Lift & Driveline problems
#62
Guest
Posts: n/a
Re: Lift & Driveline problems
I disagree with this. Yes, if the t-case was kept at the stock height,
the motor mount lift would help in the driveline angles of the rear
driveshaft. However, he plans to put a new skid plate on to raise the
transfer case up. This will effectively negate the potential help that
raising the engine would have done. Sound right?
"Jerry Bransford" <jerrypb@mecox.net> wrote in message news:<8QiIb.33110$gN.24234@fed1read05>...
> Your driveshaft length will be fine with that height lift. With a 2"
> suspension lift, it's common that the transfer case may have to be dropped a
> little to eliminate vibrations... but that you're installing a 1.5" engine
> lift will eliminate that need. Lifting the engine at the front works the
> same as dropping the t-case a little to reduce the angles that can cause
> drivetrain vibrations. You should be perfectly fine with that combination.
>
> Jerry
> --
> Jerry Bransford
> To email, remove 'me' from my email address
> KC6TAY, PP-ASEL
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
>
> "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > skidplate. What driveline problems should I expect, what do I need to
> > buy in advance to fix the problems, how do I fix it, and will I need
> > to have custom driveshafts made?
> >
> > Thanks for your time and help,
> >
> > Andrew Whitley
the motor mount lift would help in the driveline angles of the rear
driveshaft. However, he plans to put a new skid plate on to raise the
transfer case up. This will effectively negate the potential help that
raising the engine would have done. Sound right?
"Jerry Bransford" <jerrypb@mecox.net> wrote in message news:<8QiIb.33110$gN.24234@fed1read05>...
> Your driveshaft length will be fine with that height lift. With a 2"
> suspension lift, it's common that the transfer case may have to be dropped a
> little to eliminate vibrations... but that you're installing a 1.5" engine
> lift will eliminate that need. Lifting the engine at the front works the
> same as dropping the t-case a little to reduce the angles that can cause
> drivetrain vibrations. You should be perfectly fine with that combination.
>
> Jerry
> --
> Jerry Bransford
> To email, remove 'me' from my email address
> KC6TAY, PP-ASEL
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
>
> "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > skidplate. What driveline problems should I expect, what do I need to
> > buy in advance to fix the problems, how do I fix it, and will I need
> > to have custom driveshafts made?
> >
> > Thanks for your time and help,
> >
> > Andrew Whitley
#63
Guest
Posts: n/a
Re: Lift & Driveline problems
I disagree with this. Yes, if the t-case was kept at the stock height,
the motor mount lift would help in the driveline angles of the rear
driveshaft. However, he plans to put a new skid plate on to raise the
transfer case up. This will effectively negate the potential help that
raising the engine would have done. Sound right?
"Jerry Bransford" <jerrypb@mecox.net> wrote in message news:<8QiIb.33110$gN.24234@fed1read05>...
> Your driveshaft length will be fine with that height lift. With a 2"
> suspension lift, it's common that the transfer case may have to be dropped a
> little to eliminate vibrations... but that you're installing a 1.5" engine
> lift will eliminate that need. Lifting the engine at the front works the
> same as dropping the t-case a little to reduce the angles that can cause
> drivetrain vibrations. You should be perfectly fine with that combination.
>
> Jerry
> --
> Jerry Bransford
> To email, remove 'me' from my email address
> KC6TAY, PP-ASEL
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
>
> "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > skidplate. What driveline problems should I expect, what do I need to
> > buy in advance to fix the problems, how do I fix it, and will I need
> > to have custom driveshafts made?
> >
> > Thanks for your time and help,
> >
> > Andrew Whitley
the motor mount lift would help in the driveline angles of the rear
driveshaft. However, he plans to put a new skid plate on to raise the
transfer case up. This will effectively negate the potential help that
raising the engine would have done. Sound right?
"Jerry Bransford" <jerrypb@mecox.net> wrote in message news:<8QiIb.33110$gN.24234@fed1read05>...
> Your driveshaft length will be fine with that height lift. With a 2"
> suspension lift, it's common that the transfer case may have to be dropped a
> little to eliminate vibrations... but that you're installing a 1.5" engine
> lift will eliminate that need. Lifting the engine at the front works the
> same as dropping the t-case a little to reduce the angles that can cause
> drivetrain vibrations. You should be perfectly fine with that combination.
>
> Jerry
> --
> Jerry Bransford
> To email, remove 'me' from my email address
> KC6TAY, PP-ASEL
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
>
> "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > skidplate. What driveline problems should I expect, what do I need to
> > buy in advance to fix the problems, how do I fix it, and will I need
> > to have custom driveshafts made?
> >
> > Thanks for your time and help,
> >
> > Andrew Whitley
#64
Guest
Posts: n/a
Re: Lift & Driveline problems
I disagree with this. Yes, if the t-case was kept at the stock height,
the motor mount lift would help in the driveline angles of the rear
driveshaft. However, he plans to put a new skid plate on to raise the
transfer case up. This will effectively negate the potential help that
raising the engine would have done. Sound right?
"Jerry Bransford" <jerrypb@mecox.net> wrote in message news:<8QiIb.33110$gN.24234@fed1read05>...
> Your driveshaft length will be fine with that height lift. With a 2"
> suspension lift, it's common that the transfer case may have to be dropped a
> little to eliminate vibrations... but that you're installing a 1.5" engine
> lift will eliminate that need. Lifting the engine at the front works the
> same as dropping the t-case a little to reduce the angles that can cause
> drivetrain vibrations. You should be perfectly fine with that combination.
>
> Jerry
> --
> Jerry Bransford
> To email, remove 'me' from my email address
> KC6TAY, PP-ASEL
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
>
> "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > skidplate. What driveline problems should I expect, what do I need to
> > buy in advance to fix the problems, how do I fix it, and will I need
> > to have custom driveshafts made?
> >
> > Thanks for your time and help,
> >
> > Andrew Whitley
the motor mount lift would help in the driveline angles of the rear
driveshaft. However, he plans to put a new skid plate on to raise the
transfer case up. This will effectively negate the potential help that
raising the engine would have done. Sound right?
"Jerry Bransford" <jerrypb@mecox.net> wrote in message news:<8QiIb.33110$gN.24234@fed1read05>...
> Your driveshaft length will be fine with that height lift. With a 2"
> suspension lift, it's common that the transfer case may have to be dropped a
> little to eliminate vibrations... but that you're installing a 1.5" engine
> lift will eliminate that need. Lifting the engine at the front works the
> same as dropping the t-case a little to reduce the angles that can cause
> drivetrain vibrations. You should be perfectly fine with that combination.
>
> Jerry
> --
> Jerry Bransford
> To email, remove 'me' from my email address
> KC6TAY, PP-ASEL
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
>
> "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > skidplate. What driveline problems should I expect, what do I need to
> > buy in advance to fix the problems, how do I fix it, and will I need
> > to have custom driveshafts made?
> >
> > Thanks for your time and help,
> >
> > Andrew Whitley
#65
Guest
Posts: n/a
Re: Lift & Driveline problems
Yeah you're right Bob, I did miss that he was also installing a high
clearance skidplate. Though it still may work since he's only installing a
2" suspension lift and the 1.5" engine lift is usually more than enough for
a 3" suspension lift... so it's possible that he may still get away with it.
Jerry
--
Jerry Bransford
To email, remove 'me' from my email address
KC6TAY, PP-ASEL
See the Geezer Jeep at
http://members.***.net/jerrypb/
"Bob" <magicclaw@mac.com> wrote in message
news:47b769ae.0312310859.5e46e7c8@posting.google.c om...
> I disagree with this. Yes, if the t-case was kept at the stock height,
> the motor mount lift would help in the driveline angles of the rear
> driveshaft. However, he plans to put a new skid plate on to raise the
> transfer case up. This will effectively negate the potential help that
> raising the engine would have done. Sound right?
>
>
> "Jerry Bransford" <jerrypb@mecox.net> wrote in message
news:<8QiIb.33110$gN.24234@fed1read05>...
> > Your driveshaft length will be fine with that height lift. With a 2"
> > suspension lift, it's common that the transfer case may have to be
dropped a
> > little to eliminate vibrations... but that you're installing a 1.5"
engine
> > lift will eliminate that need. Lifting the engine at the front works
the
> > same as dropping the t-case a little to reduce the angles that can cause
> > drivetrain vibrations. You should be perfectly fine with that
combination.
> >
> > Jerry
> > --
> > Jerry Bransford
> > To email, remove 'me' from my email address
> > KC6TAY, PP-ASEL
> > See the Geezer Jeep at
> > http://members.***.net/jerrypb/
> >
> > "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> > news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > > skidplate. What driveline problems should I expect, what do I need to
> > > buy in advance to fix the problems, how do I fix it, and will I need
> > > to have custom driveshafts made?
> > >
> > > Thanks for your time and help,
> > >
> > > Andrew Whitley
clearance skidplate. Though it still may work since he's only installing a
2" suspension lift and the 1.5" engine lift is usually more than enough for
a 3" suspension lift... so it's possible that he may still get away with it.
Jerry
--
Jerry Bransford
To email, remove 'me' from my email address
KC6TAY, PP-ASEL
See the Geezer Jeep at
http://members.***.net/jerrypb/
"Bob" <magicclaw@mac.com> wrote in message
news:47b769ae.0312310859.5e46e7c8@posting.google.c om...
> I disagree with this. Yes, if the t-case was kept at the stock height,
> the motor mount lift would help in the driveline angles of the rear
> driveshaft. However, he plans to put a new skid plate on to raise the
> transfer case up. This will effectively negate the potential help that
> raising the engine would have done. Sound right?
>
>
> "Jerry Bransford" <jerrypb@mecox.net> wrote in message
news:<8QiIb.33110$gN.24234@fed1read05>...
> > Your driveshaft length will be fine with that height lift. With a 2"
> > suspension lift, it's common that the transfer case may have to be
dropped a
> > little to eliminate vibrations... but that you're installing a 1.5"
engine
> > lift will eliminate that need. Lifting the engine at the front works
the
> > same as dropping the t-case a little to reduce the angles that can cause
> > drivetrain vibrations. You should be perfectly fine with that
combination.
> >
> > Jerry
> > --
> > Jerry Bransford
> > To email, remove 'me' from my email address
> > KC6TAY, PP-ASEL
> > See the Geezer Jeep at
> > http://members.***.net/jerrypb/
> >
> > "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> > news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > > skidplate. What driveline problems should I expect, what do I need to
> > > buy in advance to fix the problems, how do I fix it, and will I need
> > > to have custom driveshafts made?
> > >
> > > Thanks for your time and help,
> > >
> > > Andrew Whitley
#66
Guest
Posts: n/a
Re: Lift & Driveline problems
Yeah you're right Bob, I did miss that he was also installing a high
clearance skidplate. Though it still may work since he's only installing a
2" suspension lift and the 1.5" engine lift is usually more than enough for
a 3" suspension lift... so it's possible that he may still get away with it.
Jerry
--
Jerry Bransford
To email, remove 'me' from my email address
KC6TAY, PP-ASEL
See the Geezer Jeep at
http://members.***.net/jerrypb/
"Bob" <magicclaw@mac.com> wrote in message
news:47b769ae.0312310859.5e46e7c8@posting.google.c om...
> I disagree with this. Yes, if the t-case was kept at the stock height,
> the motor mount lift would help in the driveline angles of the rear
> driveshaft. However, he plans to put a new skid plate on to raise the
> transfer case up. This will effectively negate the potential help that
> raising the engine would have done. Sound right?
>
>
> "Jerry Bransford" <jerrypb@mecox.net> wrote in message
news:<8QiIb.33110$gN.24234@fed1read05>...
> > Your driveshaft length will be fine with that height lift. With a 2"
> > suspension lift, it's common that the transfer case may have to be
dropped a
> > little to eliminate vibrations... but that you're installing a 1.5"
engine
> > lift will eliminate that need. Lifting the engine at the front works
the
> > same as dropping the t-case a little to reduce the angles that can cause
> > drivetrain vibrations. You should be perfectly fine with that
combination.
> >
> > Jerry
> > --
> > Jerry Bransford
> > To email, remove 'me' from my email address
> > KC6TAY, PP-ASEL
> > See the Geezer Jeep at
> > http://members.***.net/jerrypb/
> >
> > "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> > news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > > skidplate. What driveline problems should I expect, what do I need to
> > > buy in advance to fix the problems, how do I fix it, and will I need
> > > to have custom driveshafts made?
> > >
> > > Thanks for your time and help,
> > >
> > > Andrew Whitley
clearance skidplate. Though it still may work since he's only installing a
2" suspension lift and the 1.5" engine lift is usually more than enough for
a 3" suspension lift... so it's possible that he may still get away with it.
Jerry
--
Jerry Bransford
To email, remove 'me' from my email address
KC6TAY, PP-ASEL
See the Geezer Jeep at
http://members.***.net/jerrypb/
"Bob" <magicclaw@mac.com> wrote in message
news:47b769ae.0312310859.5e46e7c8@posting.google.c om...
> I disagree with this. Yes, if the t-case was kept at the stock height,
> the motor mount lift would help in the driveline angles of the rear
> driveshaft. However, he plans to put a new skid plate on to raise the
> transfer case up. This will effectively negate the potential help that
> raising the engine would have done. Sound right?
>
>
> "Jerry Bransford" <jerrypb@mecox.net> wrote in message
news:<8QiIb.33110$gN.24234@fed1read05>...
> > Your driveshaft length will be fine with that height lift. With a 2"
> > suspension lift, it's common that the transfer case may have to be
dropped a
> > little to eliminate vibrations... but that you're installing a 1.5"
engine
> > lift will eliminate that need. Lifting the engine at the front works
the
> > same as dropping the t-case a little to reduce the angles that can cause
> > drivetrain vibrations. You should be perfectly fine with that
combination.
> >
> > Jerry
> > --
> > Jerry Bransford
> > To email, remove 'me' from my email address
> > KC6TAY, PP-ASEL
> > See the Geezer Jeep at
> > http://members.***.net/jerrypb/
> >
> > "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> > news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > > skidplate. What driveline problems should I expect, what do I need to
> > > buy in advance to fix the problems, how do I fix it, and will I need
> > > to have custom driveshafts made?
> > >
> > > Thanks for your time and help,
> > >
> > > Andrew Whitley
#67
Guest
Posts: n/a
Re: Lift & Driveline problems
Yeah you're right Bob, I did miss that he was also installing a high
clearance skidplate. Though it still may work since he's only installing a
2" suspension lift and the 1.5" engine lift is usually more than enough for
a 3" suspension lift... so it's possible that he may still get away with it.
Jerry
--
Jerry Bransford
To email, remove 'me' from my email address
KC6TAY, PP-ASEL
See the Geezer Jeep at
http://members.***.net/jerrypb/
"Bob" <magicclaw@mac.com> wrote in message
news:47b769ae.0312310859.5e46e7c8@posting.google.c om...
> I disagree with this. Yes, if the t-case was kept at the stock height,
> the motor mount lift would help in the driveline angles of the rear
> driveshaft. However, he plans to put a new skid plate on to raise the
> transfer case up. This will effectively negate the potential help that
> raising the engine would have done. Sound right?
>
>
> "Jerry Bransford" <jerrypb@mecox.net> wrote in message
news:<8QiIb.33110$gN.24234@fed1read05>...
> > Your driveshaft length will be fine with that height lift. With a 2"
> > suspension lift, it's common that the transfer case may have to be
dropped a
> > little to eliminate vibrations... but that you're installing a 1.5"
engine
> > lift will eliminate that need. Lifting the engine at the front works
the
> > same as dropping the t-case a little to reduce the angles that can cause
> > drivetrain vibrations. You should be perfectly fine with that
combination.
> >
> > Jerry
> > --
> > Jerry Bransford
> > To email, remove 'me' from my email address
> > KC6TAY, PP-ASEL
> > See the Geezer Jeep at
> > http://members.***.net/jerrypb/
> >
> > "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> > news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > > skidplate. What driveline problems should I expect, what do I need to
> > > buy in advance to fix the problems, how do I fix it, and will I need
> > > to have custom driveshafts made?
> > >
> > > Thanks for your time and help,
> > >
> > > Andrew Whitley
clearance skidplate. Though it still may work since he's only installing a
2" suspension lift and the 1.5" engine lift is usually more than enough for
a 3" suspension lift... so it's possible that he may still get away with it.
Jerry
--
Jerry Bransford
To email, remove 'me' from my email address
KC6TAY, PP-ASEL
See the Geezer Jeep at
http://members.***.net/jerrypb/
"Bob" <magicclaw@mac.com> wrote in message
news:47b769ae.0312310859.5e46e7c8@posting.google.c om...
> I disagree with this. Yes, if the t-case was kept at the stock height,
> the motor mount lift would help in the driveline angles of the rear
> driveshaft. However, he plans to put a new skid plate on to raise the
> transfer case up. This will effectively negate the potential help that
> raising the engine would have done. Sound right?
>
>
> "Jerry Bransford" <jerrypb@mecox.net> wrote in message
news:<8QiIb.33110$gN.24234@fed1read05>...
> > Your driveshaft length will be fine with that height lift. With a 2"
> > suspension lift, it's common that the transfer case may have to be
dropped a
> > little to eliminate vibrations... but that you're installing a 1.5"
engine
> > lift will eliminate that need. Lifting the engine at the front works
the
> > same as dropping the t-case a little to reduce the angles that can cause
> > drivetrain vibrations. You should be perfectly fine with that
combination.
> >
> > Jerry
> > --
> > Jerry Bransford
> > To email, remove 'me' from my email address
> > KC6TAY, PP-ASEL
> > See the Geezer Jeep at
> > http://members.***.net/jerrypb/
> >
> > "Andrew" <andrewmuaddib@hotmail.com> wrote in message
> > news:8b5c891c.0312300912.1638c86c@posting.google.c om...
> > > I have an 03 TJ Rubicon, and will put in a 2" Old Man Emu suspension
> > > lift and also run 1.5" engine lift (and body) to fit a high clearance
> > > skidplate. What driveline problems should I expect, what do I need to
> > > buy in advance to fix the problems, how do I fix it, and will I need
> > > to have custom driveshafts made?
> > >
> > > Thanks for your time and help,
> > >
> > > Andrew Whitley
#68
Guest
Posts: n/a
Re: Lift & Driveline problems
Hi Matt,
Of course, our Fords have them, as well as all GM utilities and
older Civilian Jeeps. And all of them have the slip joint on the
driveshaft, slip joints on output shafts are use on passenger cars only.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Matt Macchiarolo wrote:
>
> As does my '00 FSM, but as we're talking about rear driveshafts, Bill, you are
> again grasping the irrelevent. Would you believe that every TJ has a CV joint
> in the stock front driveshaft, and NO TJ from the factory has ever had a CV
> joint in the rear.
>
> Picture of a stock rear Rubicon shaft:
> http://www.geocities.com/basscraft.geo/slipjoint.jpg
>
> * * *
> Matt Macchiarolo
> www.townpeddler.com
> www.wolverine4wd.org
> http://wolverine4wd.org/rigs/macchiarolo_ml.html
Of course, our Fords have them, as well as all GM utilities and
older Civilian Jeeps. And all of them have the slip joint on the
driveshaft, slip joints on output shafts are use on passenger cars only.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Matt Macchiarolo wrote:
>
> As does my '00 FSM, but as we're talking about rear driveshafts, Bill, you are
> again grasping the irrelevent. Would you believe that every TJ has a CV joint
> in the stock front driveshaft, and NO TJ from the factory has ever had a CV
> joint in the rear.
>
> Picture of a stock rear Rubicon shaft:
> http://www.geocities.com/basscraft.geo/slipjoint.jpg
>
> * * *
> Matt Macchiarolo
> www.townpeddler.com
> www.wolverine4wd.org
> http://wolverine4wd.org/rigs/macchiarolo_ml.html
#69
Guest
Posts: n/a
Re: Lift & Driveline problems
Hi Matt,
Of course, our Fords have them, as well as all GM utilities and
older Civilian Jeeps. And all of them have the slip joint on the
driveshaft, slip joints on output shafts are use on passenger cars only.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Matt Macchiarolo wrote:
>
> As does my '00 FSM, but as we're talking about rear driveshafts, Bill, you are
> again grasping the irrelevent. Would you believe that every TJ has a CV joint
> in the stock front driveshaft, and NO TJ from the factory has ever had a CV
> joint in the rear.
>
> Picture of a stock rear Rubicon shaft:
> http://www.geocities.com/basscraft.geo/slipjoint.jpg
>
> * * *
> Matt Macchiarolo
> www.townpeddler.com
> www.wolverine4wd.org
> http://wolverine4wd.org/rigs/macchiarolo_ml.html
Of course, our Fords have them, as well as all GM utilities and
older Civilian Jeeps. And all of them have the slip joint on the
driveshaft, slip joints on output shafts are use on passenger cars only.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Matt Macchiarolo wrote:
>
> As does my '00 FSM, but as we're talking about rear driveshafts, Bill, you are
> again grasping the irrelevent. Would you believe that every TJ has a CV joint
> in the stock front driveshaft, and NO TJ from the factory has ever had a CV
> joint in the rear.
>
> Picture of a stock rear Rubicon shaft:
> http://www.geocities.com/basscraft.geo/slipjoint.jpg
>
> * * *
> Matt Macchiarolo
> www.townpeddler.com
> www.wolverine4wd.org
> http://wolverine4wd.org/rigs/macchiarolo_ml.html
#70
Guest
Posts: n/a
Re: Lift & Driveline problems
Hi Matt,
Of course, our Fords have them, as well as all GM utilities and
older Civilian Jeeps. And all of them have the slip joint on the
driveshaft, slip joints on output shafts are use on passenger cars only.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Matt Macchiarolo wrote:
>
> As does my '00 FSM, but as we're talking about rear driveshafts, Bill, you are
> again grasping the irrelevent. Would you believe that every TJ has a CV joint
> in the stock front driveshaft, and NO TJ from the factory has ever had a CV
> joint in the rear.
>
> Picture of a stock rear Rubicon shaft:
> http://www.geocities.com/basscraft.geo/slipjoint.jpg
>
> * * *
> Matt Macchiarolo
> www.townpeddler.com
> www.wolverine4wd.org
> http://wolverine4wd.org/rigs/macchiarolo_ml.html
Of course, our Fords have them, as well as all GM utilities and
older Civilian Jeeps. And all of them have the slip joint on the
driveshaft, slip joints on output shafts are use on passenger cars only.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Matt Macchiarolo wrote:
>
> As does my '00 FSM, but as we're talking about rear driveshafts, Bill, you are
> again grasping the irrelevent. Would you believe that every TJ has a CV joint
> in the stock front driveshaft, and NO TJ from the factory has ever had a CV
> joint in the rear.
>
> Picture of a stock rear Rubicon shaft:
> http://www.geocities.com/basscraft.geo/slipjoint.jpg
>
> * * *
> Matt Macchiarolo
> www.townpeddler.com
> www.wolverine4wd.org
> http://wolverine4wd.org/rigs/macchiarolo_ml.html