Manual Transmission Problem
#11
Guest
Posts: n/a
Re: Manual Transmission Problem
On Feb 26, 7:03 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> poke
>
>
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever
> back
> > into your fourth gear shift rod position:
> >http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com- Hide quoted text -
>
> - Show quoted text -
Thanks I will take a look at it this weekend and get back to you
guys.. I appreaciate the help...
wrote:
> poke
>
>
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever
> back
> > into your fourth gear shift rod position:
> >http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com- Hide quoted text -
>
> - Show quoted text -
Thanks I will take a look at it this weekend and get back to you
guys.. I appreaciate the help...
#12
Guest
Posts: n/a
Re: Manual Transmission Problem
On Feb 26, 7:03 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> poke
>
>
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever
> back
> > into your fourth gear shift rod position:
> >http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com- Hide quoted text -
>
> - Show quoted text -
Thanks I will take a look at it this weekend and get back to you
guys.. I appreaciate the help...
wrote:
> poke
>
>
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever
> back
> > into your fourth gear shift rod position:
> >http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com- Hide quoted text -
>
> - Show quoted text -
Thanks I will take a look at it this weekend and get back to you
guys.. I appreaciate the help...
#13
Guest
Posts: n/a
Re: Manual Transmission Problem
On Feb 26, 7:03 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> poke
>
>
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever
> back
> > into your fourth gear shift rod position:
> >http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com- Hide quoted text -
>
> - Show quoted text -
Thanks I will take a look at it this weekend and get back to you
guys.. I appreaciate the help...
wrote:
> poke
>
>
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever
> back
> > into your fourth gear shift rod position:
> >http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com- Hide quoted text -
>
> - Show quoted text -
Thanks I will take a look at it this weekend and get back to you
guys.. I appreaciate the help...
#14
Guest
Posts: n/a
Re: Manual Transmission Problem
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
#15
Guest
Posts: n/a
Re: Manual Transmission Problem
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
#16
Guest
Posts: n/a
Re: Manual Transmission Problem
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
#17
Guest
Posts: n/a
Re: Manual Transmission Problem
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
#18
Guest
Posts: n/a
Re: Manual Transmission Problem
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
#19
Guest
Posts: n/a
Re: Manual Transmission Problem
On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
wrote:
> You need to replace the shift lever bushing while pocking the lever back
> into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> God Bless America, Bill 0|||||||0
> mailto:LW------...@aol.comhttp://www.----------.com/
>
> "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> news:1172523764.862086.163620@h3g2000cwc.googlegro ups.com...
>
> > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > reverse. Only 4th. I can move the stick around with out the clutch
> > pressed and nothing no grinding nothing. It was on the highway coming
> > off the ramp. At the stop light nothing would engage or grind? It is
> > like and empty space? The Trans has almost 130K Last time it was
> > serviced it was 50 K old. I don't think it would be the clutch since
> > it works fine for 4th gear? Any one have any ideas?
>
> > If it is toasted is better to buy the same one new or get it rebuilt
> > or get a different kind with better gearing. I am running 33" with a 4
> > cycl engine.
>
> --
> Posted via a free Usenet account fromhttp://www.teranews.com
Ok I took it apart. The bushing is ok. While I shift I can hear a
whine but pretty faint. Almost like it is just spinning. I shifted
with a screw driver and same thing. No gears except 4th. I am assuming
I need a trans rebuilt now. Any ideas on where to start? Or
alternatives instead of rebuilding?
#20
Guest
Posts: n/a
Re: Manual Transmission Problem
On Mar 4, 8:32 am, "barrios35" <jamesbarr...@gmail.com> wrote:
> On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> wrote:
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever back
> > into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
>
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> Ok I took it apart. The bushing is ok. While I shift I can hear a
> whine but pretty faint. Almost like it is just spinning. I shifted
> with a screw driver and same thing. No gears except 4th. I am assuming
> I need a trans rebuilt now. Any ideas on where to start? Or
> alternatives instead of rebuilding?- Hide quoted text -
>
> - Show quoted text -
Maybe a rebuilding kit I can buy?
> On Feb 26, 6:51 pm, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> wrote:
>
>
>
>
>
> > You need to replace the shift lever bushing while pocking the lever back
> > into your fourth gear shift rod position:http://www.quadratec.com/products/52111_02.htm
> > God Bless America, Bill 0|||||||0
> > mailto:LW------...@aol.comhttp://www.----------.com/
>
> > "barrios35" <jamesbarr...@gmail.com> wrote in message
>
> >news:1172523764.862086.163620@h3g2000cwc.googlegr oups.com...
>
> > > My 94 wrangler manual Trans does not engage 1st, 2nd, 3rd, 5th or
> > > reverse. Only 4th. I can move the stick around with out the clutch
> > > pressed and nothing no grinding nothing. It was on the highway coming
> > > off the ramp. At the stop light nothing would engage or grind? It is
> > > like and empty space? The Trans has almost 130K Last time it was
> > > serviced it was 50 K old. I don't think it would be the clutch since
> > > it works fine for 4th gear? Any one have any ideas?
>
> > > If it is toasted is better to buy the same one new or get it rebuilt
> > > or get a different kind with better gearing. I am running 33" with a 4
> > > cycl engine.
>
> > --
> > Posted via a free Usenet account fromhttp://www.teranews.com
>
> Ok I took it apart. The bushing is ok. While I shift I can hear a
> whine but pretty faint. Almost like it is just spinning. I shifted
> with a screw driver and same thing. No gears except 4th. I am assuming
> I need a trans rebuilt now. Any ideas on where to start? Or
> alternatives instead of rebuilding?- Hide quoted text -
>
> - Show quoted text -
Maybe a rebuilding kit I can buy?