LP Dana 30 Housings
Guest
Posts: n/a
LP Dana 30 Housings
Can anybody tell me whether the Dana 30 axle housings and gears are the same
or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
are both low pinion housings with 3.73 gears. The Grand has CV shafts and
ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
count of the axle shafts is the same right? There may be some difference in
the knuckles that I don't care about, and the Grand has some sort of fancy
doohickey on the front of the front driveshaft, but the pinions should be
the same, eh?
The reason I ask is because the bearings are shot in the Grand Cherokee's
font axle (they're making noise) and I'm in the process of swapping out the
TJ front axle. I thinking of bolting the TJ's Dana 30 housing onto the ZJ,
keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
/Peter
or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
are both low pinion housings with 3.73 gears. The Grand has CV shafts and
ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
count of the axle shafts is the same right? There may be some difference in
the knuckles that I don't care about, and the Grand has some sort of fancy
doohickey on the front of the front driveshaft, but the pinions should be
the same, eh?
The reason I ask is because the bearings are shot in the Grand Cherokee's
font axle (they're making noise) and I'm in the process of swapping out the
TJ front axle. I thinking of bolting the TJ's Dana 30 housing onto the ZJ,
keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
/Peter
Guest
Posts: n/a
Re: LP Dana 30 Housings
No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
Guest
Posts: n/a
Re: LP Dana 30 Housings
No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
Guest
Posts: n/a
Re: LP Dana 30 Housings
No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
Guest
Posts: n/a
Re: LP Dana 30 Housings
No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
hard to believe ...
/Peter
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> Can anybody tell me whether the Dana 30 axle housings and gears are the
same
> or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited? They
> are both low pinion housings with 3.73 gears. The Grand has CV shafts and
> ABS, the TJ has good old U-Joints and no ABS. However, the size and spline
> count of the axle shafts is the same right? There may be some difference
in
> the knuckles that I don't care about, and the Grand has some sort of fancy
> doohickey on the front of the front driveshaft, but the pinions should be
> the same, eh?
>
> The reason I ask is because the bearings are shot in the Grand Cherokee's
> font axle (they're making noise) and I'm in the process of swapping out
the
> TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
ZJ,
> keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
>
> /Peter
>
>
Guest
Posts: n/a
Re: LP Dana 30 Housings
Hi Pete,
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Guest
Posts: n/a
Re: LP Dana 30 Housings
Hi Pete,
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Guest
Posts: n/a
Re: LP Dana 30 Housings
Hi Pete,
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Guest
Posts: n/a
Re: LP Dana 30 Housings
Hi Pete,
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Maybe you may figure it out by ordering the parts:
http://store.summitracing.com/defaul....asp&x=31&y=12
The standard rotation 3.73 appear to be the same. I used to think a Dana
44, was a Dana 44 from the forties on, but I learned the Rubicon uses
the Japanese thinner ring gear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Peter Pontbriand wrote:
>
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
Guest
Posts: n/a
Re: LP Dana 30 Housings
Sorry Peter, wouldn't want you to bet your money on my guess .....
The Jeep dealer should tell you if the part numbers are the same.
Dave Milne, Scotland
'91 Grand Wagoneer, '99 TJ
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:fuadnVuV_Mi16eDfRVn-hA@storm.ca...
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
>
> "Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
> news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> > Can anybody tell me whether the Dana 30 axle housings and gears are the
> same
> > or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited?
They
> > are both low pinion housings with 3.73 gears. The Grand has CV shafts
and
> > ABS, the TJ has good old U-Joints and no ABS. However, the size and
spline
> > count of the axle shafts is the same right? There may be some difference
> in
> > the knuckles that I don't care about, and the Grand has some sort of
fancy
> > doohickey on the front of the front driveshaft, but the pinions should
be
> > the same, eh?
> >
> > The reason I ask is because the bearings are shot in the Grand
Cherokee's
> > font axle (they're making noise) and I'm in the process of swapping out
> the
> > TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
> ZJ,
> > keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
> >
> > /Peter
> >
> >
>
>
The Jeep dealer should tell you if the part numbers are the same.
Dave Milne, Scotland
'91 Grand Wagoneer, '99 TJ
"Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
news:fuadnVuV_Mi16eDfRVn-hA@storm.ca...
> No one on this newsgroup knows anything about recent Jeep Dana 30s? Seems
> hard to believe ...
>
> /Peter
>
> "Peter Pontbriand" <TRIMsprocketATstormDOTcaTRIM> wrote in message
> news:Gqidncif6ugWKebfRVn-3g@storm.ca...
> > Can anybody tell me whether the Dana 30 axle housings and gears are the
> same
> > or not between a 2002 TJ Sport and a '98 Grand Cherokee 5.9 Limited?
They
> > are both low pinion housings with 3.73 gears. The Grand has CV shafts
and
> > ABS, the TJ has good old U-Joints and no ABS. However, the size and
spline
> > count of the axle shafts is the same right? There may be some difference
> in
> > the knuckles that I don't care about, and the Grand has some sort of
fancy
> > doohickey on the front of the front driveshaft, but the pinions should
be
> > the same, eh?
> >
> > The reason I ask is because the bearings are shot in the Grand
Cherokee's
> > font axle (they're making noise) and I'm in the process of swapping out
> the
> > TJ front axle. I'm thinking of bolting the TJ's Dana 30 housing onto the
> ZJ,
> > keeping the ZJ knuckles and axle shafts on the ZJ. Will this work?
> >
> > /Peter
> >
> >
>
>
