replace wheel bearing Jeep TJ 2000?
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
Your bad, my bad. The OP said REAR wheel bearing.
jbjeep wrote:
> If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> sure if I have my measurement wrong someone will correct me quickly.
> -jenn
>
>
>
> On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8890@gmail.com> wrote:
>
>>> Hi Folks,
>>>
>>> Now that I just completed replacement of a water pump and thermostate,
>>> it appears my rear passanger wheel bearing might be going. I'm
>>> experiencing a squeaking sound after a bit of driving. It doesn't
>>> sound like the rear brakes. It's a metal against metal "screeching"
>>> sound, therefore I suspect a bearing.
>>>
>>> The jeep has about 145k miles on it and no bearings have been
>>> replaced.
>>>
>>> Has anyone completed this procedure? Any suggestions for completing
>>> the job?
>>>
>>> Thanks alot,
>>> Nick
jbjeep wrote:
> If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> sure if I have my measurement wrong someone will correct me quickly.
> -jenn
>
>
>
> On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8890@gmail.com> wrote:
>
>>> Hi Folks,
>>>
>>> Now that I just completed replacement of a water pump and thermostate,
>>> it appears my rear passanger wheel bearing might be going. I'm
>>> experiencing a squeaking sound after a bit of driving. It doesn't
>>> sound like the rear brakes. It's a metal against metal "screeching"
>>> sound, therefore I suspect a bearing.
>>>
>>> The jeep has about 145k miles on it and no bearings have been
>>> replaced.
>>>
>>> Has anyone completed this procedure? Any suggestions for completing
>>> the job?
>>>
>>> Thanks alot,
>>> Nick
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
In article <1186423537.139304.115170@j4g2000prf.googlegroups. com>,
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
In article <1186423537.139304.115170@j4g2000prf.googlegroups. com>,
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
In article <1186423537.139304.115170@j4g2000prf.googlegroups. com>,
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
In article <1186423537.139304.115170@j4g2000prf.googlegroups. com>,
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Nick ------ <nixon8890@gmail.com> wrote:
#Hi Folks,
#
#Now that I just completed replacement of a water pump and thermostate,
#it appears my rear passanger wheel bearing might be going. I'm
#experiencing a squeaking sound after a bit of driving. It doesn't
#sound like the rear brakes. It's a metal against metal "screeching"
#sound, therefore I suspect a bearing.
#
#The jeep has about 145k miles on it and no bearings have been
#replaced.
#
#Has anyone completed this procedure? Any suggestions for completing
#the job?
#
#Thanks alot,
#Nick
What do you have for your rear diff? Dana 35c? Dana 44?
The D35c:
http://www.stu-offroad.com/axle/d35/d35-1.htm
(the c is for custom, not c-clip)
The D44:
http://www.stu-offroad.com/axle/d44/d44-1.htm
I used a 12-ton shop press. Looking back, I should have gotten a 20-ton
press. Then I could have done the "Special Service Tool" trick.
And if you don't like cutting with a drill and dremel, make a "Special
Service Tool" for your press:
http://www.4x4wire.com/toyota/mainte...wheel_bearing/
I strongly suggest that you replace the seals along with the bearings
since you have it out already. Also, I would pack the new bearing
with some grease since it may take some time for diff lube to make
it to the bearing.
Someone recommended using RTV rubber around the edge of the oil seal.
Dunno if it would help or hurt or not.
Lastly, are you sure it is the bearing? It's a lot of work just to
find out you still have the noise when you are done!
Good luck!
/herb
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
I used an impact wrench. It's a lot easier because otherwise you just
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
I used an impact wrench. It's a lot easier because otherwise you just
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
I used an impact wrench. It's a lot easier because otherwise you just
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
I used an impact wrench. It's a lot easier because otherwise you just
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
end up spinning the whole shaft with a breaker bar. I suppose on the
rear you could set the e-brake though.
On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
> Thanks. Did you need an impact wrench to get the nut free or just use
> a breaker? I have a 1/2" impact wrench and not sure if I should get
> eh 36mm socket for it.
>
> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>
> > 36mm is correct, at least on the front hub. Just did mine last week. I
> > rented it for free from Advance Auto Parts.
>
> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>
> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
> > > sure if I have my measurement wrong someone will correct me quickly.
> > > -jenn
>
> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
> > > >>Hi Folks,
>
> > > >>Now that I just completed replacement of a water pump and thermostate,
> > > >>it appears my rear passanger wheel bearing might be going. I'm
> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
> > > >>sound like the rear brakes. It's a metal against metal "screeching"
> > > >>sound, therefore I suspect a bearing.
>
> > > >>The jeep has about 145k miles on it and no bearings have been
> > > >>replaced.
>
> > > >>Has anyone completed this procedure? Any suggestions for completing
> > > >>the job?
>
> > > >>Thanks alot,
> > > >>Nick
Guest
Posts: n/a
Re: replace wheel bearing Jeep TJ 2000?
I used a breaker bar, while the wheel was on the ground, and
had no trouble at all.
On 2007-08-08, 97tjMike <MichaelJunior@gmail.com> wrote:
> I used an impact wrench. It's a lot easier because otherwise you just
> end up spinning the whole shaft with a breaker bar. I suppose on the
> rear you could set the e-brake though.
>
>
> On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
>> Thanks. Did you need an impact wrench to get the nut free or just use
>> a breaker? I have a 1/2" impact wrench and not sure if I should get
>> eh 36mm socket for it.
>>
>> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>>
>> > 36mm is correct, at least on the front hub. Just did mine last week. I
>> > rented it for free from Advance Auto Parts.
>>
>> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>>
>> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
>> > > sure if I have my measurement wrong someone will correct me quickly.
>> > > -jenn
>>
>> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
>> > > >>Hi Folks,
>>
>> > > >>Now that I just completed replacement of a water pump and thermostate,
>> > > >>it appears my rear passanger wheel bearing might be going. I'm
>> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
>> > > >>sound like the rear brakes. It's a metal against metal "screeching"
>> > > >>sound, therefore I suspect a bearing.
>>
>> > > >>The jeep has about 145k miles on it and no bearings have been
>> > > >>replaced.
>>
>> > > >>Has anyone completed this procedure? Any suggestions for completing
>> > > >>the job?
>>
>> > > >>Thanks alot,
>> > > >>Nick
>
>
had no trouble at all.
On 2007-08-08, 97tjMike <MichaelJunior@gmail.com> wrote:
> I used an impact wrench. It's a lot easier because otherwise you just
> end up spinning the whole shaft with a breaker bar. I suppose on the
> rear you could set the e-brake though.
>
>
> On Aug 7, 5:56 pm, Nick ------ <nixon8...@gmail.com> wrote:
>> Thanks. Did you need an impact wrench to get the nut free or just use
>> a breaker? I have a 1/2" impact wrench and not sure if I should get
>> eh 36mm socket for it.
>>
>> On Aug 7, 3:07 pm, 97tjMike <MichaelJun...@gmail.com> wrote:
>>
>> > 36mm is correct, at least on the front hub. Just did mine last week. I
>> > rented it for free from Advance Auto Parts.
>>
>> > On Aug 6, 9:03 pm, jbjeep <jbj...@saw.net> wrote:
>>
>> > > If I recall correctly, you will need a 36mm socket for the "center hub nut". I am
>> > > sure if I have my measurement wrong someone will correct me quickly.
>> > > -jenn
>>
>> > > On Mon, 06 Aug 2007 18:05:37 -0000, Nick ------ <nixon8...@gmail.com> wrote:
>> > > >>Hi Folks,
>>
>> > > >>Now that I just completed replacement of a water pump and thermostate,
>> > > >>it appears my rear passanger wheel bearing might be going. I'm
>> > > >>experiencing a squeaking sound after a bit of driving. It doesn't
>> > > >>sound like the rear brakes. It's a metal against metal "screeching"
>> > > >>sound, therefore I suspect a bearing.
>>
>> > > >>The jeep has about 145k miles on it and no bearings have been
>> > > >>replaced.
>>
>> > > >>Has anyone completed this procedure? Any suggestions for completing
>> > > >>the job?
>>
>> > > >>Thanks alot,
>> > > >>Nick
>
>