Jeep transmission filter/fluid change
02-05-2005, 01:19 PM
#1
Guest
Posts: n/a
Jeep transmission filter/fluid change
I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
intent on doing a transmission filter and fluid change myself but have
hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
I was under the car, I noticed a metal pipe connected to the side of the
pan and was uncertain as how to disconnect/re-connect it in the course
of the fluid/filter change. I consulted two repair manuals. The Haynes
Manual doesn¹t even refer to it when it describes how to do the fluid
change while the Chilton manual just briefly states, to disconnect the
pick-up pipe, if so equipped. I noticed that at the point of entry into
the transmission pan, the pipe appears to be attached by a metal flange,
and it is not obvious to me how it will detach from the pan body.
Therefore I have two questions.
One---How is the pipe connected/detached from the pan?
Two---there must be some kind of gasket/washer to ensure a leak proof
seal between the pipe and pan, so does the transmission filter and
gasket kit sold at auto parts stores normally include a gasket/seal for
the pipe?
Thanks to any who can enlighten me.
Sincerely,
Confused in Las Vegas
intent on doing a transmission filter and fluid change myself but have
hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
I was under the car, I noticed a metal pipe connected to the side of the
pan and was uncertain as how to disconnect/re-connect it in the course
of the fluid/filter change. I consulted two repair manuals. The Haynes
Manual doesn¹t even refer to it when it describes how to do the fluid
change while the Chilton manual just briefly states, to disconnect the
pick-up pipe, if so equipped. I noticed that at the point of entry into
the transmission pan, the pipe appears to be attached by a metal flange,
and it is not obvious to me how it will detach from the pan body.
Therefore I have two questions.
One---How is the pipe connected/detached from the pan?
Two---there must be some kind of gasket/washer to ensure a leak proof
seal between the pipe and pan, so does the transmission filter and
gasket kit sold at auto parts stores normally include a gasket/seal for
the pipe?
Thanks to any who can enlighten me.
Sincerely,
Confused in Las Vegas
02-05-2005, 03:18 PM
#2
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Hi Eve,
For some reason I'll never understand, Chrysler does put a drain
plug on their torque converter, like Ford and GM and the whole rest of
the world does. Forcing you to take to the shop that have the special
flush equipment.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Eve Howard wrote:
>
> I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
> intent on doing a transmission filter and fluid change myself but have
> hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
> I was under the car, I noticed a metal pipe connected to the side of the
> pan and was uncertain as how to disconnect/re-connect it in the course
> of the fluid/filter change. I consulted two repair manuals. The Haynes
> Manual doesn¹t even refer to it when it describes how to do the fluid
> change while the Chilton manual just briefly states, to disconnect the
> pick-up pipe, if so equipped. I noticed that at the point of entry into
> the transmission pan, the pipe appears to be attached by a metal flange,
> and it is not obvious to me how it will detach from the pan body.
> Therefore I have two questions.
>
> One---How is the pipe connected/detached from the pan?
>
> Two---there must be some kind of gasket/washer to ensure a leak proof
> seal between the pipe and pan, so does the transmission filter and
> gasket kit sold at auto parts stores normally include a gasket/seal for
> the pipe?
>
> Thanks to any who can enlighten me.
>
> Sincerely,
> Confused in Las Vegas
For some reason I'll never understand, Chrysler does put a drain
plug on their torque converter, like Ford and GM and the whole rest of
the world does. Forcing you to take to the shop that have the special
flush equipment.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Eve Howard wrote:
>
> I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
> intent on doing a transmission filter and fluid change myself but have
> hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
> I was under the car, I noticed a metal pipe connected to the side of the
> pan and was uncertain as how to disconnect/re-connect it in the course
> of the fluid/filter change. I consulted two repair manuals. The Haynes
> Manual doesn¹t even refer to it when it describes how to do the fluid
> change while the Chilton manual just briefly states, to disconnect the
> pick-up pipe, if so equipped. I noticed that at the point of entry into
> the transmission pan, the pipe appears to be attached by a metal flange,
> and it is not obvious to me how it will detach from the pan body.
> Therefore I have two questions.
>
> One---How is the pipe connected/detached from the pan?
>
> Two---there must be some kind of gasket/washer to ensure a leak proof
> seal between the pipe and pan, so does the transmission filter and
> gasket kit sold at auto parts stores normally include a gasket/seal for
> the pipe?
>
> Thanks to any who can enlighten me.
>
> Sincerely,
> Confused in Las Vegas
02-05-2005, 03:18 PM
#3
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Hi Eve,
For some reason I'll never understand, Chrysler does put a drain
plug on their torque converter, like Ford and GM and the whole rest of
the world does. Forcing you to take to the shop that have the special
flush equipment.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Eve Howard wrote:
>
> I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
> intent on doing a transmission filter and fluid change myself but have
> hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
> I was under the car, I noticed a metal pipe connected to the side of the
> pan and was uncertain as how to disconnect/re-connect it in the course
> of the fluid/filter change. I consulted two repair manuals. The Haynes
> Manual doesn¹t even refer to it when it describes how to do the fluid
> change while the Chilton manual just briefly states, to disconnect the
> pick-up pipe, if so equipped. I noticed that at the point of entry into
> the transmission pan, the pipe appears to be attached by a metal flange,
> and it is not obvious to me how it will detach from the pan body.
> Therefore I have two questions.
>
> One---How is the pipe connected/detached from the pan?
>
> Two---there must be some kind of gasket/washer to ensure a leak proof
> seal between the pipe and pan, so does the transmission filter and
> gasket kit sold at auto parts stores normally include a gasket/seal for
> the pipe?
>
> Thanks to any who can enlighten me.
>
> Sincerely,
> Confused in Las Vegas
For some reason I'll never understand, Chrysler does put a drain
plug on their torque converter, like Ford and GM and the whole rest of
the world does. Forcing you to take to the shop that have the special
flush equipment.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Eve Howard wrote:
>
> I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
> intent on doing a transmission filter and fluid change myself but have
> hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
> I was under the car, I noticed a metal pipe connected to the side of the
> pan and was uncertain as how to disconnect/re-connect it in the course
> of the fluid/filter change. I consulted two repair manuals. The Haynes
> Manual doesn¹t even refer to it when it describes how to do the fluid
> change while the Chilton manual just briefly states, to disconnect the
> pick-up pipe, if so equipped. I noticed that at the point of entry into
> the transmission pan, the pipe appears to be attached by a metal flange,
> and it is not obvious to me how it will detach from the pan body.
> Therefore I have two questions.
>
> One---How is the pipe connected/detached from the pan?
>
> Two---there must be some kind of gasket/washer to ensure a leak proof
> seal between the pipe and pan, so does the transmission filter and
> gasket kit sold at auto parts stores normally include a gasket/seal for
> the pipe?
>
> Thanks to any who can enlighten me.
>
> Sincerely,
> Confused in Las Vegas
02-05-2005, 03:18 PM
#4
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Hi Eve,
For some reason I'll never understand, Chrysler does put a drain
plug on their torque converter, like Ford and GM and the whole rest of
the world does. Forcing you to take to the shop that have the special
flush equipment.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Eve Howard wrote:
>
> I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
> intent on doing a transmission filter and fluid change myself but have
> hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
> I was under the car, I noticed a metal pipe connected to the side of the
> pan and was uncertain as how to disconnect/re-connect it in the course
> of the fluid/filter change. I consulted two repair manuals. The Haynes
> Manual doesn¹t even refer to it when it describes how to do the fluid
> change while the Chilton manual just briefly states, to disconnect the
> pick-up pipe, if so equipped. I noticed that at the point of entry into
> the transmission pan, the pipe appears to be attached by a metal flange,
> and it is not obvious to me how it will detach from the pan body.
> Therefore I have two questions.
>
> One---How is the pipe connected/detached from the pan?
>
> Two---there must be some kind of gasket/washer to ensure a leak proof
> seal between the pipe and pan, so does the transmission filter and
> gasket kit sold at auto parts stores normally include a gasket/seal for
> the pipe?
>
> Thanks to any who can enlighten me.
>
> Sincerely,
> Confused in Las Vegas
For some reason I'll never understand, Chrysler does put a drain
plug on their torque converter, like Ford and GM and the whole rest of
the world does. Forcing you to take to the shop that have the special
flush equipment.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Eve Howard wrote:
>
> I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
> intent on doing a transmission filter and fluid change myself but have
> hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
> I was under the car, I noticed a metal pipe connected to the side of the
> pan and was uncertain as how to disconnect/re-connect it in the course
> of the fluid/filter change. I consulted two repair manuals. The Haynes
> Manual doesn¹t even refer to it when it describes how to do the fluid
> change while the Chilton manual just briefly states, to disconnect the
> pick-up pipe, if so equipped. I noticed that at the point of entry into
> the transmission pan, the pipe appears to be attached by a metal flange,
> and it is not obvious to me how it will detach from the pan body.
> Therefore I have two questions.
>
> One---How is the pipe connected/detached from the pan?
>
> Two---there must be some kind of gasket/washer to ensure a leak proof
> seal between the pipe and pan, so does the transmission filter and
> gasket kit sold at auto parts stores normally include a gasket/seal for
> the pipe?
>
> Thanks to any who can enlighten me.
>
> Sincerely,
> Confused in Las Vegas
02-05-2005, 03:20 PM
#5
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Doesn't have a drain plug.
"L.W.(ßill) ------ III" wrote:
>
> Hi Eve,
> For some reason I'll never understand, Chrysler does put a drain
> plug on their torque converter, like Ford and GM and the whole rest of
> the world does. Forcing you to take to the shop that have the special
> flush equipment.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
"L.W.(ßill) ------ III" wrote:
>
> Hi Eve,
> For some reason I'll never understand, Chrysler does put a drain
> plug on their torque converter, like Ford and GM and the whole rest of
> the world does. Forcing you to take to the shop that have the special
> flush equipment.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
02-05-2005, 03:20 PM
#6
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Doesn't have a drain plug.
"L.W.(ßill) ------ III" wrote:
>
> Hi Eve,
> For some reason I'll never understand, Chrysler does put a drain
> plug on their torque converter, like Ford and GM and the whole rest of
> the world does. Forcing you to take to the shop that have the special
> flush equipment.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
"L.W.(ßill) ------ III" wrote:
>
> Hi Eve,
> For some reason I'll never understand, Chrysler does put a drain
> plug on their torque converter, like Ford and GM and the whole rest of
> the world does. Forcing you to take to the shop that have the special
> flush equipment.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
02-05-2005, 03:20 PM
#7
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Doesn't have a drain plug.
"L.W.(ßill) ------ III" wrote:
>
> Hi Eve,
> For some reason I'll never understand, Chrysler does put a drain
> plug on their torque converter, like Ford and GM and the whole rest of
> the world does. Forcing you to take to the shop that have the special
> flush equipment.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
"L.W.(ßill) ------ III" wrote:
>
> Hi Eve,
> For some reason I'll never understand, Chrysler does put a drain
> plug on their torque converter, like Ford and GM and the whole rest of
> the world does. Forcing you to take to the shop that have the special
> flush equipment.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
02-05-2005, 05:39 PM
#8
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Hi Eve,
I have a 1987 Cherokee with an AW-4 transmission. On my transmission
the tube connected to the side of the pan is the fill tube. This tube
is made of two parts. The lower part is permanently mounted to the
pan. The upper part of the fill tube has an O-ring on the end and it
slides into the lower part. You have to loosen the bracket that holds
the upper part and then pull it out. You can then unbolt the pan and
remove it.
Mike Capel
capel AT mb DOT sympatico DOT ca
On Sat, 05 Feb 2005 10:19:07 -0800, Eve Howard <eve@shadowlane.com>
wrote:
>I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
>intent on doing a transmission filter and fluid change myself but have
>hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
>I was under the car, I noticed a metal pipe connected to the side of the
>pan and was uncertain as how to disconnect/re-connect it in the course
>of the fluid/filter change. I consulted two repair manuals. The Haynes
>Manual doesn¹t even refer to it when it describes how to do the fluid
>change while the Chilton manual just briefly states, to disconnect the
>pick-up pipe, if so equipped. I noticed that at the point of entry into
>the transmission pan, the pipe appears to be attached by a metal flange,
>and it is not obvious to me how it will detach from the pan body.
>Therefore I have two questions.
>
>One---How is the pipe connected/detached from the pan?
>
>Two---there must be some kind of gasket/washer to ensure a leak proof
>seal between the pipe and pan, so does the transmission filter and
>gasket kit sold at auto parts stores normally include a gasket/seal for
>the pipe?
>
>Thanks to any who can enlighten me.
>
>Sincerely,
>Confused in Las Vegas
I have a 1987 Cherokee with an AW-4 transmission. On my transmission
the tube connected to the side of the pan is the fill tube. This tube
is made of two parts. The lower part is permanently mounted to the
pan. The upper part of the fill tube has an O-ring on the end and it
slides into the lower part. You have to loosen the bracket that holds
the upper part and then pull it out. You can then unbolt the pan and
remove it.
Mike Capel
capel AT mb DOT sympatico DOT ca
On Sat, 05 Feb 2005 10:19:07 -0800, Eve Howard <eve@shadowlane.com>
wrote:
>I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
>intent on doing a transmission filter and fluid change myself but have
>hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
>I was under the car, I noticed a metal pipe connected to the side of the
>pan and was uncertain as how to disconnect/re-connect it in the course
>of the fluid/filter change. I consulted two repair manuals. The Haynes
>Manual doesn¹t even refer to it when it describes how to do the fluid
>change while the Chilton manual just briefly states, to disconnect the
>pick-up pipe, if so equipped. I noticed that at the point of entry into
>the transmission pan, the pipe appears to be attached by a metal flange,
>and it is not obvious to me how it will detach from the pan body.
>Therefore I have two questions.
>
>One---How is the pipe connected/detached from the pan?
>
>Two---there must be some kind of gasket/washer to ensure a leak proof
>seal between the pipe and pan, so does the transmission filter and
>gasket kit sold at auto parts stores normally include a gasket/seal for
>the pipe?
>
>Thanks to any who can enlighten me.
>
>Sincerely,
>Confused in Las Vegas
02-05-2005, 05:39 PM
#9
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Hi Eve,
I have a 1987 Cherokee with an AW-4 transmission. On my transmission
the tube connected to the side of the pan is the fill tube. This tube
is made of two parts. The lower part is permanently mounted to the
pan. The upper part of the fill tube has an O-ring on the end and it
slides into the lower part. You have to loosen the bracket that holds
the upper part and then pull it out. You can then unbolt the pan and
remove it.
Mike Capel
capel AT mb DOT sympatico DOT ca
On Sat, 05 Feb 2005 10:19:07 -0800, Eve Howard <eve@shadowlane.com>
wrote:
>I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
>intent on doing a transmission filter and fluid change myself but have
>hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
>I was under the car, I noticed a metal pipe connected to the side of the
>pan and was uncertain as how to disconnect/re-connect it in the course
>of the fluid/filter change. I consulted two repair manuals. The Haynes
>Manual doesn¹t even refer to it when it describes how to do the fluid
>change while the Chilton manual just briefly states, to disconnect the
>pick-up pipe, if so equipped. I noticed that at the point of entry into
>the transmission pan, the pipe appears to be attached by a metal flange,
>and it is not obvious to me how it will detach from the pan body.
>Therefore I have two questions.
>
>One---How is the pipe connected/detached from the pan?
>
>Two---there must be some kind of gasket/washer to ensure a leak proof
>seal between the pipe and pan, so does the transmission filter and
>gasket kit sold at auto parts stores normally include a gasket/seal for
>the pipe?
>
>Thanks to any who can enlighten me.
>
>Sincerely,
>Confused in Las Vegas
I have a 1987 Cherokee with an AW-4 transmission. On my transmission
the tube connected to the side of the pan is the fill tube. This tube
is made of two parts. The lower part is permanently mounted to the
pan. The upper part of the fill tube has an O-ring on the end and it
slides into the lower part. You have to loosen the bracket that holds
the upper part and then pull it out. You can then unbolt the pan and
remove it.
Mike Capel
capel AT mb DOT sympatico DOT ca
On Sat, 05 Feb 2005 10:19:07 -0800, Eve Howard <eve@shadowlane.com>
wrote:
>I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
>intent on doing a transmission filter and fluid change myself but have
>hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
>I was under the car, I noticed a metal pipe connected to the side of the
>pan and was uncertain as how to disconnect/re-connect it in the course
>of the fluid/filter change. I consulted two repair manuals. The Haynes
>Manual doesn¹t even refer to it when it describes how to do the fluid
>change while the Chilton manual just briefly states, to disconnect the
>pick-up pipe, if so equipped. I noticed that at the point of entry into
>the transmission pan, the pipe appears to be attached by a metal flange,
>and it is not obvious to me how it will detach from the pan body.
>Therefore I have two questions.
>
>One---How is the pipe connected/detached from the pan?
>
>Two---there must be some kind of gasket/washer to ensure a leak proof
>seal between the pipe and pan, so does the transmission filter and
>gasket kit sold at auto parts stores normally include a gasket/seal for
>the pipe?
>
>Thanks to any who can enlighten me.
>
>Sincerely,
>Confused in Las Vegas
02-05-2005, 05:39 PM
#10
Guest
Posts: n/a
Re: Jeep transmission filter/fluid change
Hi Eve,
I have a 1987 Cherokee with an AW-4 transmission. On my transmission
the tube connected to the side of the pan is the fill tube. This tube
is made of two parts. The lower part is permanently mounted to the
pan. The upper part of the fill tube has an O-ring on the end and it
slides into the lower part. You have to loosen the bracket that holds
the upper part and then pull it out. You can then unbolt the pan and
remove it.
Mike Capel
capel AT mb DOT sympatico DOT ca
On Sat, 05 Feb 2005 10:19:07 -0800, Eve Howard <eve@shadowlane.com>
wrote:
>I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
>intent on doing a transmission filter and fluid change myself but have
>hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
>I was under the car, I noticed a metal pipe connected to the side of the
>pan and was uncertain as how to disconnect/re-connect it in the course
>of the fluid/filter change. I consulted two repair manuals. The Haynes
>Manual doesn¹t even refer to it when it describes how to do the fluid
>change while the Chilton manual just briefly states, to disconnect the
>pick-up pipe, if so equipped. I noticed that at the point of entry into
>the transmission pan, the pipe appears to be attached by a metal flange,
>and it is not obvious to me how it will detach from the pan body.
>Therefore I have two questions.
>
>One---How is the pipe connected/detached from the pan?
>
>Two---there must be some kind of gasket/washer to ensure a leak proof
>seal between the pipe and pan, so does the transmission filter and
>gasket kit sold at auto parts stores normally include a gasket/seal for
>the pipe?
>
>Thanks to any who can enlighten me.
>
>Sincerely,
>Confused in Las Vegas
I have a 1987 Cherokee with an AW-4 transmission. On my transmission
the tube connected to the side of the pan is the fill tube. This tube
is made of two parts. The lower part is permanently mounted to the
pan. The upper part of the fill tube has an O-ring on the end and it
slides into the lower part. You have to loosen the bracket that holds
the upper part and then pull it out. You can then unbolt the pan and
remove it.
Mike Capel
capel AT mb DOT sympatico DOT ca
On Sat, 05 Feb 2005 10:19:07 -0800, Eve Howard <eve@shadowlane.com>
wrote:
>I am the proud owner of a 1997 Jeep Cherokee Sport 4 wheel drive. I am
>intent on doing a transmission filter and fluid change myself but have
>hit a bump in the road. The tranny is an AW-4 (automatic 4-speed). While
>I was under the car, I noticed a metal pipe connected to the side of the
>pan and was uncertain as how to disconnect/re-connect it in the course
>of the fluid/filter change. I consulted two repair manuals. The Haynes
>Manual doesn¹t even refer to it when it describes how to do the fluid
>change while the Chilton manual just briefly states, to disconnect the
>pick-up pipe, if so equipped. I noticed that at the point of entry into
>the transmission pan, the pipe appears to be attached by a metal flange,
>and it is not obvious to me how it will detach from the pan body.
>Therefore I have two questions.
>
>One---How is the pipe connected/detached from the pan?
>
>Two---there must be some kind of gasket/washer to ensure a leak proof
>seal between the pipe and pan, so does the transmission filter and
>gasket kit sold at auto parts stores normally include a gasket/seal for
>the pipe?
>
>Thanks to any who can enlighten me.
>
>Sincerely,
>Confused in Las Vegas