Need a clutch?
10-07-2003, 07:22 PM
#2
Guest
Posts: n/a
Re: Need a clutch?
Adjusting.
You worry when it is at the top and can't adjust any more down.
I set mine up higher than 'I' like it so my wife with short legs can
drive it easily. I am 6'4" with a 37" inseam and my wife is 5'2".
The book says you should have 1/2" of flop at the top end of the pedal.
If not, you have linkage or mount issues likely.
You might want to check the pivot points on the linkage. If an engine
or tranny mount is bad, the clutch pedal will change radically. The bar
from the body to the bell housing also needs grease witch most folks
don't know, there is a grease nipple on it.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ABanks5@columbus.rr.com wrote:
>
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine. I
> just bought it last week. Or does it need adjusting??
> Allen
You worry when it is at the top and can't adjust any more down.
I set mine up higher than 'I' like it so my wife with short legs can
drive it easily. I am 6'4" with a 37" inseam and my wife is 5'2".
The book says you should have 1/2" of flop at the top end of the pedal.
If not, you have linkage or mount issues likely.
You might want to check the pivot points on the linkage. If an engine
or tranny mount is bad, the clutch pedal will change radically. The bar
from the body to the bell housing also needs grease witch most folks
don't know, there is a grease nipple on it.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ABanks5@columbus.rr.com wrote:
>
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine. I
> just bought it last week. Or does it need adjusting??
> Allen
10-07-2003, 07:22 PM
#3
Guest
Posts: n/a
Re: Need a clutch?
Adjusting.
You worry when it is at the top and can't adjust any more down.
I set mine up higher than 'I' like it so my wife with short legs can
drive it easily. I am 6'4" with a 37" inseam and my wife is 5'2".
The book says you should have 1/2" of flop at the top end of the pedal.
If not, you have linkage or mount issues likely.
You might want to check the pivot points on the linkage. If an engine
or tranny mount is bad, the clutch pedal will change radically. The bar
from the body to the bell housing also needs grease witch most folks
don't know, there is a grease nipple on it.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ABanks5@columbus.rr.com wrote:
>
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine. I
> just bought it last week. Or does it need adjusting??
> Allen
You worry when it is at the top and can't adjust any more down.
I set mine up higher than 'I' like it so my wife with short legs can
drive it easily. I am 6'4" with a 37" inseam and my wife is 5'2".
The book says you should have 1/2" of flop at the top end of the pedal.
If not, you have linkage or mount issues likely.
You might want to check the pivot points on the linkage. If an engine
or tranny mount is bad, the clutch pedal will change radically. The bar
from the body to the bell housing also needs grease witch most folks
don't know, there is a grease nipple on it.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ABanks5@columbus.rr.com wrote:
>
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine. I
> just bought it last week. Or does it need adjusting??
> Allen
10-07-2003, 07:22 PM
#4
Guest
Posts: n/a
Re: Need a clutch?
Adjusting.
You worry when it is at the top and can't adjust any more down.
I set mine up higher than 'I' like it so my wife with short legs can
drive it easily. I am 6'4" with a 37" inseam and my wife is 5'2".
The book says you should have 1/2" of flop at the top end of the pedal.
If not, you have linkage or mount issues likely.
You might want to check the pivot points on the linkage. If an engine
or tranny mount is bad, the clutch pedal will change radically. The bar
from the body to the bell housing also needs grease witch most folks
don't know, there is a grease nipple on it.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ABanks5@columbus.rr.com wrote:
>
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine. I
> just bought it last week. Or does it need adjusting??
> Allen
You worry when it is at the top and can't adjust any more down.
I set mine up higher than 'I' like it so my wife with short legs can
drive it easily. I am 6'4" with a 37" inseam and my wife is 5'2".
The book says you should have 1/2" of flop at the top end of the pedal.
If not, you have linkage or mount issues likely.
You might want to check the pivot points on the linkage. If an engine
or tranny mount is bad, the clutch pedal will change radically. The bar
from the body to the bell housing also needs grease witch most folks
don't know, there is a grease nipple on it.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ABanks5@columbus.rr.com wrote:
>
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine. I
> just bought it last week. Or does it need adjusting??
> Allen
10-07-2003, 07:29 PM
#5
Guest
Posts: n/a
Re: Need a clutch?
Needs adjusting... did you install it?
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
<ABanks5@columbus.rr.com> wrote in message
news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine.
I
> just bought it last week. Or does it need adjusting??
> Allen
>
>
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
<ABanks5@columbus.rr.com> wrote in message
news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine.
I
> just bought it last week. Or does it need adjusting??
> Allen
>
>
10-07-2003, 07:29 PM
#6
Guest
Posts: n/a
Re: Need a clutch?
Needs adjusting... did you install it?
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
<ABanks5@columbus.rr.com> wrote in message
news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine.
I
> just bought it last week. Or does it need adjusting??
> Allen
>
>
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
<ABanks5@columbus.rr.com> wrote in message
news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine.
I
> just bought it last week. Or does it need adjusting??
> Allen
>
>
10-07-2003, 07:29 PM
#7
Guest
Posts: n/a
Re: Need a clutch?
Needs adjusting... did you install it?
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
<ABanks5@columbus.rr.com> wrote in message
news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine.
I
> just bought it last week. Or does it need adjusting??
> Allen
>
>
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
<ABanks5@columbus.rr.com> wrote in message
news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab fine.
I
> just bought it last week. Or does it need adjusting??
> Allen
>
>
10-07-2003, 08:35 PM
#8
Guest
Posts: n/a
Re: Need a clutch?
No it was like that when I got it. It's a YJ tub on a CJ...wonder if there
is adjustment issues that can't be resolved. Will get under there tomorrow.
Thanks!
"JimG" <jimg@cj7.com> wrote in message news:6%Hgb.38$091.25@news02.roc.ny...
> Needs adjusting... did you install it?
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> <ABanks5@columbus.rr.com> wrote in message
> news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> > My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab
fine.
> I
> > just bought it last week. Or does it need adjusting??
> > Allen
> >
> >
>
>
is adjustment issues that can't be resolved. Will get under there tomorrow.
Thanks!
"JimG" <jimg@cj7.com> wrote in message news:6%Hgb.38$091.25@news02.roc.ny...
> Needs adjusting... did you install it?
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> <ABanks5@columbus.rr.com> wrote in message
> news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> > My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab
fine.
> I
> > just bought it last week. Or does it need adjusting??
> > Allen
> >
> >
>
>
10-07-2003, 08:35 PM
#9
Guest
Posts: n/a
Re: Need a clutch?
No it was like that when I got it. It's a YJ tub on a CJ...wonder if there
is adjustment issues that can't be resolved. Will get under there tomorrow.
Thanks!
"JimG" <jimg@cj7.com> wrote in message news:6%Hgb.38$091.25@news02.roc.ny...
> Needs adjusting... did you install it?
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> <ABanks5@columbus.rr.com> wrote in message
> news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> > My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab
fine.
> I
> > just bought it last week. Or does it need adjusting??
> > Allen
> >
> >
>
>
is adjustment issues that can't be resolved. Will get under there tomorrow.
Thanks!
"JimG" <jimg@cj7.com> wrote in message news:6%Hgb.38$091.25@news02.roc.ny...
> Needs adjusting... did you install it?
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> <ABanks5@columbus.rr.com> wrote in message
> news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> > My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab
fine.
> I
> > just bought it last week. Or does it need adjusting??
> > Allen
> >
> >
>
>
10-07-2003, 08:35 PM
#10
Guest
Posts: n/a
Re: Need a clutch?
No it was like that when I got it. It's a YJ tub on a CJ...wonder if there
is adjustment issues that can't be resolved. Will get under there tomorrow.
Thanks!
"JimG" <jimg@cj7.com> wrote in message news:6%Hgb.38$091.25@news02.roc.ny...
> Needs adjusting... did you install it?
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> <ABanks5@columbus.rr.com> wrote in message
> news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> > My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab
fine.
> I
> > just bought it last week. Or does it need adjusting??
> > Allen
> >
> >
>
>
is adjustment issues that can't be resolved. Will get under there tomorrow.
Thanks!
"JimG" <jimg@cj7.com> wrote in message news:6%Hgb.38$091.25@news02.roc.ny...
> Needs adjusting... did you install it?
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> <ABanks5@columbus.rr.com> wrote in message
> news:oGHgb.59547$uJ2.39646@fe3.columbus.rr.com...
> > My CJ clutch pedal engages 1/2 inch off the floor. It seems to grab
fine.
> I
> > just bought it last week. Or does it need adjusting??
> > Allen
> >
> >
>
>