power windows control assembly
07-25-2006, 01:36 PM
#1
Guest
Posts: n/a
power windows control assembly
I need HELP!!
My 2000 cherokee limited has a problem in the drivers armrest control
assembly.
My Haynes manual states that I should "pry out" the assembly and unplug
it.
I have tried this and cannot seem to get the assembly all the way out.
Can you help me on this??
Thank-you
Jim
My 2000 cherokee limited has a problem in the drivers armrest control
assembly.
My Haynes manual states that I should "pry out" the assembly and unplug
it.
I have tried this and cannot seem to get the assembly all the way out.
Can you help me on this??
Thank-you
Jim
07-25-2006, 03:01 PM
#2
Guest
Posts: n/a
Re: power windows control assembly
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
07-25-2006, 03:01 PM
#3
Guest
Posts: n/a
Re: power windows control assembly
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
07-25-2006, 03:01 PM
#4
Guest
Posts: n/a
Re: power windows control assembly
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
07-25-2006, 03:01 PM
#5
Guest
Posts: n/a
Re: power windows control assembly
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim panel from the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - REMOVAL).
(3) Disconnect the door wire harness connectors
from the door module connector receptacles.
(4) Remove the three screws that secure the door
module to the front door trim panel (Fig. 8).
(5) Remove the door module from the front door
trim panel.
INSTALLATION
(1) Position the door module onto the front door
trim panel.
(2) Install and tighten the three screws that secure
the door module to the front door trim panel. Tighten
the screws to 2.2 N·m (20 in. lbs.).
(3) Reconnect the door wire harness connectors to
the door module connector receptacles.
(4) Reinstall the trim panel onto the front door
inner panel. (Refer to 23 - BODY/DOOR - FRONT/
TRIM PANEL - INSTALLATION).
(5) Reconnect the battery negative cable.
"jim" <piglet80917@netscape.net> wrote in message
news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
>I need HELP!!
> My 2000 cherokee limited has a problem in the drivers armrest control
> assembly.
> My Haynes manual states that I should "pry out" the assembly and unplug
> it.
> I have tried this and cannot seem to get the assembly all the way out.
> Can you help me on this??
> Thank-you
> Jim
>
07-31-2006, 11:50 AM
#6
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
07-31-2006, 11:50 AM
#7
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
07-31-2006, 11:50 AM
#8
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
07-31-2006, 11:50 AM
#9
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
07-31-2006, 11:54 AM
#10
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
Thank-you Billy Ray..
It worked great!!
Do I need the whole assembly for the lock-out switch malfunction??
Would a bypass work??
Does anyone know a good deal on a new assembly??
Thank-you again!!
Jim
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
