slight vibration after 2 inch lift
#21
Guest
Posts: n/a
Re: slight vibration after 2 inch lift
Thanks,
I ordered the Transfer case kit and the relocation bracket for the shifter.
Hopefully I will have it by Saturday, I am already having jeep withdrawals!!
"Jeff Strickland" <spamcatcher@yahoo.net> wrote in message
news:Y_ydnRc6e9MG3sHfRVn-sg@ez2.net...
> It depends on how far you drive it. You should drive something else until
> Saturday ...
>
>
>
>
>
>
>
> "John" <jstio@optonline.net> wrote in message
> news:8wF6e.1272$E21.359@fe12.lga...
>> No, i Didn't.
>>
>> Will it cause any harm i drive until I install the Tcase drop kit.?
>> "Jeff Strickland" <spamcatcher@yahoo.net> wrote in message
>> news:fLudndfVS7E6R8ffRVn-jQ@ez2.net...
>> > Did you install the tcase drop kit? You raised the drive train, and
>> > this
>> > changes the angles of the driveshaft. The tcase drop kit sets the
>> > drivetrain
>> > angles back where they belong.
>> >
>> >
>> >
>> >
>> > "John" <jstio@optonline.net> wrote in message
>> > news:KNA6e.56$7o1.21@fe09.lga...
>> >> HI All,
>> >>
>> >> I just installed a 2 inch lift, springs and shocks. Everything feels
>> > tight,
>> >> except there is a slight vibration from the rear between 25 and 35 mph
>> >> during acceleration. Its livable, but is it doing any damage? If so,
> how
>> > can
>> >> I eliminate it?
>> >>
>> >>
>> >
>> >
>>
>>
>
>
I ordered the Transfer case kit and the relocation bracket for the shifter.
Hopefully I will have it by Saturday, I am already having jeep withdrawals!!
"Jeff Strickland" <spamcatcher@yahoo.net> wrote in message
news:Y_ydnRc6e9MG3sHfRVn-sg@ez2.net...
> It depends on how far you drive it. You should drive something else until
> Saturday ...
>
>
>
>
>
>
>
> "John" <jstio@optonline.net> wrote in message
> news:8wF6e.1272$E21.359@fe12.lga...
>> No, i Didn't.
>>
>> Will it cause any harm i drive until I install the Tcase drop kit.?
>> "Jeff Strickland" <spamcatcher@yahoo.net> wrote in message
>> news:fLudndfVS7E6R8ffRVn-jQ@ez2.net...
>> > Did you install the tcase drop kit? You raised the drive train, and
>> > this
>> > changes the angles of the driveshaft. The tcase drop kit sets the
>> > drivetrain
>> > angles back where they belong.
>> >
>> >
>> >
>> >
>> > "John" <jstio@optonline.net> wrote in message
>> > news:KNA6e.56$7o1.21@fe09.lga...
>> >> HI All,
>> >>
>> >> I just installed a 2 inch lift, springs and shocks. Everything feels
>> > tight,
>> >> except there is a slight vibration from the rear between 25 and 35 mph
>> >> during acceleration. Its livable, but is it doing any damage? If so,
> how
>> > can
>> >> I eliminate it?
>> >>
>> >>
>> >
>> >
>>
>>
>
>
#26
Guest
Posts: n/a
Re: slight vibration after 2 inch lift
Quadratec has it.
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
#27
Guest
Posts: n/a
Re: slight vibration after 2 inch lift
Quadratec has it.
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
#28
Guest
Posts: n/a
Re: slight vibration after 2 inch lift
Quadratec has it.
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
#29
Guest
Posts: n/a
Re: slight vibration after 2 inch lift
Quadratec has it.
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
The kit comes with a new mount for the transmission. But i found that you
only need it if you are using the Skyjacker lowered Skid plate. If you are
using the stock Transfer case skid plate and the 2 red bars from Skyjacker,
you do not need the transmision bracket. I would call up quadratec and see
if you can order a kit without it. Save some money.
Also be prepaired, you have to cut one of the linkages and get it welded to
make it shorter.
<sleddog05468@NOSPAMyahoo.com> wrote in message
news:4269e212.322109843@news.intergate.com...
> On Wed, 13 Apr 2005 01:01:41 -0400, "John" <jstio@optonline.net>
> wrote:
>
>>Thanks,
>>I ordered the Transfer case kit and the relocation bracket for the
>>shifter.
> Where did you order a bracket for the shifter?
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)