PING ßill ------ --- Adjustment tool for Quadrajet
Guest
Posts: n/a
PING ßill ------ --- Adjustment tool for Quadrajet
Am looking for the tool used to adjust the main metering rod on a
Rochester 2SE carburator .... the tool that you use to change the
mixture while the carb is ON the engine. Would probably be the same
tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
animal? Use to be available for about $30 .. about 20 years ago.
Rochester 2SE carburator .... the tool that you use to change the
mixture while the carb is ON the engine. Would probably be the same
tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
animal? Use to be available for about $30 .. about 20 years ago.
Guest
Posts: n/a
Re: PING =?iso-8859-1?Q?=DFill?= ------ --- Adjustment tool forQuadrajet
Hi Rich,
Rochester 2SE: http://www.carburetorfactory.com/expvw24.html I
don't know of a special tool for the metering rods, we just changed them
from their outside plate on the old AFBs, to richen them for the drag
strip. As far as I know no one bothered with the Quadrajet, it was made
for Kalifornia's SMOG cars with it's puny primaries, float bowl, and
problematic needle valve, what a POS: valve.
http://www.carburetorfactory.com/expvw27.html Other than it made me lots
of money rebuilding them as stuff would bypass the spring loaded fuel
filter, and jam the valve open.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rich Hampel wrote:
>
> Am looking for the tool used to adjust the main metering rod on a
> Rochester 2SE carburator .... the tool that you use to change the
> mixture while the carb is ON the engine. Would probably be the same
> tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> animal? Use to be available for about $30 .. about 20 years ago.
Rochester 2SE: http://www.carburetorfactory.com/expvw24.html I
don't know of a special tool for the metering rods, we just changed them
from their outside plate on the old AFBs, to richen them for the drag
strip. As far as I know no one bothered with the Quadrajet, it was made
for Kalifornia's SMOG cars with it's puny primaries, float bowl, and
problematic needle valve, what a POS: valve.
http://www.carburetorfactory.com/expvw27.html Other than it made me lots
of money rebuilding them as stuff would bypass the spring loaded fuel
filter, and jam the valve open.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rich Hampel wrote:
>
> Am looking for the tool used to adjust the main metering rod on a
> Rochester 2SE carburator .... the tool that you use to change the
> mixture while the carb is ON the engine. Would probably be the same
> tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> animal? Use to be available for about $30 .. about 20 years ago.
Guest
Posts: n/a
Re: PING =?iso-8859-1?Q?=DFill?= ------ --- Adjustment tool forQuadrajet
Hi Rich,
Rochester 2SE: http://www.carburetorfactory.com/expvw24.html I
don't know of a special tool for the metering rods, we just changed them
from their outside plate on the old AFBs, to richen them for the drag
strip. As far as I know no one bothered with the Quadrajet, it was made
for Kalifornia's SMOG cars with it's puny primaries, float bowl, and
problematic needle valve, what a POS: valve.
http://www.carburetorfactory.com/expvw27.html Other than it made me lots
of money rebuilding them as stuff would bypass the spring loaded fuel
filter, and jam the valve open.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rich Hampel wrote:
>
> Am looking for the tool used to adjust the main metering rod on a
> Rochester 2SE carburator .... the tool that you use to change the
> mixture while the carb is ON the engine. Would probably be the same
> tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> animal? Use to be available for about $30 .. about 20 years ago.
Rochester 2SE: http://www.carburetorfactory.com/expvw24.html I
don't know of a special tool for the metering rods, we just changed them
from their outside plate on the old AFBs, to richen them for the drag
strip. As far as I know no one bothered with the Quadrajet, it was made
for Kalifornia's SMOG cars with it's puny primaries, float bowl, and
problematic needle valve, what a POS: valve.
http://www.carburetorfactory.com/expvw27.html Other than it made me lots
of money rebuilding them as stuff would bypass the spring loaded fuel
filter, and jam the valve open.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rich Hampel wrote:
>
> Am looking for the tool used to adjust the main metering rod on a
> Rochester 2SE carburator .... the tool that you use to change the
> mixture while the carb is ON the engine. Would probably be the same
> tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> animal? Use to be available for about $30 .. about 20 years ago.
Guest
Posts: n/a
Re: PING =?iso-8859-1?Q?=DFill?= ------ --- Adjustment tool forQuadrajet
Hi Rich,
Rochester 2SE: http://www.carburetorfactory.com/expvw24.html I
don't know of a special tool for the metering rods, we just changed them
from their outside plate on the old AFBs, to richen them for the drag
strip. As far as I know no one bothered with the Quadrajet, it was made
for Kalifornia's SMOG cars with it's puny primaries, float bowl, and
problematic needle valve, what a POS: valve.
http://www.carburetorfactory.com/expvw27.html Other than it made me lots
of money rebuilding them as stuff would bypass the spring loaded fuel
filter, and jam the valve open.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rich Hampel wrote:
>
> Am looking for the tool used to adjust the main metering rod on a
> Rochester 2SE carburator .... the tool that you use to change the
> mixture while the carb is ON the engine. Would probably be the same
> tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> animal? Use to be available for about $30 .. about 20 years ago.
Rochester 2SE: http://www.carburetorfactory.com/expvw24.html I
don't know of a special tool for the metering rods, we just changed them
from their outside plate on the old AFBs, to richen them for the drag
strip. As far as I know no one bothered with the Quadrajet, it was made
for Kalifornia's SMOG cars with it's puny primaries, float bowl, and
problematic needle valve, what a POS: valve.
http://www.carburetorfactory.com/expvw27.html Other than it made me lots
of money rebuilding them as stuff would bypass the spring loaded fuel
filter, and jam the valve open.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rich Hampel wrote:
>
> Am looking for the tool used to adjust the main metering rod on a
> Rochester 2SE carburator .... the tool that you use to change the
> mixture while the carb is ON the engine. Would probably be the same
> tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
> animal? Use to be available for about $30 .. about 20 years ago.
Guest
Posts: n/a
Re: PING ßill ------ --- Adjustment tool for Quadrajet
In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Being in California, I rarely worked on the 2SE, but I believe it's the same
tool for the E2SE. Snap-On made the tool I have. Will have to check the number
on it tomorrow.
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Being in California, I rarely worked on the 2SE, but I believe it's the same
tool for the E2SE. Snap-On made the tool I have. Will have to check the number
on it tomorrow.
Guest
Posts: n/a
Re: PING ßill ------ --- Adjustment tool for Quadrajet
In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Being in California, I rarely worked on the 2SE, but I believe it's the same
tool for the E2SE. Snap-On made the tool I have. Will have to check the number
on it tomorrow.
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Being in California, I rarely worked on the 2SE, but I believe it's the same
tool for the E2SE. Snap-On made the tool I have. Will have to check the number
on it tomorrow.
Guest
Posts: n/a
Re: PING ßill ------ --- Adjustment tool for Quadrajet
In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Being in California, I rarely worked on the 2SE, but I believe it's the same
tool for the E2SE. Snap-On made the tool I have. Will have to check the number
on it tomorrow.
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Being in California, I rarely worked on the 2SE, but I believe it's the same
tool for the E2SE. Snap-On made the tool I have. Will have to check the number
on it tomorrow.
Guest
Posts: n/a
Re: PING ßill ------ --- Adjustment tool for Quadrajet
In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
the E2SE, and if my memory is correct, the 2SE also.
http://buy1.snapon.com/catalog/item....store&tool=all
Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
http://buy1.snapon.com/catalog/item....&group_ID=1441
Looks like you can only get this one as part of 2005ACS shown here:
http://buy1.snapon.com/catalog/item....&group_ID=1441
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
the E2SE, and if my memory is correct, the 2SE also.
http://buy1.snapon.com/catalog/item....store&tool=all
Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
http://buy1.snapon.com/catalog/item....&group_ID=1441
Looks like you can only get this one as part of 2005ACS shown here:
http://buy1.snapon.com/catalog/item....&group_ID=1441
Guest
Posts: n/a
Re: PING ßill ------ --- Adjustment tool for Quadrajet
In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
the E2SE, and if my memory is correct, the 2SE also.
http://buy1.snapon.com/catalog/item....store&tool=all
Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
http://buy1.snapon.com/catalog/item....&group_ID=1441
Looks like you can only get this one as part of 2005ACS shown here:
http://buy1.snapon.com/catalog/item....&group_ID=1441
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
the E2SE, and if my memory is correct, the 2SE also.
http://buy1.snapon.com/catalog/item....store&tool=all
Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
http://buy1.snapon.com/catalog/item....&group_ID=1441
Looks like you can only get this one as part of 2005ACS shown here:
http://buy1.snapon.com/catalog/item....&group_ID=1441
Guest
Posts: n/a
Re: PING ßill ------ --- Adjustment tool for Quadrajet
In message <060120052229022072%RhmpL33@nospam.net>, "Rich Hampel" wrote:
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
the E2SE, and if my memory is correct, the 2SE also.
http://buy1.snapon.com/catalog/item....store&tool=all
Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
http://buy1.snapon.com/catalog/item....&group_ID=1441
Looks like you can only get this one as part of 2005ACS shown here:
http://buy1.snapon.com/catalog/item....&group_ID=1441
>Am looking for the tool used to adjust the main metering rod on a
>Rochester 2SE carburator .... the tool that you use to change the
>mixture while the carb is ON the engine. Would probably be the same
>tool used on a Q-jet. Any ideas of where I can locate/purchase sucn an
>animal? Use to be available for about $30 .. about 20 years ago.
Snap-On S6136A. 2.5mm double "D" available online for $17. This was used on
the E2SE, and if my memory is correct, the 2SE also.
http://buy1.snapon.com/catalog/item....store&tool=all
Snap-On S6135A. 2.5mm hex. I have this but don't recall using it.
http://buy1.snapon.com/catalog/item....&group_ID=1441
Looks like you can only get this one as part of 2005ACS shown here:
http://buy1.snapon.com/catalog/item....&group_ID=1441