003227:
>
> http://partimages2.genpt.com/partimages/235194.jpg
Good lord, you are now telling me the $tealerships just came up with
another way to screw you out of big bucks by replacing a screw stud with
a press fit that needs a freaking machine shop to fix? It also has what
looks like a steel nut which is pretty much guaranteed to rust weld it
making removal impossible.
When did they start this rip off?
I would guess with the TJ?
The YJ 258 uses screw studs and brass nuts as far as I have seen and I
have taken a couple apart. I sure didn't notice heads in there.
Your NAPA link is for a TJ, not a YJ.
Mike
> Mike Romain writes:
>
>> I have removed more exhaust studs than I care to remember over the years
>> and have 'never' seen or heard of a pressed fit exhaust stud in any
>> vehicle I have been exposed to.
>
> You must be thinking about something else.
>
> We're talking about the manifold to pipe connector.
>
> Here's the version NAPA sells for the TJ, part BK 6003227:
>
> http://partimages2.genpt.com/partimages/235194.jpg
Good lord, you are now telling me the $tealerships just came up with
another way to screw you out of big bucks by replacing a screw stud with
a press fit that needs a freaking machine shop to fix? It also has what
looks like a steel nut which is pretty much guaranteed to rust weld it
making removal impossible.
When did they start this rip off?
I would guess with the TJ?
The YJ 258 uses screw studs and brass nuts as far as I have seen and I
have taken a couple apart. I sure didn't notice heads in there.
Your NAPA link is for a TJ, not a YJ.
Mike
02-01-2007, 01:28 PM
#59
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Richard J Kinch wrote:
> Mike Romain writes:
>
>> I have removed more exhaust studs than I care to remember over the years
>> and have 'never' seen or heard of a pressed fit exhaust stud in any
>> vehicle I have been exposed to.
>
> You must be thinking about something else.
>
> We're talking about the manifold to pipe connector.
>
> Here's the version NAPA sells for the TJ, part BK 6003227:
>
> http://partimages2.genpt.com/partimages/235194.jpg
Good lord, you are now telling me the $tealerships just came up with
another way to screw you out of big bucks by replacing a screw stud with
a press fit that needs a freaking machine shop to fix? It also has what
looks like a steel nut which is pretty much guaranteed to rust weld it
making removal impossible.
When did they start this rip off?
I would guess with the TJ?
The YJ 258 uses screw studs and brass nuts as far as I have seen and I
have taken a couple apart. I sure didn't notice heads in there.
Your NAPA link is for a TJ, not a YJ.
Mike
> Mike Romain writes:
>
>> I have removed more exhaust studs than I care to remember over the years
>> and have 'never' seen or heard of a pressed fit exhaust stud in any
>> vehicle I have been exposed to.
>
> You must be thinking about something else.
>
> We're talking about the manifold to pipe connector.
>
> Here's the version NAPA sells for the TJ, part BK 6003227:
>
> http://partimages2.genpt.com/partimages/235194.jpg
Good lord, you are now telling me the $tealerships just came up with
another way to screw you out of big bucks by replacing a screw stud with
a press fit that needs a freaking machine shop to fix? It also has what
looks like a steel nut which is pretty much guaranteed to rust weld it
making removal impossible.
When did they start this rip off?
I would guess with the TJ?
The YJ 258 uses screw studs and brass nuts as far as I have seen and I
have taken a couple apart. I sure didn't notice heads in there.
Your NAPA link is for a TJ, not a YJ.
Mike
02-01-2007, 01:28 PM
#60
Guest
Posts: n/a
Re: Snapped off an exhaust bolt
Richard J Kinch wrote:
> Mike Romain writes:
>
>> I have removed more exhaust studs than I care to remember over the years
>> and have 'never' seen or heard of a pressed fit exhaust stud in any
>> vehicle I have been exposed to.
>
> You must be thinking about something else.
>
> We're talking about the manifold to pipe connector.
>
> Here's the version NAPA sells for the TJ, part BK 6003227:
>
> http://partimages2.genpt.com/partimages/235194.jpg
Good lord, you are now telling me the $tealerships just came up with
another way to screw you out of big bucks by replacing a screw stud with
a press fit that needs a freaking machine shop to fix? It also has what
looks like a steel nut which is pretty much guaranteed to rust weld it
making removal impossible.
When did they start this rip off?
I would guess with the TJ?
The YJ 258 uses screw studs and brass nuts as far as I have seen and I
have taken a couple apart. I sure didn't notice heads in there.
Your NAPA link is for a TJ, not a YJ.
Mike
> Mike Romain writes:
>
>> I have removed more exhaust studs than I care to remember over the years
>> and have 'never' seen or heard of a pressed fit exhaust stud in any
>> vehicle I have been exposed to.
>
> You must be thinking about something else.
>
> We're talking about the manifold to pipe connector.
>
> Here's the version NAPA sells for the TJ, part BK 6003227:
>
> http://partimages2.genpt.com/partimages/235194.jpg
Good lord, you are now telling me the $tealerships just came up with
another way to screw you out of big bucks by replacing a screw stud with
a press fit that needs a freaking machine shop to fix? It also has what
looks like a steel nut which is pretty much guaranteed to rust weld it
making removal impossible.
When did they start this rip off?
I would guess with the TJ?
The YJ 258 uses screw studs and brass nuts as far as I have seen and I
have taken a couple apart. I sure didn't notice heads in there.
Your NAPA link is for a TJ, not a YJ.
Mike