O2 sensor? 89 YJ
Guest
Posts: n/a
O2 sensor? 89 YJ
OK, another question. During idle the stepper motor is constantly moving
the needle in and out adjusting the mixture to the point of nearly
stalling and back again. Could this be the result of a bad O2 sensor?
Also I have a couple of vacuum ports on the carb that are not connected
to anything, one is blocked and two are open. Where can I get a
schematic of this carb (carter).
Thanks in advance, everyone here has been a tremendous help.
the needle in and out adjusting the mixture to the point of nearly
stalling and back again. Could this be the result of a bad O2 sensor?
Also I have a couple of vacuum ports on the carb that are not connected
to anything, one is blocked and two are open. Where can I get a
schematic of this carb (carter).
Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
Usually, if the O2 sensor is dead, the pins won't move. It sounds to me like
the pins are trying to compensate for a vacuum leak (open vacuum port).
I'm sure Bill will shortly post a link for the vacuum diagram, so I won't
bother looking for it for you. I know he posted one within the past month or
so.
"Poe" <Poe34@mail.com> wrote in message
news:ZgaWe.3016$6Z1.752554@news20.bellglobal.com.. .
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
the pins are trying to compensate for a vacuum leak (open vacuum port).
I'm sure Bill will shortly post a link for the vacuum diagram, so I won't
bother looking for it for you. I know he posted one within the past month or
so.
"Poe" <Poe34@mail.com> wrote in message
news:ZgaWe.3016$6Z1.752554@news20.bellglobal.com.. .
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
Usually, if the O2 sensor is dead, the pins won't move. It sounds to me like
the pins are trying to compensate for a vacuum leak (open vacuum port).
I'm sure Bill will shortly post a link for the vacuum diagram, so I won't
bother looking for it for you. I know he posted one within the past month or
so.
"Poe" <Poe34@mail.com> wrote in message
news:ZgaWe.3016$6Z1.752554@news20.bellglobal.com.. .
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
the pins are trying to compensate for a vacuum leak (open vacuum port).
I'm sure Bill will shortly post a link for the vacuum diagram, so I won't
bother looking for it for you. I know he posted one within the past month or
so.
"Poe" <Poe34@mail.com> wrote in message
news:ZgaWe.3016$6Z1.752554@news20.bellglobal.com.. .
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
Usually, if the O2 sensor is dead, the pins won't move. It sounds to me like
the pins are trying to compensate for a vacuum leak (open vacuum port).
I'm sure Bill will shortly post a link for the vacuum diagram, so I won't
bother looking for it for you. I know he posted one within the past month or
so.
"Poe" <Poe34@mail.com> wrote in message
news:ZgaWe.3016$6Z1.752554@news20.bellglobal.com.. .
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
the pins are trying to compensate for a vacuum leak (open vacuum port).
I'm sure Bill will shortly post a link for the vacuum diagram, so I won't
bother looking for it for you. I know he posted one within the past month or
so.
"Poe" <Poe34@mail.com> wrote in message
news:ZgaWe.3016$6Z1.752554@news20.bellglobal.com.. .
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
It is seeking a stable mix and the vacuum leaks are not letting it.
The Haynes manual for the CJ7 has a perfect carb diagram and anything
else related to the 258 engine. The YJ book sucks.
Which lines are missing and which are blocked? I am pretty good with
those carbs, maybe I can point you the right way.
Here is a link with the schematic for the vacuum lines, just click on
the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Poe wrote:
>
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
The Haynes manual for the CJ7 has a perfect carb diagram and anything
else related to the 258 engine. The YJ book sucks.
Which lines are missing and which are blocked? I am pretty good with
those carbs, maybe I can point you the right way.
Here is a link with the schematic for the vacuum lines, just click on
the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Poe wrote:
>
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
It is seeking a stable mix and the vacuum leaks are not letting it.
The Haynes manual for the CJ7 has a perfect carb diagram and anything
else related to the 258 engine. The YJ book sucks.
Which lines are missing and which are blocked? I am pretty good with
those carbs, maybe I can point you the right way.
Here is a link with the schematic for the vacuum lines, just click on
the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Poe wrote:
>
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
The Haynes manual for the CJ7 has a perfect carb diagram and anything
else related to the 258 engine. The YJ book sucks.
Which lines are missing and which are blocked? I am pretty good with
those carbs, maybe I can point you the right way.
Here is a link with the schematic for the vacuum lines, just click on
the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Poe wrote:
>
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
It is seeking a stable mix and the vacuum leaks are not letting it.
The Haynes manual for the CJ7 has a perfect carb diagram and anything
else related to the 258 engine. The YJ book sucks.
Which lines are missing and which are blocked? I am pretty good with
those carbs, maybe I can point you the right way.
Here is a link with the schematic for the vacuum lines, just click on
the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Poe wrote:
>
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
The Haynes manual for the CJ7 has a perfect carb diagram and anything
else related to the 258 engine. The YJ book sucks.
Which lines are missing and which are blocked? I am pretty good with
those carbs, maybe I can point you the right way.
Here is a link with the schematic for the vacuum lines, just click on
the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Poe wrote:
>
> OK, another question. During idle the stepper motor is constantly moving
> the needle in and out adjusting the mixture to the point of nearly
> stalling and back again. Could this be the result of a bad O2 sensor?
> Also I have a couple of vacuum ports on the carb that are not connected
> to anything, one is blocked and two are open. Where can I get a
> schematic of this carb (carter).
>
> Thanks in advance, everyone here has been a tremendous help.
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
Mike Romain says...
> It is seeking a stable mix and the vacuum leaks are not letting it.
>
> The Haynes manual for the CJ7 has a perfect carb diagram and anything
> else related to the 258 engine. The YJ book sucks.
>
> Which lines are missing and which are blocked? I am pretty good with
> those carbs, maybe I can point you the right way.
>
> Here is a link with the schematic for the vacuum lines, just click on
> the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
>
Or maybe this one :)
http://home.sprynet.com/~dale02/vactails.htm
--
Dale Beckett
> It is seeking a stable mix and the vacuum leaks are not letting it.
>
> The Haynes manual for the CJ7 has a perfect carb diagram and anything
> else related to the 258 engine. The YJ book sucks.
>
> Which lines are missing and which are blocked? I am pretty good with
> those carbs, maybe I can point you the right way.
>
> Here is a link with the schematic for the vacuum lines, just click on
> the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
>
Or maybe this one :)
http://home.sprynet.com/~dale02/vactails.htm
--
Dale Beckett
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
Mike Romain says...
> It is seeking a stable mix and the vacuum leaks are not letting it.
>
> The Haynes manual for the CJ7 has a perfect carb diagram and anything
> else related to the 258 engine. The YJ book sucks.
>
> Which lines are missing and which are blocked? I am pretty good with
> those carbs, maybe I can point you the right way.
>
> Here is a link with the schematic for the vacuum lines, just click on
> the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
>
Or maybe this one :)
http://home.sprynet.com/~dale02/vactails.htm
--
Dale Beckett
> It is seeking a stable mix and the vacuum leaks are not letting it.
>
> The Haynes manual for the CJ7 has a perfect carb diagram and anything
> else related to the 258 engine. The YJ book sucks.
>
> Which lines are missing and which are blocked? I am pretty good with
> those carbs, maybe I can point you the right way.
>
> Here is a link with the schematic for the vacuum lines, just click on
> the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
>
Or maybe this one :)
http://home.sprynet.com/~dale02/vactails.htm
--
Dale Beckett
Guest
Posts: n/a
Re: O2 sensor? 89 YJ
Mike Romain says...
> It is seeking a stable mix and the vacuum leaks are not letting it.
>
> The Haynes manual for the CJ7 has a perfect carb diagram and anything
> else related to the 258 engine. The YJ book sucks.
>
> Which lines are missing and which are blocked? I am pretty good with
> those carbs, maybe I can point you the right way.
>
> Here is a link with the schematic for the vacuum lines, just click on
> the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
>
Or maybe this one :)
http://home.sprynet.com/~dale02/vactails.htm
--
Dale Beckett
> It is seeking a stable mix and the vacuum leaks are not letting it.
>
> The Haynes manual for the CJ7 has a perfect carb diagram and anything
> else related to the 258 engine. The YJ book sucks.
>
> Which lines are missing and which are blocked? I am pretty good with
> those carbs, maybe I can point you the right way.
>
> Here is a link with the schematic for the vacuum lines, just click on
> the diagrams: http://home.sprynet.com/~dale02/ignmods.htm
>
Or maybe this one :)
http://home.sprynet.com/~dale02/vactails.htm
--
Dale Beckett
