Just did the Nutter
10-11-2003, 05:58 PM
#1
Guest
Posts: n/a
Just did the Nutter
Hey all,
'85 CJ7/258/BBD
I just passed the emissions test so I thought I'd go ahead and put the
computer to sleep. It's great not hearing those stupid air valves sputtering
away and messing up the idle. I was amazed the thing fired right up! I took
a really quick test drive expecting a bunch of 'seat-o-the-pants'
improvement but it seems about as spongy on acceleration as it did before. I
think I might have goofed a bit by not tweaking the mix screws lean before
unplugging the computer. I just spun them out to 5 turns and hoped for the
best. Are the metering pins likely still in the way? I did the 1/4 turn lean
routine Mike R talked about in some posts from August and backed them out
1/4 turn when the engine started stumbling. Idle is smooth. Before messing
with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
disconnected at the distributor. Correct or no? I'm getting some ping on
acceleration but cruising is OK. Didn't take it out on the Highway yet to
see if I can go faster than the 65-70mph I'd see with the computer in the
loop. I'm going to futz with it more tomorrow but I'm losing light right now
so...
'85 CJ7/258/BBD
I just passed the emissions test so I thought I'd go ahead and put the
computer to sleep. It's great not hearing those stupid air valves sputtering
away and messing up the idle. I was amazed the thing fired right up! I took
a really quick test drive expecting a bunch of 'seat-o-the-pants'
improvement but it seems about as spongy on acceleration as it did before. I
think I might have goofed a bit by not tweaking the mix screws lean before
unplugging the computer. I just spun them out to 5 turns and hoped for the
best. Are the metering pins likely still in the way? I did the 1/4 turn lean
routine Mike R talked about in some posts from August and backed them out
1/4 turn when the engine started stumbling. Idle is smooth. Before messing
with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
disconnected at the distributor. Correct or no? I'm getting some ping on
acceleration but cruising is OK. Didn't take it out on the Highway yet to
see if I can go faster than the 65-70mph I'd see with the computer in the
loop. I'm going to futz with it more tomorrow but I'm losing light right now
so...
10-11-2003, 06:12 PM
#2
Guest
Posts: n/a
Re: Just did the Nutter
err. 800 RPM. sheesh
> From: KurtS <nospam@thanksImFull.spam>
> Newsgroups: rec.autos.makers.jeep+******
> Date: Sat, 11 Oct 2003 17:58:56 -0400
> Subject: Just did the Nutter
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
>
> From: KurtS <nospam@thanksImFull.spam>
> Newsgroups: rec.autos.makers.jeep+******
> Date: Sat, 11 Oct 2003 17:58:56 -0400
> Subject: Just did the Nutter
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
>
10-11-2003, 06:12 PM
#3
Guest
Posts: n/a
Re: Just did the Nutter
err. 800 RPM. sheesh
> From: KurtS <nospam@thanksImFull.spam>
> Newsgroups: rec.autos.makers.jeep+******
> Date: Sat, 11 Oct 2003 17:58:56 -0400
> Subject: Just did the Nutter
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
>
> From: KurtS <nospam@thanksImFull.spam>
> Newsgroups: rec.autos.makers.jeep+******
> Date: Sat, 11 Oct 2003 17:58:56 -0400
> Subject: Just did the Nutter
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
>
10-11-2003, 06:12 PM
#4
Guest
Posts: n/a
Re: Just did the Nutter
err. 800 RPM. sheesh
> From: KurtS <nospam@thanksImFull.spam>
> Newsgroups: rec.autos.makers.jeep+******
> Date: Sat, 11 Oct 2003 17:58:56 -0400
> Subject: Just did the Nutter
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
>
> From: KurtS <nospam@thanksImFull.spam>
> Newsgroups: rec.autos.makers.jeep+******
> Date: Sat, 11 Oct 2003 17:58:56 -0400
> Subject: Just did the Nutter
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
>
10-12-2003, 09:59 AM
#5
Guest
Posts: n/a
Re: Just did the Nutter
Your timing can be anywhere between 6 to 12 depending on your engine. I
use my ear to tweak the timing once the carb is set up. I set the
timing at say 9 deg, then get the carb running smooth then turn the
distributor slightly either direction to get the smoothest purr. Mine
set at 9, but others I have done varied from 8 to 10 or 11.
A vacuum gauge is helpful too. The best timing will usually be really
close to the highest vacuum reading..
I find I get the best acceleration using a ported vacuum advance. I
also get the best power using high octane. If I am running her loaded
full and hard, I look for 91 or 92. If I am running easy I have used
mid range 89 and it didn't ping.
For me gas mileage tells all. On a long highway run, I get 19 US mpg or
350 miles per tank on 91 octane. Drop to 87 octane and drop to 250
miles per tank.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
KurtS wrote:
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
use my ear to tweak the timing once the carb is set up. I set the
timing at say 9 deg, then get the carb running smooth then turn the
distributor slightly either direction to get the smoothest purr. Mine
set at 9, but others I have done varied from 8 to 10 or 11.
A vacuum gauge is helpful too. The best timing will usually be really
close to the highest vacuum reading..
I find I get the best acceleration using a ported vacuum advance. I
also get the best power using high octane. If I am running her loaded
full and hard, I look for 91 or 92. If I am running easy I have used
mid range 89 and it didn't ping.
For me gas mileage tells all. On a long highway run, I get 19 US mpg or
350 miles per tank on 91 octane. Drop to 87 octane and drop to 250
miles per tank.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
KurtS wrote:
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
10-12-2003, 09:59 AM
#6
Guest
Posts: n/a
Re: Just did the Nutter
Your timing can be anywhere between 6 to 12 depending on your engine. I
use my ear to tweak the timing once the carb is set up. I set the
timing at say 9 deg, then get the carb running smooth then turn the
distributor slightly either direction to get the smoothest purr. Mine
set at 9, but others I have done varied from 8 to 10 or 11.
A vacuum gauge is helpful too. The best timing will usually be really
close to the highest vacuum reading..
I find I get the best acceleration using a ported vacuum advance. I
also get the best power using high octane. If I am running her loaded
full and hard, I look for 91 or 92. If I am running easy I have used
mid range 89 and it didn't ping.
For me gas mileage tells all. On a long highway run, I get 19 US mpg or
350 miles per tank on 91 octane. Drop to 87 octane and drop to 250
miles per tank.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
KurtS wrote:
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
use my ear to tweak the timing once the carb is set up. I set the
timing at say 9 deg, then get the carb running smooth then turn the
distributor slightly either direction to get the smoothest purr. Mine
set at 9, but others I have done varied from 8 to 10 or 11.
A vacuum gauge is helpful too. The best timing will usually be really
close to the highest vacuum reading..
I find I get the best acceleration using a ported vacuum advance. I
also get the best power using high octane. If I am running her loaded
full and hard, I look for 91 or 92. If I am running easy I have used
mid range 89 and it didn't ping.
For me gas mileage tells all. On a long highway run, I get 19 US mpg or
350 miles per tank on 91 octane. Drop to 87 octane and drop to 250
miles per tank.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
KurtS wrote:
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
10-12-2003, 09:59 AM
#7
Guest
Posts: n/a
Re: Just did the Nutter
Your timing can be anywhere between 6 to 12 depending on your engine. I
use my ear to tweak the timing once the carb is set up. I set the
timing at say 9 deg, then get the carb running smooth then turn the
distributor slightly either direction to get the smoothest purr. Mine
set at 9, but others I have done varied from 8 to 10 or 11.
A vacuum gauge is helpful too. The best timing will usually be really
close to the highest vacuum reading..
I find I get the best acceleration using a ported vacuum advance. I
also get the best power using high octane. If I am running her loaded
full and hard, I look for 91 or 92. If I am running easy I have used
mid range 89 and it didn't ping.
For me gas mileage tells all. On a long highway run, I get 19 US mpg or
350 miles per tank on 91 octane. Drop to 87 octane and drop to 250
miles per tank.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
KurtS wrote:
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
use my ear to tweak the timing once the carb is set up. I set the
timing at say 9 deg, then get the carb running smooth then turn the
distributor slightly either direction to get the smoothest purr. Mine
set at 9, but others I have done varied from 8 to 10 or 11.
A vacuum gauge is helpful too. The best timing will usually be really
close to the highest vacuum reading..
I find I get the best acceleration using a ported vacuum advance. I
also get the best power using high octane. If I am running her loaded
full and hard, I look for 91 or 92. If I am running easy I have used
mid range 89 and it didn't ping.
For me gas mileage tells all. On a long highway run, I get 19 US mpg or
350 miles per tank on 91 octane. Drop to 87 octane and drop to 250
miles per tank.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
KurtS wrote:
>
> Hey all,
>
> '85 CJ7/258/BBD
>
> I just passed the emissions test so I thought I'd go ahead and put the
> computer to sleep. It's great not hearing those stupid air valves sputtering
> away and messing up the idle. I was amazed the thing fired right up! I took
> a really quick test drive expecting a bunch of 'seat-o-the-pants'
> improvement but it seems about as spongy on acceleration as it did before. I
> think I might have goofed a bit by not tweaking the mix screws lean before
> unplugging the computer. I just spun them out to 5 turns and hoped for the
> best. Are the metering pins likely still in the way? I did the 1/4 turn lean
> routine Mike R talked about in some posts from August and backed them out
> 1/4 turn when the engine started stumbling. Idle is smooth. Before messing
> with the mix, I set the timing at 9 deg BTDC at 800 RMP and the vacuum
> disconnected at the distributor. Correct or no? I'm getting some ping on
> acceleration but cruising is OK. Didn't take it out on the Highway yet to
> see if I can go faster than the 65-70mph I'd see with the computer in the
> loop. I'm going to futz with it more tomorrow but I'm losing light right now
> so...
Thread
Thread Starter
Forum
Replies
Last Post
Alouf Zen
Jeep Mailing List
9
09-28-2004 02:22 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)