Re: PING ßill Hughes --- Adjustment tool for Quadrajet
 

Thats it. Thanks

In article <9nout0dku0u7j1o5uleai692ks0gt9ivrv@4ax.com>, bllsht
<nospam@invaliddot.net> wrote:

> In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>
> >Am looking for the tool used to adjust the main metering rod on a
> >Rochester 2SE carburator .... the tool that you use to change the
> >mixture while the carb is ON the engine. Would probably be the same
> >tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> >animal? Use to be available for about $30 .. about 20 years ago.
>
> Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
> the E2SE, and if my memory is correct, the 2SE also.
>
> http://buy1.snapon.com/catalog/item....6&PartNo=S6136
> A&group_id=1441&supersede=&store=snapon-store&tool=all
>
>
> Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
> http://buy1.snapon.com/catalog/item....&group_ID=1441
> Looks like you can only get this one as part of 2005ACS shown here:
> http://buy1.snapon.com/catalog/item....&group_ID=1441
>
>
>

Re: PING ßill Hughes --- Adjustment tool for Quadrajet
 

Thats it. Thanks

In article <9nout0dku0u7j1o5uleai692ks0gt9ivrv@4ax.com>, bllsht
<nospam@invaliddot.net> wrote:

> In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>
> >Am looking for the tool used to adjust the main metering rod on a
> >Rochester 2SE carburator .... the tool that you use to change the
> >mixture while the carb is ON the engine. Would probably be the same
> >tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> >animal? Use to be available for about $30 .. about 20 years ago.
>
> Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
> the E2SE, and if my memory is correct, the 2SE also.
>
> http://buy1.snapon.com/catalog/item....6&PartNo=S6136
> A&group_id=1441&supersede=&store=snapon-store&tool=all
>
>
> Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
> http://buy1.snapon.com/catalog/item....&group_ID=1441
> Looks like you can only get this one as part of 2005ACS shown here:
> http://buy1.snapon.com/catalog/item....&group_ID=1441
>
>
>

Re: PING ßill Hughes --- Adjustment tool for Quadrajet
 

Thats it. Thanks

In article <9nout0dku0u7j1o5uleai692ks0gt9ivrv@4ax.com>, bllsht
<nospam@invaliddot.net> wrote:

> In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>
> >Am looking for the tool used to adjust the main metering rod on a
> >Rochester 2SE carburator .... the tool that you use to change the
> >mixture while the carb is ON the engine. Would probably be the same
> >tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> >animal? Use to be available for about $30 .. about 20 years ago.
>
> Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
> the E2SE, and if my memory is correct, the 2SE also.
>
> http://buy1.snapon.com/catalog/item....6&PartNo=S6136
> A&group_id=1441&supersede=&store=snapon-store&tool=all
>
>
> Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
> http://buy1.snapon.com/catalog/item....&group_ID=1441
> Looks like you can only get this one as part of 2005ACS shown here:
> http://buy1.snapon.com/catalog/item....&group_ID=1441
>
>
>