New Distibutor and still no start. No spark.
Guest
Posts: n/a
New Distibutor and still no start. No spark.
I'm still not getting back any error codes. I installed a new distributor.
Made sure I cleaned out the pin holes in the connector on the wiring
harness. What else to do?
Is there a way to test other parts (coil, etc) with a multimeter to make
sure it's working correctly?
I sure hate to just start throwing parts at it.
Thanks in advance,
bill
Made sure I cleaned out the pin holes in the connector on the wiring
harness. What else to do?
Is there a way to test other parts (coil, etc) with a multimeter to make
sure it's working correctly?
I sure hate to just start throwing parts at it.
Thanks in advance,
bill
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
Ok, I figured it out. I didn't set the distributor on the COMPRESSION
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
Ok, I figured it out. I didn't set the distributor on the COMPRESSION
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
Ok, I figured it out. I didn't set the distributor on the COMPRESSION
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
Ok, I figured it out. I didn't set the distributor on the COMPRESSION
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
stroke. Duhhh!!!.
Back in business.
Now, on this week to check the injectors.
Thanks all,
Bill
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:2gq8dnF5m5bjU1@uni-berlin.de...
> I'm still not getting back any error codes. I installed a new
distributor.
> Made sure I cleaned out the pin holes in the connector on the wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
>
>
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
William Oliveri wrote:
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
William Oliveri wrote:
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
William Oliveri wrote:
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
Guest
Posts: n/a
Re: New Distibutor and still no start. No spark.
William Oliveri wrote:
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
> I'm still not getting back any error codes. I installed a new
> distributor. Made sure I cleaned out the pin holes in the connector on the
> wiring
> harness. What else to do?
>
> Is there a way to test other parts (coil, etc) with a multimeter to make
> sure it's working correctly?
>
> I sure hate to just start throwing parts at it.
>
>
> Thanks in advance,
>
> bill
You will something like a Haynes manual. There is a way to test the coil
with an ohm meter.
--
Say NO! To TCPA! http://www.againsttcpa.com
What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html
Thread
Thread Starter
Forum
Replies
Last Post
EricH
Jeep Mailing List
8
Jul 24, 2007 08:22 PM
Tom Russell
Jeep Mailing List
45
Nov 19, 2003 05:32 PM
Rico de Lara
Jeep Mailing List
6
Nov 17, 2003 08:43 AM
Rico de Lara
Jeep Mailing List
0
Nov 16, 2003 11:48 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
