no start and stall out
#1
Guest
Posts: n/a
no start and stall out
Thanks for any help in advance:
My problem:
1995 Jeep Cherokee 4WD 4.0
Sometimes it won't start (5 or 6 tries) but after a few minutes it
will usually start. While driving it will die on me occasionally. It
will usually start after a few cranks.
What I did so far:
I get spark;
Changed plug and distributor wires;
Replaced distributor cap, rotor and cam position sensor;
Batter voltage ok; and
Never got to the point of checking for fuel because it usually starts
before I get there.
Please help because I feel I cannot trust this vehicle on a trip. Any
ideas will be appreciated.
Thanks
Hank (from PA)
My problem:
1995 Jeep Cherokee 4WD 4.0
Sometimes it won't start (5 or 6 tries) but after a few minutes it
will usually start. While driving it will die on me occasionally. It
will usually start after a few cranks.
What I did so far:
I get spark;
Changed plug and distributor wires;
Replaced distributor cap, rotor and cam position sensor;
Batter voltage ok; and
Never got to the point of checking for fuel because it usually starts
before I get there.
Please help because I feel I cannot trust this vehicle on a trip. Any
ideas will be appreciated.
Thanks
Hank (from PA)
#2
Guest
Posts: n/a
Re: no start and stall out
Hi Hank,
What it is ninety, nine percent of the time is the Crankshaft
Position Sensor, or it's connection:
http://www.off-road.com/jeep/cheroke...tdcsensor.html
Although, you're due for a pump, when it doesn't start, just turn
the ignition to the on position and listen for it's run noise, it should
run for two seconds every time to turn the ignition on.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Hank wrote:
>
> Thanks for any help in advance:
>
> My problem:
>
> 1995 Jeep Cherokee 4WD 4.0
>
> Sometimes it won't start (5 or 6 tries) but after a few minutes it
> will usually start. While driving it will die on me occasionally. It
> will usually start after a few cranks.
>
> What I did so far:
>
> I get spark;
> Changed plug and distributor wires;
> Replaced distributor cap, rotor and cam position sensor;
> Batter voltage ok; and
> Never got to the point of checking for fuel because it usually starts
> before I get there.
>
> Please help because I feel I cannot trust this vehicle on a trip. Any
> ideas will be appreciated.
>
> Thanks
> Hank (from PA)
What it is ninety, nine percent of the time is the Crankshaft
Position Sensor, or it's connection:
http://www.off-road.com/jeep/cheroke...tdcsensor.html
Although, you're due for a pump, when it doesn't start, just turn
the ignition to the on position and listen for it's run noise, it should
run for two seconds every time to turn the ignition on.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Hank wrote:
>
> Thanks for any help in advance:
>
> My problem:
>
> 1995 Jeep Cherokee 4WD 4.0
>
> Sometimes it won't start (5 or 6 tries) but after a few minutes it
> will usually start. While driving it will die on me occasionally. It
> will usually start after a few cranks.
>
> What I did so far:
>
> I get spark;
> Changed plug and distributor wires;
> Replaced distributor cap, rotor and cam position sensor;
> Batter voltage ok; and
> Never got to the point of checking for fuel because it usually starts
> before I get there.
>
> Please help because I feel I cannot trust this vehicle on a trip. Any
> ideas will be appreciated.
>
> Thanks
> Hank (from PA)
#3
Guest
Posts: n/a
Re: no start and stall out
Hi Hank,
What it is ninety, nine percent of the time is the Crankshaft
Position Sensor, or it's connection:
http://www.off-road.com/jeep/cheroke...tdcsensor.html
Although, you're due for a pump, when it doesn't start, just turn
the ignition to the on position and listen for it's run noise, it should
run for two seconds every time to turn the ignition on.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Hank wrote:
>
> Thanks for any help in advance:
>
> My problem:
>
> 1995 Jeep Cherokee 4WD 4.0
>
> Sometimes it won't start (5 or 6 tries) but after a few minutes it
> will usually start. While driving it will die on me occasionally. It
> will usually start after a few cranks.
>
> What I did so far:
>
> I get spark;
> Changed plug and distributor wires;
> Replaced distributor cap, rotor and cam position sensor;
> Batter voltage ok; and
> Never got to the point of checking for fuel because it usually starts
> before I get there.
>
> Please help because I feel I cannot trust this vehicle on a trip. Any
> ideas will be appreciated.
>
> Thanks
> Hank (from PA)
What it is ninety, nine percent of the time is the Crankshaft
Position Sensor, or it's connection:
http://www.off-road.com/jeep/cheroke...tdcsensor.html
Although, you're due for a pump, when it doesn't start, just turn
the ignition to the on position and listen for it's run noise, it should
run for two seconds every time to turn the ignition on.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Hank wrote:
>
> Thanks for any help in advance:
>
> My problem:
>
> 1995 Jeep Cherokee 4WD 4.0
>
> Sometimes it won't start (5 or 6 tries) but after a few minutes it
> will usually start. While driving it will die on me occasionally. It
> will usually start after a few cranks.
>
> What I did so far:
>
> I get spark;
> Changed plug and distributor wires;
> Replaced distributor cap, rotor and cam position sensor;
> Batter voltage ok; and
> Never got to the point of checking for fuel because it usually starts
> before I get there.
>
> Please help because I feel I cannot trust this vehicle on a trip. Any
> ideas will be appreciated.
>
> Thanks
> Hank (from PA)
#4
Guest
Posts: n/a
Re: no start and stall out
Hi Hank,
What it is ninety, nine percent of the time is the Crankshaft
Position Sensor, or it's connection:
http://www.off-road.com/jeep/cheroke...tdcsensor.html
Although, you're due for a pump, when it doesn't start, just turn
the ignition to the on position and listen for it's run noise, it should
run for two seconds every time to turn the ignition on.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Hank wrote:
>
> Thanks for any help in advance:
>
> My problem:
>
> 1995 Jeep Cherokee 4WD 4.0
>
> Sometimes it won't start (5 or 6 tries) but after a few minutes it
> will usually start. While driving it will die on me occasionally. It
> will usually start after a few cranks.
>
> What I did so far:
>
> I get spark;
> Changed plug and distributor wires;
> Replaced distributor cap, rotor and cam position sensor;
> Batter voltage ok; and
> Never got to the point of checking for fuel because it usually starts
> before I get there.
>
> Please help because I feel I cannot trust this vehicle on a trip. Any
> ideas will be appreciated.
>
> Thanks
> Hank (from PA)
What it is ninety, nine percent of the time is the Crankshaft
Position Sensor, or it's connection:
http://www.off-road.com/jeep/cheroke...tdcsensor.html
Although, you're due for a pump, when it doesn't start, just turn
the ignition to the on position and listen for it's run noise, it should
run for two seconds every time to turn the ignition on.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Hank wrote:
>
> Thanks for any help in advance:
>
> My problem:
>
> 1995 Jeep Cherokee 4WD 4.0
>
> Sometimes it won't start (5 or 6 tries) but after a few minutes it
> will usually start. While driving it will die on me occasionally. It
> will usually start after a few cranks.
>
> What I did so far:
>
> I get spark;
> Changed plug and distributor wires;
> Replaced distributor cap, rotor and cam position sensor;
> Batter voltage ok; and
> Never got to the point of checking for fuel because it usually starts
> before I get there.
>
> Please help because I feel I cannot trust this vehicle on a trip. Any
> ideas will be appreciated.
>
> Thanks
> Hank (from PA)
#5
Guest
Posts: n/a
Re: no start and stall out
Thanks Bill, will give the crankshaft PS a look-see.
Hank
On Fri, 24 Sep 2004 12:41:10 -0700, L.W.(ßill) ------ III
<----------@***.net> wrote:
>Hi Hank,
> What it is ninety, nine percent of the time is the Crankshaft
>Position Sensor, or it's connection:
>http://www.off-road.com/jeep/cheroke...tdcsensor.html
> Although, you're due for a pump, when it doesn't start, just turn
>the ignition to the on position and listen for it's run noise, it should
>run for two seconds every time to turn the ignition on.
> God Bless America, ßill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>Hank wrote:
>>
>> Thanks for any help in advance:
>>
>> My problem:
>>
>> 1995 Jeep Cherokee 4WD 4.0
>>
>> Sometimes it won't start (5 or 6 tries) but after a few minutes it
>> will usually start. While driving it will die on me occasionally. It
>> will usually start after a few cranks.
>>
>> What I did so far:
>>
>> I get spark;
>> Changed plug and distributor wires;
>> Replaced distributor cap, rotor and cam position sensor;
>> Batter voltage ok; and
>> Never got to the point of checking for fuel because it usually starts
>> before I get there.
>>
>> Please help because I feel I cannot trust this vehicle on a trip. Any
>> ideas will be appreciated.
>>
>> Thanks
>> Hank (from PA)
Hank
On Fri, 24 Sep 2004 12:41:10 -0700, L.W.(ßill) ------ III
<----------@***.net> wrote:
>Hi Hank,
> What it is ninety, nine percent of the time is the Crankshaft
>Position Sensor, or it's connection:
>http://www.off-road.com/jeep/cheroke...tdcsensor.html
> Although, you're due for a pump, when it doesn't start, just turn
>the ignition to the on position and listen for it's run noise, it should
>run for two seconds every time to turn the ignition on.
> God Bless America, ßill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>Hank wrote:
>>
>> Thanks for any help in advance:
>>
>> My problem:
>>
>> 1995 Jeep Cherokee 4WD 4.0
>>
>> Sometimes it won't start (5 or 6 tries) but after a few minutes it
>> will usually start. While driving it will die on me occasionally. It
>> will usually start after a few cranks.
>>
>> What I did so far:
>>
>> I get spark;
>> Changed plug and distributor wires;
>> Replaced distributor cap, rotor and cam position sensor;
>> Batter voltage ok; and
>> Never got to the point of checking for fuel because it usually starts
>> before I get there.
>>
>> Please help because I feel I cannot trust this vehicle on a trip. Any
>> ideas will be appreciated.
>>
>> Thanks
>> Hank (from PA)
#6
Guest
Posts: n/a
Re: no start and stall out
Thanks Bill, will give the crankshaft PS a look-see.
Hank
On Fri, 24 Sep 2004 12:41:10 -0700, L.W.(ßill) ------ III
<----------@***.net> wrote:
>Hi Hank,
> What it is ninety, nine percent of the time is the Crankshaft
>Position Sensor, or it's connection:
>http://www.off-road.com/jeep/cheroke...tdcsensor.html
> Although, you're due for a pump, when it doesn't start, just turn
>the ignition to the on position and listen for it's run noise, it should
>run for two seconds every time to turn the ignition on.
> God Bless America, ßill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>Hank wrote:
>>
>> Thanks for any help in advance:
>>
>> My problem:
>>
>> 1995 Jeep Cherokee 4WD 4.0
>>
>> Sometimes it won't start (5 or 6 tries) but after a few minutes it
>> will usually start. While driving it will die on me occasionally. It
>> will usually start after a few cranks.
>>
>> What I did so far:
>>
>> I get spark;
>> Changed plug and distributor wires;
>> Replaced distributor cap, rotor and cam position sensor;
>> Batter voltage ok; and
>> Never got to the point of checking for fuel because it usually starts
>> before I get there.
>>
>> Please help because I feel I cannot trust this vehicle on a trip. Any
>> ideas will be appreciated.
>>
>> Thanks
>> Hank (from PA)
Hank
On Fri, 24 Sep 2004 12:41:10 -0700, L.W.(ßill) ------ III
<----------@***.net> wrote:
>Hi Hank,
> What it is ninety, nine percent of the time is the Crankshaft
>Position Sensor, or it's connection:
>http://www.off-road.com/jeep/cheroke...tdcsensor.html
> Although, you're due for a pump, when it doesn't start, just turn
>the ignition to the on position and listen for it's run noise, it should
>run for two seconds every time to turn the ignition on.
> God Bless America, ßill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>Hank wrote:
>>
>> Thanks for any help in advance:
>>
>> My problem:
>>
>> 1995 Jeep Cherokee 4WD 4.0
>>
>> Sometimes it won't start (5 or 6 tries) but after a few minutes it
>> will usually start. While driving it will die on me occasionally. It
>> will usually start after a few cranks.
>>
>> What I did so far:
>>
>> I get spark;
>> Changed plug and distributor wires;
>> Replaced distributor cap, rotor and cam position sensor;
>> Batter voltage ok; and
>> Never got to the point of checking for fuel because it usually starts
>> before I get there.
>>
>> Please help because I feel I cannot trust this vehicle on a trip. Any
>> ideas will be appreciated.
>>
>> Thanks
>> Hank (from PA)
#7
Guest
Posts: n/a
Re: no start and stall out
Thanks Bill, will give the crankshaft PS a look-see.
Hank
On Fri, 24 Sep 2004 12:41:10 -0700, L.W.(ßill) ------ III
<----------@***.net> wrote:
>Hi Hank,
> What it is ninety, nine percent of the time is the Crankshaft
>Position Sensor, or it's connection:
>http://www.off-road.com/jeep/cheroke...tdcsensor.html
> Although, you're due for a pump, when it doesn't start, just turn
>the ignition to the on position and listen for it's run noise, it should
>run for two seconds every time to turn the ignition on.
> God Bless America, ßill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>Hank wrote:
>>
>> Thanks for any help in advance:
>>
>> My problem:
>>
>> 1995 Jeep Cherokee 4WD 4.0
>>
>> Sometimes it won't start (5 or 6 tries) but after a few minutes it
>> will usually start. While driving it will die on me occasionally. It
>> will usually start after a few cranks.
>>
>> What I did so far:
>>
>> I get spark;
>> Changed plug and distributor wires;
>> Replaced distributor cap, rotor and cam position sensor;
>> Batter voltage ok; and
>> Never got to the point of checking for fuel because it usually starts
>> before I get there.
>>
>> Please help because I feel I cannot trust this vehicle on a trip. Any
>> ideas will be appreciated.
>>
>> Thanks
>> Hank (from PA)
Hank
On Fri, 24 Sep 2004 12:41:10 -0700, L.W.(ßill) ------ III
<----------@***.net> wrote:
>Hi Hank,
> What it is ninety, nine percent of the time is the Crankshaft
>Position Sensor, or it's connection:
>http://www.off-road.com/jeep/cheroke...tdcsensor.html
> Although, you're due for a pump, when it doesn't start, just turn
>the ignition to the on position and listen for it's run noise, it should
>run for two seconds every time to turn the ignition on.
> God Bless America, ßill O|||||||O
>mailto:-------------------- http://www.----------.com/
>
>Hank wrote:
>>
>> Thanks for any help in advance:
>>
>> My problem:
>>
>> 1995 Jeep Cherokee 4WD 4.0
>>
>> Sometimes it won't start (5 or 6 tries) but after a few minutes it
>> will usually start. While driving it will die on me occasionally. It
>> will usually start after a few cranks.
>>
>> What I did so far:
>>
>> I get spark;
>> Changed plug and distributor wires;
>> Replaced distributor cap, rotor and cam position sensor;
>> Batter voltage ok; and
>> Never got to the point of checking for fuel because it usually starts
>> before I get there.
>>
>> Please help because I feel I cannot trust this vehicle on a trip. Any
>> ideas will be appreciated.
>>
>> Thanks
>> Hank (from PA)
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)