Sheet metal & Jeep question
#31
Guest
Posts: n/a
Re: Sheet metal & Jeep question
cut out the letters in duct tape then clear coat it!
"Jeepers" <moomesa@INVALIDfnbnet.net> wrote in message
news:moomesa-332FAE.11294915012005@news-east.newsfeeds.com...
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
> --
> Member AAAAAAAA
> American Association Against Acronym Abuse And Also Ambiguity.
>
> ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
> News==----
> http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
> Newsgroups
> ----= East and West-Coast Server Farms - Total Privacy via Encryption
> =----
"Jeepers" <moomesa@INVALIDfnbnet.net> wrote in message
news:moomesa-332FAE.11294915012005@news-east.newsfeeds.com...
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
> --
> Member AAAAAAAA
> American Association Against Acronym Abuse And Also Ambiguity.
>
> ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
> News==----
> http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
> Newsgroups
> ----= East and West-Coast Server Farms - Total Privacy via Encryption
> =----
#32
Guest
Posts: n/a
Re: Sheet metal & Jeep question
On Sat, 15 Jan 2005 11:29:50 -0600, Jeepers
<moomesa@INVALIDfnbnet.net> wrote:
>The words "Jeep" on the side of Jeep CJs is embossed with the letters
>painted on top. Actually the raised surface is more like Joop with the
>'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
>toying with the idea of adding the word "Deere" below the word "Jeep",
>on raised sheetmetal like the original. I suppose it would look like
>"Dooro" then the letters would go on top.
>
>I considered bondo, but I don't think it would work at that thickness. I
>might be able to do it in lead and I even considered doing it with a
>body hammer, carefully. I have the skills, but I'm afraid that I might
>get the sheetmetal too thin after I sand & grind.
>
>Any ideas or suggestions?
Along with the sand bag and pitch suggestions I would add that a shot
bag might be better. The shot bag is a leather bag filled with lead
shot. The bag is made of three pieces. Two discs and a strip of
leather. The discs are sewn to the strip to make a round bag with
straight sides. But what may work better is to cut letters out of
sheet that is as thick as the depression is deep. The letters should
have the edges radiused on one side. Then, press the letters into the
back side of the sheetmetal while supporting the the other side with
polyurethane. See http://www.bonnydoonengineering.com/ for an
explanation of this process.
ERS
<moomesa@INVALIDfnbnet.net> wrote:
>The words "Jeep" on the side of Jeep CJs is embossed with the letters
>painted on top. Actually the raised surface is more like Joop with the
>'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
>toying with the idea of adding the word "Deere" below the word "Jeep",
>on raised sheetmetal like the original. I suppose it would look like
>"Dooro" then the letters would go on top.
>
>I considered bondo, but I don't think it would work at that thickness. I
>might be able to do it in lead and I even considered doing it with a
>body hammer, carefully. I have the skills, but I'm afraid that I might
>get the sheetmetal too thin after I sand & grind.
>
>Any ideas or suggestions?
Along with the sand bag and pitch suggestions I would add that a shot
bag might be better. The shot bag is a leather bag filled with lead
shot. The bag is made of three pieces. Two discs and a strip of
leather. The discs are sewn to the strip to make a round bag with
straight sides. But what may work better is to cut letters out of
sheet that is as thick as the depression is deep. The letters should
have the edges radiused on one side. Then, press the letters into the
back side of the sheetmetal while supporting the the other side with
polyurethane. See http://www.bonnydoonengineering.com/ for an
explanation of this process.
ERS
#33
Guest
Posts: n/a
Re: Sheet metal & Jeep question
On Sat, 15 Jan 2005 11:29:50 -0600, Jeepers
<moomesa@INVALIDfnbnet.net> wrote:
>The words "Jeep" on the side of Jeep CJs is embossed with the letters
>painted on top. Actually the raised surface is more like Joop with the
>'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
>toying with the idea of adding the word "Deere" below the word "Jeep",
>on raised sheetmetal like the original. I suppose it would look like
>"Dooro" then the letters would go on top.
>
>I considered bondo, but I don't think it would work at that thickness. I
>might be able to do it in lead and I even considered doing it with a
>body hammer, carefully. I have the skills, but I'm afraid that I might
>get the sheetmetal too thin after I sand & grind.
>
>Any ideas or suggestions?
Along with the sand bag and pitch suggestions I would add that a shot
bag might be better. The shot bag is a leather bag filled with lead
shot. The bag is made of three pieces. Two discs and a strip of
leather. The discs are sewn to the strip to make a round bag with
straight sides. But what may work better is to cut letters out of
sheet that is as thick as the depression is deep. The letters should
have the edges radiused on one side. Then, press the letters into the
back side of the sheetmetal while supporting the the other side with
polyurethane. See http://www.bonnydoonengineering.com/ for an
explanation of this process.
ERS
<moomesa@INVALIDfnbnet.net> wrote:
>The words "Jeep" on the side of Jeep CJs is embossed with the letters
>painted on top. Actually the raised surface is more like Joop with the
>'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
>toying with the idea of adding the word "Deere" below the word "Jeep",
>on raised sheetmetal like the original. I suppose it would look like
>"Dooro" then the letters would go on top.
>
>I considered bondo, but I don't think it would work at that thickness. I
>might be able to do it in lead and I even considered doing it with a
>body hammer, carefully. I have the skills, but I'm afraid that I might
>get the sheetmetal too thin after I sand & grind.
>
>Any ideas or suggestions?
Along with the sand bag and pitch suggestions I would add that a shot
bag might be better. The shot bag is a leather bag filled with lead
shot. The bag is made of three pieces. Two discs and a strip of
leather. The discs are sewn to the strip to make a round bag with
straight sides. But what may work better is to cut letters out of
sheet that is as thick as the depression is deep. The letters should
have the edges radiused on one side. Then, press the letters into the
back side of the sheetmetal while supporting the the other side with
polyurethane. See http://www.bonnydoonengineering.com/ for an
explanation of this process.
ERS
#34
Guest
Posts: n/a
Re: Sheet metal & Jeep question
On Sat, 15 Jan 2005 11:29:50 -0600, Jeepers
<moomesa@INVALIDfnbnet.net> wrote:
>The words "Jeep" on the side of Jeep CJs is embossed with the letters
>painted on top. Actually the raised surface is more like Joop with the
>'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
>toying with the idea of adding the word "Deere" below the word "Jeep",
>on raised sheetmetal like the original. I suppose it would look like
>"Dooro" then the letters would go on top.
>
>I considered bondo, but I don't think it would work at that thickness. I
>might be able to do it in lead and I even considered doing it with a
>body hammer, carefully. I have the skills, but I'm afraid that I might
>get the sheetmetal too thin after I sand & grind.
>
>Any ideas or suggestions?
Along with the sand bag and pitch suggestions I would add that a shot
bag might be better. The shot bag is a leather bag filled with lead
shot. The bag is made of three pieces. Two discs and a strip of
leather. The discs are sewn to the strip to make a round bag with
straight sides. But what may work better is to cut letters out of
sheet that is as thick as the depression is deep. The letters should
have the edges radiused on one side. Then, press the letters into the
back side of the sheetmetal while supporting the the other side with
polyurethane. See http://www.bonnydoonengineering.com/ for an
explanation of this process.
ERS
<moomesa@INVALIDfnbnet.net> wrote:
>The words "Jeep" on the side of Jeep CJs is embossed with the letters
>painted on top. Actually the raised surface is more like Joop with the
>'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
>toying with the idea of adding the word "Deere" below the word "Jeep",
>on raised sheetmetal like the original. I suppose it would look like
>"Dooro" then the letters would go on top.
>
>I considered bondo, but I don't think it would work at that thickness. I
>might be able to do it in lead and I even considered doing it with a
>body hammer, carefully. I have the skills, but I'm afraid that I might
>get the sheetmetal too thin after I sand & grind.
>
>Any ideas or suggestions?
Along with the sand bag and pitch suggestions I would add that a shot
bag might be better. The shot bag is a leather bag filled with lead
shot. The bag is made of three pieces. Two discs and a strip of
leather. The discs are sewn to the strip to make a round bag with
straight sides. But what may work better is to cut letters out of
sheet that is as thick as the depression is deep. The letters should
have the edges radiused on one side. Then, press the letters into the
back side of the sheetmetal while supporting the the other side with
polyurethane. See http://www.bonnydoonengineering.com/ for an
explanation of this process.
ERS
#35
Guest
Posts: n/a
Re: Sheet metal & Jeep question
Jeepers proclaimed:
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
Do you have any local hobby groups that could help you with light
metal casting? Is quite easy to do with just the heat available
from a stove or barbeque. Can be done into sand or lost wax style
mold.
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
Do you have any local hobby groups that could help you with light
metal casting? Is quite easy to do with just the heat available
from a stove or barbeque. Can be done into sand or lost wax style
mold.
#36
Guest
Posts: n/a
Re: Sheet metal & Jeep question
Jeepers proclaimed:
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
Do you have any local hobby groups that could help you with light
metal casting? Is quite easy to do with just the heat available
from a stove or barbeque. Can be done into sand or lost wax style
mold.
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
Do you have any local hobby groups that could help you with light
metal casting? Is quite easy to do with just the heat available
from a stove or barbeque. Can be done into sand or lost wax style
mold.
#37
Guest
Posts: n/a
Re: Sheet metal & Jeep question
Jeepers proclaimed:
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
Do you have any local hobby groups that could help you with light
metal casting? Is quite easy to do with just the heat available
from a stove or barbeque. Can be done into sand or lost wax style
mold.
> The words "Jeep" on the side of Jeep CJs is embossed with the letters
> painted on top. Actually the raised surface is more like Joop with the
> 'e's put on. My Jeep project CJ-7 is "Jeep Deere", Green & Yellow. I was
> toying with the idea of adding the word "Deere" below the word "Jeep",
> on raised sheetmetal like the original. I suppose it would look like
> "Dooro" then the letters would go on top.
>
> I considered bondo, but I don't think it would work at that thickness. I
> might be able to do it in lead and I even considered doing it with a
> body hammer, carefully. I have the skills, but I'm afraid that I might
> get the sheetmetal too thin after I sand & grind.
>
> Any ideas or suggestions?
>
>
Do you have any local hobby groups that could help you with light
metal casting? Is quite easy to do with just the heat available
from a stove or barbeque. Can be done into sand or lost wax style
mold.
#38
Guest
Posts: n/a
Re: Sheet metal & Jeep question
In article <41E9984F.15E51CCC@***.net>,
L.W.(ßill) ------ III <----------@***.net> wrote:
> I think it needs the "John" part of Deere also.
Thanks, but it's part Jeep, part Deere, Jeep Deere.
--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.
L.W.(ßill) ------ III <----------@***.net> wrote:
> I think it needs the "John" part of Deere also.
Thanks, but it's part Jeep, part Deere, Jeep Deere.
--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.
#39
Guest
Posts: n/a
Re: Sheet metal & Jeep question
In article <41E9984F.15E51CCC@***.net>,
L.W.(ßill) ------ III <----------@***.net> wrote:
> I think it needs the "John" part of Deere also.
Thanks, but it's part Jeep, part Deere, Jeep Deere.
--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.
L.W.(ßill) ------ III <----------@***.net> wrote:
> I think it needs the "John" part of Deere also.
Thanks, but it's part Jeep, part Deere, Jeep Deere.
--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.
#40
Guest
Posts: n/a
Re: Sheet metal & Jeep question
In article <41E9984F.15E51CCC@***.net>,
L.W.(ßill) ------ III <----------@***.net> wrote:
> I think it needs the "John" part of Deere also.
Thanks, but it's part Jeep, part Deere, Jeep Deere.
--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.
L.W.(ßill) ------ III <----------@***.net> wrote:
> I think it needs the "John" part of Deere also.
Thanks, but it's part Jeep, part Deere, Jeep Deere.
--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.