|
Pics or Call out of Power Steering bracket assembly w/ MPI
Hi all,
I need pics or a call-out of the power steering bracket assembly for a Serp Belt on a 258. Can any one take a pic or several pics of theirs at different angles and send it to me? Or point to some on the web. Or send me or point me to a call-out of that area. Mine doesn't seem to be going together as I "think" it should. thanks, Bill |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
bill-don't know if you've seen this site. this guy's pretty cool and his
projects page simply rocks! good luck! http://www.sierrajeep.com/moparmpi.htm "William Oliveri" <wuji@bigvalley.net> wrote in message news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > Hi all, > I made some pics with my crappy digital camera so here goes: > > This one shows the back bracket (attached to the engine with 2 bolts at the > bottom). I had to add a couple of washers between the bracket and the > engine to push it out. Otherwise the bracket hole didn't line up with the > bolt hole on the intake manifold. > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > I re-evaluated the intake manifold and see that is seated perfectly along > with the exhaust manifold. > I'm sure it's centered correctly because I left the two center bolt holes > alone when grinding out the others to make it fit. > > This is a frontal view where you can see the left side of the diamond > bracket doesn't line up with the hole at the water pump and the other > bracket which is attached to the head bolts on top. > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > These are other versions of #1 > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > Thanks for any comments, suggestions. > > bill > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > Hi all, > > > > I need pics or a call-out of the power steering bracket assembly for a > > Serp Belt on a 258. Can any one take a pic or several pics of theirs at > > different angles and send it to me? Or point to some on the web. Or send > > me or point me to a call-out of that area. > > > > Mine doesn't seem to be going together as I "think" it should. > > > > thanks, > > > > Bill > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
bill-don't know if you've seen this site. this guy's pretty cool and his
projects page simply rocks! good luck! http://www.sierrajeep.com/moparmpi.htm "William Oliveri" <wuji@bigvalley.net> wrote in message news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > Hi all, > I made some pics with my crappy digital camera so here goes: > > This one shows the back bracket (attached to the engine with 2 bolts at the > bottom). I had to add a couple of washers between the bracket and the > engine to push it out. Otherwise the bracket hole didn't line up with the > bolt hole on the intake manifold. > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > I re-evaluated the intake manifold and see that is seated perfectly along > with the exhaust manifold. > I'm sure it's centered correctly because I left the two center bolt holes > alone when grinding out the others to make it fit. > > This is a frontal view where you can see the left side of the diamond > bracket doesn't line up with the hole at the water pump and the other > bracket which is attached to the head bolts on top. > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > These are other versions of #1 > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > Thanks for any comments, suggestions. > > bill > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > Hi all, > > > > I need pics or a call-out of the power steering bracket assembly for a > > Serp Belt on a 258. Can any one take a pic or several pics of theirs at > > different angles and send it to me? Or point to some on the web. Or send > > me or point me to a call-out of that area. > > > > Mine doesn't seem to be going together as I "think" it should. > > > > thanks, > > > > Bill > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
Hey thanks Serg. Yes, I have this guy's page along with another and a host
of pics downloaded to my pc. I just don't have a good pic of the finished bracket assembly of the power steering pump on a serp belt. I basicly have been told just to make it work. No prob. I'll work it out. Thanks for the reply. bill "serg" <none@none.com> wrote in message news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > bill-don't know if you've seen this site. this guy's pretty cool and his > projects page simply rocks! good luck! > > http://www.sierrajeep.com/moparmpi.htm > > "William Oliveri" <wuji@bigvalley.net> wrote in message > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > Hi all, > > I made some pics with my crappy digital camera so here goes: > > > > This one shows the back bracket (attached to the engine with 2 bolts at > the > > bottom). I had to add a couple of washers between the bracket and the > > engine to push it out. Otherwise the bracket hole didn't line up with the > > bolt hole on the intake manifold. > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > I re-evaluated the intake manifold and see that is seated perfectly along > > with the exhaust manifold. > > I'm sure it's centered correctly because I left the two center bolt holes > > alone when grinding out the others to make it fit. > > > > This is a frontal view where you can see the left side of the diamond > > bracket doesn't line up with the hole at the water pump and the other > > bracket which is attached to the head bolts on top. > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > These are other versions of #1 > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > Thanks for any comments, suggestions. > > > > bill > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > Hi all, > > > > > > I need pics or a call-out of the power steering bracket assembly for a > > > Serp Belt on a 258. Can any one take a pic or several pics of theirs at > > > different angles and send it to me? Or point to some on the web. Or > send > > > me or point me to a call-out of that area. > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > thanks, > > > > > > Bill > > > > > > > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
Hey thanks Serg. Yes, I have this guy's page along with another and a host
of pics downloaded to my pc. I just don't have a good pic of the finished bracket assembly of the power steering pump on a serp belt. I basicly have been told just to make it work. No prob. I'll work it out. Thanks for the reply. bill "serg" <none@none.com> wrote in message news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > bill-don't know if you've seen this site. this guy's pretty cool and his > projects page simply rocks! good luck! > > http://www.sierrajeep.com/moparmpi.htm > > "William Oliveri" <wuji@bigvalley.net> wrote in message > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > Hi all, > > I made some pics with my crappy digital camera so here goes: > > > > This one shows the back bracket (attached to the engine with 2 bolts at > the > > bottom). I had to add a couple of washers between the bracket and the > > engine to push it out. Otherwise the bracket hole didn't line up with the > > bolt hole on the intake manifold. > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > I re-evaluated the intake manifold and see that is seated perfectly along > > with the exhaust manifold. > > I'm sure it's centered correctly because I left the two center bolt holes > > alone when grinding out the others to make it fit. > > > > This is a frontal view where you can see the left side of the diamond > > bracket doesn't line up with the hole at the water pump and the other > > bracket which is attached to the head bolts on top. > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > These are other versions of #1 > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > Thanks for any comments, suggestions. > > > > bill > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > Hi all, > > > > > > I need pics or a call-out of the power steering bracket assembly for a > > > Serp Belt on a 258. Can any one take a pic or several pics of theirs at > > > different angles and send it to me? Or point to some on the web. Or > send > > > me or point me to a call-out of that area. > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > thanks, > > > > > > Bill > > > > > > > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
I would jump in here, but I have a vbelt system, and I don't know that the
brackets are the same or different. My power steering pump gets a bracket on the front and on the back. I'll have to look at it more closely to be sure, but my recollection is that there are two brackets that sandwich the body of the pump. I actually think that only one of the brackets holds the pump on, the other is itself a bracket that held the air pump for the cold air injectors (part of the old smog system). I'll take a second look ant my power steering and describe the brackets. I seem to remember having to put in a couple of washers, and I seem to remember there was a spacer of about an inch or inch and a half that was needed too. "William Oliveri" <wuji@bigvalley.net> wrote in message news:biet1f$8fm3m$1@ID-193866.news.uni-berlin.de... > Hey thanks Serg. Yes, I have this guy's page along with another and a host > of pics downloaded to my pc. I just don't have a good pic of the finished > bracket assembly of the power steering pump on a serp belt. I basicly have > been told just to make it work. > > No prob. I'll work it out. > > Thanks for the reply. > > bill > > > "serg" <none@none.com> wrote in message > news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > > bill-don't know if you've seen this site. this guy's pretty cool and his > > projects page simply rocks! good luck! > > > > http://www.sierrajeep.com/moparmpi.htm > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > > Hi all, > > > I made some pics with my crappy digital camera so here goes: > > > > > > This one shows the back bracket (attached to the engine with 2 bolts at > > the > > > bottom). I had to add a couple of washers between the bracket and the > > > engine to push it out. Otherwise the bracket hole didn't line up with > the > > > bolt hole on the intake manifold. > > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > > > I re-evaluated the intake manifold and see that is seated perfectly > along > > > with the exhaust manifold. > > > I'm sure it's centered correctly because I left the two center bolt > holes > > > alone when grinding out the others to make it fit. > > > > > > This is a frontal view where you can see the left side of the diamond > > > bracket doesn't line up with the hole at the water pump and the other > > > bracket which is attached to the head bolts on top. > > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > > > > These are other versions of #1 > > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > > > > Thanks for any comments, suggestions. > > > > > > bill > > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > > Hi all, > > > > > > > > I need pics or a call-out of the power steering bracket assembly for > a > > > > Serp Belt on a 258. Can any one take a pic or several pics of theirs > at > > > > different angles and send it to me? Or point to some on the web. Or > > send > > > > me or point me to a call-out of that area. > > > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > > > thanks, > > > > > > > > Bill > > > > > > > > > > > > > > > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
I would jump in here, but I have a vbelt system, and I don't know that the
brackets are the same or different. My power steering pump gets a bracket on the front and on the back. I'll have to look at it more closely to be sure, but my recollection is that there are two brackets that sandwich the body of the pump. I actually think that only one of the brackets holds the pump on, the other is itself a bracket that held the air pump for the cold air injectors (part of the old smog system). I'll take a second look ant my power steering and describe the brackets. I seem to remember having to put in a couple of washers, and I seem to remember there was a spacer of about an inch or inch and a half that was needed too. "William Oliveri" <wuji@bigvalley.net> wrote in message news:biet1f$8fm3m$1@ID-193866.news.uni-berlin.de... > Hey thanks Serg. Yes, I have this guy's page along with another and a host > of pics downloaded to my pc. I just don't have a good pic of the finished > bracket assembly of the power steering pump on a serp belt. I basicly have > been told just to make it work. > > No prob. I'll work it out. > > Thanks for the reply. > > bill > > > "serg" <none@none.com> wrote in message > news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > > bill-don't know if you've seen this site. this guy's pretty cool and his > > projects page simply rocks! good luck! > > > > http://www.sierrajeep.com/moparmpi.htm > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > > Hi all, > > > I made some pics with my crappy digital camera so here goes: > > > > > > This one shows the back bracket (attached to the engine with 2 bolts at > > the > > > bottom). I had to add a couple of washers between the bracket and the > > > engine to push it out. Otherwise the bracket hole didn't line up with > the > > > bolt hole on the intake manifold. > > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > > > I re-evaluated the intake manifold and see that is seated perfectly > along > > > with the exhaust manifold. > > > I'm sure it's centered correctly because I left the two center bolt > holes > > > alone when grinding out the others to make it fit. > > > > > > This is a frontal view where you can see the left side of the diamond > > > bracket doesn't line up with the hole at the water pump and the other > > > bracket which is attached to the head bolts on top. > > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > > > > These are other versions of #1 > > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > > > > Thanks for any comments, suggestions. > > > > > > bill > > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > > Hi all, > > > > > > > > I need pics or a call-out of the power steering bracket assembly for > a > > > > Serp Belt on a 258. Can any one take a pic or several pics of theirs > at > > > > different angles and send it to me? Or point to some on the web. Or > > send > > > > me or point me to a call-out of that area. > > > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > > > thanks, > > > > > > > > Bill > > > > > > > > > > > > > > > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
same reason why i haven't sent pix either...
"Jeff Strickland" <beerman@yahoo.com> wrote in message news:<vkn69a2s2ma52c@corp.supernews.com>... > I would jump in here, but I have a vbelt system, and I don't know that the > brackets are the same or different. > > My power steering pump gets a bracket on the front and on the back. I'll > have to look at it more closely to be sure, but my recollection is that > there are two brackets that sandwich the body of the pump. I actually think > that only one of the brackets holds the pump on, the other is itself a > bracket that held the air pump for the cold air injectors (part of the old > smog system). > > I'll take a second look ant my power steering and describe the brackets. I > seem to remember having to put in a couple of washers, and I seem to > remember there was a spacer of about an inch or inch and a half that was > needed too. > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > news:biet1f$8fm3m$1@ID-193866.news.uni-berlin.de... > > Hey thanks Serg. Yes, I have this guy's page along with another and a > host > > of pics downloaded to my pc. I just don't have a good pic of the finished > > bracket assembly of the power steering pump on a serp belt. I basicly > have > > been told just to make it work. > > > > No prob. I'll work it out. > > > > Thanks for the reply. > > > > bill > > > > > > "serg" <none@none.com> wrote in message > > news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > > > bill-don't know if you've seen this site. this guy's pretty cool and > his > > > projects page simply rocks! good luck! > > > > > > http://www.sierrajeep.com/moparmpi.htm > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > > > Hi all, > > > > I made some pics with my crappy digital camera so here goes: > > > > > > > > This one shows the back bracket (attached to the engine with 2 bolts > at > the > > > > bottom). I had to add a couple of washers between the bracket and the > > > > engine to push it out. Otherwise the bracket hole didn't line up with > the > > > > bolt hole on the intake manifold. > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > > > > > I re-evaluated the intake manifold and see that is seated perfectly > along > > > > with the exhaust manifold. > > > > I'm sure it's centered correctly because I left the two center bolt > holes > > > > alone when grinding out the others to make it fit. > > > > > > > > This is a frontal view where you can see the left side of the diamond > > > > bracket doesn't line up with the hole at the water pump and the other > > > > bracket which is attached to the head bolts on top. > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > > > > > > > These are other versions of #1 > > > > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > > > > > > > Thanks for any comments, suggestions. > > > > > > > > bill > > > > > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > > > Hi all, > > > > > > > > > > I need pics or a call-out of the power steering bracket assembly > for > a > > > > > Serp Belt on a 258. Can any one take a pic or several pics of > theirs > at > > > > > different angles and send it to me? Or point to some on the web. > Or > send > > > > > me or point me to a call-out of that area. > > > > > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > > > > > thanks, > > > > > > > > > > Bill > > > > > > > > > > > > > > > > > > > > > > > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
same reason why i haven't sent pix either...
"Jeff Strickland" <beerman@yahoo.com> wrote in message news:<vkn69a2s2ma52c@corp.supernews.com>... > I would jump in here, but I have a vbelt system, and I don't know that the > brackets are the same or different. > > My power steering pump gets a bracket on the front and on the back. I'll > have to look at it more closely to be sure, but my recollection is that > there are two brackets that sandwich the body of the pump. I actually think > that only one of the brackets holds the pump on, the other is itself a > bracket that held the air pump for the cold air injectors (part of the old > smog system). > > I'll take a second look ant my power steering and describe the brackets. I > seem to remember having to put in a couple of washers, and I seem to > remember there was a spacer of about an inch or inch and a half that was > needed too. > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > news:biet1f$8fm3m$1@ID-193866.news.uni-berlin.de... > > Hey thanks Serg. Yes, I have this guy's page along with another and a > host > > of pics downloaded to my pc. I just don't have a good pic of the finished > > bracket assembly of the power steering pump on a serp belt. I basicly > have > > been told just to make it work. > > > > No prob. I'll work it out. > > > > Thanks for the reply. > > > > bill > > > > > > "serg" <none@none.com> wrote in message > > news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > > > bill-don't know if you've seen this site. this guy's pretty cool and > his > > > projects page simply rocks! good luck! > > > > > > http://www.sierrajeep.com/moparmpi.htm > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > > > Hi all, > > > > I made some pics with my crappy digital camera so here goes: > > > > > > > > This one shows the back bracket (attached to the engine with 2 bolts > at > the > > > > bottom). I had to add a couple of washers between the bracket and the > > > > engine to push it out. Otherwise the bracket hole didn't line up with > the > > > > bolt hole on the intake manifold. > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > > > > > I re-evaluated the intake manifold and see that is seated perfectly > along > > > > with the exhaust manifold. > > > > I'm sure it's centered correctly because I left the two center bolt > holes > > > > alone when grinding out the others to make it fit. > > > > > > > > This is a frontal view where you can see the left side of the diamond > > > > bracket doesn't line up with the hole at the water pump and the other > > > > bracket which is attached to the head bolts on top. > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > > > > > > > These are other versions of #1 > > > > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > > > > > > > Thanks for any comments, suggestions. > > > > > > > > bill > > > > > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > > > Hi all, > > > > > > > > > > I need pics or a call-out of the power steering bracket assembly > for > a > > > > > Serp Belt on a 258. Can any one take a pic or several pics of > theirs > at > > > > > different angles and send it to me? Or point to some on the web. > Or > send > > > > > me or point me to a call-out of that area. > > > > > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > > > > > thanks, > > > > > > > > > > Bill > > > > > > > > > > > > > > > > > > > > > > > > > > > > |
Re: Pics or Call out of Power Steering bracket assembly w/ MPI
Thanks guys, Another thing I could do is call jeepsrus to see what they to.
Thanks again, bill "serg" <sfon@yahoo.com> wrote in message news:934d0785.0308261456.14af122e@posting.google.c om... > same reason why i haven't sent pix either... > > > "Jeff Strickland" <beerman@yahoo.com> wrote in message news:<vkn69a2s2ma52c@corp.supernews.com>... > > I would jump in here, but I have a vbelt system, and I don't know that the > > brackets are the same or different. > > > > My power steering pump gets a bracket on the front and on the back. I'll > > have to look at it more closely to be sure, but my recollection is that > > there are two brackets that sandwich the body of the pump. I actually think > > that only one of the brackets holds the pump on, the other is itself a > > bracket that held the air pump for the cold air injectors (part of the old > > smog system). > > > > I'll take a second look ant my power steering and describe the brackets. I > > seem to remember having to put in a couple of washers, and I seem to > > remember there was a spacer of about an inch or inch and a half that was > > needed too. > > > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > news:biet1f$8fm3m$1@ID-193866.news.uni-berlin.de... > > > Hey thanks Serg. Yes, I have this guy's page along with another and a > > host > > > of pics downloaded to my pc. I just don't have a good pic of the finished > > > bracket assembly of the power steering pump on a serp belt. I basicly > > have > > > been told just to make it work. > > > > > > No prob. I'll work it out. > > > > > > Thanks for the reply. > > > > > > bill > > > > > > > > > "serg" <none@none.com> wrote in message > > > news:w2C2b.7198$J%4.238@newssvr25.news.prodigy.com ... > > > > bill-don't know if you've seen this site. this guy's pretty cool and > > his > > > > projects page simply rocks! good luck! > > > > > > > > http://www.sierrajeep.com/moparmpi.htm > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > > news:bibn3v$7fhd4$1@ID-193866.news.uni-berlin.de... > > > > > Hi all, > > > > > I made some pics with my crappy digital camera so here goes: > > > > > > > > > > This one shows the back bracket (attached to the engine with 2 bolts > > at > > the > > > > > bottom). I had to add a couple of washers between the bracket and the > > > > > engine to push it out. Otherwise the bracket hole didn't line up with > > the > > > > > bolt hole on the intake manifold. > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets1.jpg > > > > > > > > > > I re-evaluated the intake manifold and see that is seated perfectly > > along > > > > > with the exhaust manifold. > > > > > I'm sure it's centered correctly because I left the two center bolt > > holes > > > > > alone when grinding out the others to make it fit. > > > > > > > > > > This is a frontal view where you can see the left side of the diamond > > > > > bracket doesn't line up with the hole at the water pump and the other > > > > > bracket which is attached to the head bolts on top. > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets3.jpg > > > > > > > > > > > > > > > These are other versions of #1 > > > > > > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets2.jpg > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets4.jpg > > > > > http://members.bigvalley.net/wuji/jeep/PSbrackets5.jpg > > > > > > > > > > > > > > > Thanks for any comments, suggestions. > > > > > > > > > > bill > > > > > > > > > > > > > > > "William Oliveri" <wuji@bigvalley.net> wrote in message > > > > > news:bibhrh$7hdl6$1@ID-193866.news.uni-berlin.de... > > > > > > Hi all, > > > > > > > > > > > > I need pics or a call-out of the power steering bracket assembly > > for > > a > > > > > > Serp Belt on a 258. Can any one take a pic or several pics of > > theirs > > at > > > > > > different angles and send it to me? Or point to some on the web. > > Or > > send > > > > > > me or point me to a call-out of that area. > > > > > > > > > > > > Mine doesn't seem to be going together as I "think" it should. > > > > > > > > > > > > thanks, > > > > > > > > > > > > Bill > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > |
| All times are GMT -4. The time now is 12:57 AM. |
© 2024 MH Sub I, LLC dba Internet Brands