|
noslip codechart?
I'm trying to find what noslip model I have. Anyone have a link where I can
look up the codes printed on it? dfj10c6 chj0d6 reb0ge Nick -- Nick http://members.cox.net/nnote/ |
Re: noslip codechart?
Powertrax (the manufacturer of No-Slip) has a toll free number:
1-800-578-1020. That number is for technical assistance, I am sure that they can help you there. Jerry "Nick N" <nnote@despammed.com> wrote in message news:G261c.9545$Zp.1463@fed1read07... > I'm trying to find what noslip model I have. Anyone have a link where I can > look up the codes printed on it? > dfj10c6 chj0d6 reb0ge > Nick > > -- > Nick > http://members.cox.net/nnote/ > > |
Re: noslip codechart?
Powertrax (the manufacturer of No-Slip) has a toll free number:
1-800-578-1020. That number is for technical assistance, I am sure that they can help you there. Jerry "Nick N" <nnote@despammed.com> wrote in message news:G261c.9545$Zp.1463@fed1read07... > I'm trying to find what noslip model I have. Anyone have a link where I can > look up the codes printed on it? > dfj10c6 chj0d6 reb0ge > Nick > > -- > Nick > http://members.cox.net/nnote/ > > |
Re: noslip codechart?
Powertrax (the manufacturer of No-Slip) has a toll free number:
1-800-578-1020. That number is for technical assistance, I am sure that they can help you there. Jerry "Nick N" <nnote@despammed.com> wrote in message news:G261c.9545$Zp.1463@fed1read07... > I'm trying to find what noslip model I have. Anyone have a link where I can > look up the codes printed on it? > dfj10c6 chj0d6 reb0ge > Nick > > -- > Nick > http://members.cox.net/nnote/ > > |
Re: noslip codechart?
Thanks Jerry
I had been looking for that number. I talked to tech assist at another place and he said no problem it should fit, but I tried again today and it's about an 1/8 inch to big. just barely....ya, without thrust washers.... I'll try that number tommorow. Nick "Jerry Newton" <figatmcttelecom.com> wrote in message news:40453311$1_3@newspeer2.tds.net... > Powertrax (the manufacturer of No-Slip) has a toll free number: > 1-800-578-1020. That number is for technical assistance, I am sure that > they can help you there. > > Jerry > > > "Nick N" <nnote@despammed.com> wrote in message > news:G261c.9545$Zp.1463@fed1read07... > > I'm trying to find what noslip model I have. Anyone have a link where I > can > > look up the codes printed on it? > > dfj10c6 chj0d6 reb0ge > > Nick > > > > -- > > Nick > > http://members.cox.net/nnote/ > > > > > > |
Re: noslip codechart?
Thanks Jerry
I had been looking for that number. I talked to tech assist at another place and he said no problem it should fit, but I tried again today and it's about an 1/8 inch to big. just barely....ya, without thrust washers.... I'll try that number tommorow. Nick "Jerry Newton" <figatmcttelecom.com> wrote in message news:40453311$1_3@newspeer2.tds.net... > Powertrax (the manufacturer of No-Slip) has a toll free number: > 1-800-578-1020. That number is for technical assistance, I am sure that > they can help you there. > > Jerry > > > "Nick N" <nnote@despammed.com> wrote in message > news:G261c.9545$Zp.1463@fed1read07... > > I'm trying to find what noslip model I have. Anyone have a link where I > can > > look up the codes printed on it? > > dfj10c6 chj0d6 reb0ge > > Nick > > > > -- > > Nick > > http://members.cox.net/nnote/ > > > > > > |
Re: noslip codechart?
Thanks Jerry
I had been looking for that number. I talked to tech assist at another place and he said no problem it should fit, but I tried again today and it's about an 1/8 inch to big. just barely....ya, without thrust washers.... I'll try that number tommorow. Nick "Jerry Newton" <figatmcttelecom.com> wrote in message news:40453311$1_3@newspeer2.tds.net... > Powertrax (the manufacturer of No-Slip) has a toll free number: > 1-800-578-1020. That number is for technical assistance, I am sure that > they can help you there. > > Jerry > > > "Nick N" <nnote@despammed.com> wrote in message > news:G261c.9545$Zp.1463@fed1read07... > > I'm trying to find what noslip model I have. Anyone have a link where I > can > > look up the codes printed on it? > > dfj10c6 chj0d6 reb0ge > > Nick > > > > -- > > Nick > > http://members.cox.net/nnote/ > > > > > > |
Re: noslip codechart?
Hi Nick,
Not all Dana 35C carriers are created equal. D35C with ABS used a carrier with a smaller diameter bore for the side gears than that in the non-ABS version. Also, the interior distance between the two sides is slightly wider in the ABS version. Thus, the side gear crowns (and c-clip mounting surfaces) are a bit taller for the ABS than they are for the non ABS. The ABS/non-ABS distinction was apparently maintained until 1992 or thereabout. After that, all carriers were ABS version, regardless of whether the Jeep came with ABS. Does your locker have any play in the side gear bores? Do you have enough room to install without the thrust washers? If so, you are trying to fit an ABS No-slip into a non-ABS carrier. Hope this helps. Steve Nick N wrote: > Thanks Jerry > I had been looking for that number. I talked to tech assist at another > place and he said no problem it should fit, but I tried again today and it's > about an 1/8 inch to big. just barely....ya, without thrust washers.... > I'll try that number tommorow. > Nick |
Re: noslip codechart?
Hi Nick,
Not all Dana 35C carriers are created equal. D35C with ABS used a carrier with a smaller diameter bore for the side gears than that in the non-ABS version. Also, the interior distance between the two sides is slightly wider in the ABS version. Thus, the side gear crowns (and c-clip mounting surfaces) are a bit taller for the ABS than they are for the non ABS. The ABS/non-ABS distinction was apparently maintained until 1992 or thereabout. After that, all carriers were ABS version, regardless of whether the Jeep came with ABS. Does your locker have any play in the side gear bores? Do you have enough room to install without the thrust washers? If so, you are trying to fit an ABS No-slip into a non-ABS carrier. Hope this helps. Steve Nick N wrote: > Thanks Jerry > I had been looking for that number. I talked to tech assist at another > place and he said no problem it should fit, but I tried again today and it's > about an 1/8 inch to big. just barely....ya, without thrust washers.... > I'll try that number tommorow. > Nick |
Re: noslip codechart?
Hi Nick,
Not all Dana 35C carriers are created equal. D35C with ABS used a carrier with a smaller diameter bore for the side gears than that in the non-ABS version. Also, the interior distance between the two sides is slightly wider in the ABS version. Thus, the side gear crowns (and c-clip mounting surfaces) are a bit taller for the ABS than they are for the non ABS. The ABS/non-ABS distinction was apparently maintained until 1992 or thereabout. After that, all carriers were ABS version, regardless of whether the Jeep came with ABS. Does your locker have any play in the side gear bores? Do you have enough room to install without the thrust washers? If so, you are trying to fit an ABS No-slip into a non-ABS carrier. Hope this helps. Steve Nick N wrote: > Thanks Jerry > I had been looking for that number. I talked to tech assist at another > place and he said no problem it should fit, but I tried again today and it's > about an 1/8 inch to big. just barely....ya, without thrust washers.... > I'll try that number tommorow. > Nick |
| All times are GMT -4. The time now is 04:05 AM. |
© 2024 MH Sub I, LLC dba Internet Brands