Jeep Liberty Fog Lights
#11
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 11:05:45 -0400, "billy ray"
<billy_ray@SPAMfuse.net> wrote:
>
>You can wire the relay so that they only come on with the low beams. Use
>the hot wire to the low beam light to power the relay.
>
I've thought about that as a possibility but if there is an unused
Foglight terminal lying aorund it would be much better to use
that.since the Foglight switch on the column stalk operates the rear
fogs, I presume that it is also wired to run the front fogs - I just
need to find the pick up point - if it exists.
If all else fails I'll go for the dipped beam as the feed for the
relay.
Thanks
Ewan Scott
<billy_ray@SPAMfuse.net> wrote:
>
>You can wire the relay so that they only come on with the low beams. Use
>the hot wire to the low beam light to power the relay.
>
I've thought about that as a possibility but if there is an unused
Foglight terminal lying aorund it would be much better to use
that.since the Foglight switch on the column stalk operates the rear
fogs, I presume that it is also wired to run the front fogs - I just
need to find the pick up point - if it exists.
If all else fails I'll go for the dipped beam as the feed for the
relay.
Thanks
Ewan Scott
#12
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 11:05:45 -0400, "billy ray"
<billy_ray@SPAMfuse.net> wrote:
>
>You can wire the relay so that they only come on with the low beams. Use
>the hot wire to the low beam light to power the relay.
>
I've thought about that as a possibility but if there is an unused
Foglight terminal lying aorund it would be much better to use
that.since the Foglight switch on the column stalk operates the rear
fogs, I presume that it is also wired to run the front fogs - I just
need to find the pick up point - if it exists.
If all else fails I'll go for the dipped beam as the feed for the
relay.
Thanks
Ewan Scott
<billy_ray@SPAMfuse.net> wrote:
>
>You can wire the relay so that they only come on with the low beams. Use
>the hot wire to the low beam light to power the relay.
>
I've thought about that as a possibility but if there is an unused
Foglight terminal lying aorund it would be much better to use
that.since the Foglight switch on the column stalk operates the rear
fogs, I presume that it is also wired to run the front fogs - I just
need to find the pick up point - if it exists.
If all else fails I'll go for the dipped beam as the feed for the
relay.
Thanks
Ewan Scott
#13
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 11:05:45 -0400, "billy ray"
<billy_ray@SPAMfuse.net> wrote:
>
>You can wire the relay so that they only come on with the low beams. Use
>the hot wire to the low beam light to power the relay.
>
I've thought about that as a possibility but if there is an unused
Foglight terminal lying aorund it would be much better to use
that.since the Foglight switch on the column stalk operates the rear
fogs, I presume that it is also wired to run the front fogs - I just
need to find the pick up point - if it exists.
If all else fails I'll go for the dipped beam as the feed for the
relay.
Thanks
Ewan Scott
<billy_ray@SPAMfuse.net> wrote:
>
>You can wire the relay so that they only come on with the low beams. Use
>the hot wire to the low beam light to power the relay.
>
I've thought about that as a possibility but if there is an unused
Foglight terminal lying aorund it would be much better to use
that.since the Foglight switch on the column stalk operates the rear
fogs, I presume that it is also wired to run the front fogs - I just
need to find the pick up point - if it exists.
If all else fails I'll go for the dipped beam as the feed for the
relay.
Thanks
Ewan Scott
#14
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 10:18:22 -0500, "Kate" <Kate@dub.dub.dub.com
(please ask)> wrote:
>Whent hey installed the renegade lights on my Liberty, they drilled a hole
>in the firewall.
>Do you not have the instructions or are they some aftermarlet that isn't OEM
>?
Instructions? The company that I got the lights from realised that
no-one reads instructions till something goes wrong. So to save money
on the package they don't publish any fitting instructions :-)
>There were a lot of things about the install that made me just take it in
>and have it done.
>I was glad I did, that way if I had a meltdown, it was covered.
>
That's a fair point. I would have fitted Jeep OEM fogs but.... they
cost about $175 plus carriage, and tax this end. So from the US they
cost me about $200.
If I buy the same lights here they cost about £180, go figure.
So, I buy cheaper aftermarket lights and mount them myself - I've had
them working off the battery, shipped from the US at £48, a quarter of
the price of a UK bought set.
As for having them fitted professionally, well, it's a Jeep and if I
went to the local Jeep Dealer to have them fitted I'd be looking at a
workshop rate of anything between £50 and £90 per hour.
I'm reluctant to drill a hole in the firewayy because - A/ I don't
know what's on the other side, and B/ Even if I wanted to I'd have to
remove too much gubbins from either side to get a drill in to do the
job.
If I go anywhere else, there is a very good chance that they won't
know any more than I do because there aren't THAT many Liberty's
about, a few, but not that many.
Ewan Scott
>
>
>"Ewan Scott" <ewanscott@btinternet.com> wrote in message
>news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
>: Okay, I've got the aftermarket foglights wired anf they would work if
>: I connected them up direct to the battery - but I'd like to be legal
>: and wire them to work on dipped beam. I'm told that there is a harness
>: socket for the OEM foglights and that it is somewhere on the left side
>: front wing/ fender.
>:
>: I've searched but can't find any unused terminal blocks. Just in case
>: it is reversed for the RHD model I've checked on the right hand side
>: but still no joy.
>:
>: Can anyone tell me where to find it - if it exists?
>:
>: Also, where have people fed accessory cables throught he firewall? I'm
>: looking at the left hand side where the main harness comes through,
>: but something keeps blocking any feed I put through.
>:
>: I don't want to drill any more holes, so any guidance would be
>: welcome.
>:
>: Ewan Scott
>
(please ask)> wrote:
>Whent hey installed the renegade lights on my Liberty, they drilled a hole
>in the firewall.
>Do you not have the instructions or are they some aftermarlet that isn't OEM
>?
Instructions? The company that I got the lights from realised that
no-one reads instructions till something goes wrong. So to save money
on the package they don't publish any fitting instructions :-)
>There were a lot of things about the install that made me just take it in
>and have it done.
>I was glad I did, that way if I had a meltdown, it was covered.
>
That's a fair point. I would have fitted Jeep OEM fogs but.... they
cost about $175 plus carriage, and tax this end. So from the US they
cost me about $200.
If I buy the same lights here they cost about £180, go figure.
So, I buy cheaper aftermarket lights and mount them myself - I've had
them working off the battery, shipped from the US at £48, a quarter of
the price of a UK bought set.
As for having them fitted professionally, well, it's a Jeep and if I
went to the local Jeep Dealer to have them fitted I'd be looking at a
workshop rate of anything between £50 and £90 per hour.
I'm reluctant to drill a hole in the firewayy because - A/ I don't
know what's on the other side, and B/ Even if I wanted to I'd have to
remove too much gubbins from either side to get a drill in to do the
job.
If I go anywhere else, there is a very good chance that they won't
know any more than I do because there aren't THAT many Liberty's
about, a few, but not that many.
Ewan Scott
>
>
>"Ewan Scott" <ewanscott@btinternet.com> wrote in message
>news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
>: Okay, I've got the aftermarket foglights wired anf they would work if
>: I connected them up direct to the battery - but I'd like to be legal
>: and wire them to work on dipped beam. I'm told that there is a harness
>: socket for the OEM foglights and that it is somewhere on the left side
>: front wing/ fender.
>:
>: I've searched but can't find any unused terminal blocks. Just in case
>: it is reversed for the RHD model I've checked on the right hand side
>: but still no joy.
>:
>: Can anyone tell me where to find it - if it exists?
>:
>: Also, where have people fed accessory cables throught he firewall? I'm
>: looking at the left hand side where the main harness comes through,
>: but something keeps blocking any feed I put through.
>:
>: I don't want to drill any more holes, so any guidance would be
>: welcome.
>:
>: Ewan Scott
>
#15
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 10:18:22 -0500, "Kate" <Kate@dub.dub.dub.com
(please ask)> wrote:
>Whent hey installed the renegade lights on my Liberty, they drilled a hole
>in the firewall.
>Do you not have the instructions or are they some aftermarlet that isn't OEM
>?
Instructions? The company that I got the lights from realised that
no-one reads instructions till something goes wrong. So to save money
on the package they don't publish any fitting instructions :-)
>There were a lot of things about the install that made me just take it in
>and have it done.
>I was glad I did, that way if I had a meltdown, it was covered.
>
That's a fair point. I would have fitted Jeep OEM fogs but.... they
cost about $175 plus carriage, and tax this end. So from the US they
cost me about $200.
If I buy the same lights here they cost about £180, go figure.
So, I buy cheaper aftermarket lights and mount them myself - I've had
them working off the battery, shipped from the US at £48, a quarter of
the price of a UK bought set.
As for having them fitted professionally, well, it's a Jeep and if I
went to the local Jeep Dealer to have them fitted I'd be looking at a
workshop rate of anything between £50 and £90 per hour.
I'm reluctant to drill a hole in the firewayy because - A/ I don't
know what's on the other side, and B/ Even if I wanted to I'd have to
remove too much gubbins from either side to get a drill in to do the
job.
If I go anywhere else, there is a very good chance that they won't
know any more than I do because there aren't THAT many Liberty's
about, a few, but not that many.
Ewan Scott
>
>
>"Ewan Scott" <ewanscott@btinternet.com> wrote in message
>news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
>: Okay, I've got the aftermarket foglights wired anf they would work if
>: I connected them up direct to the battery - but I'd like to be legal
>: and wire them to work on dipped beam. I'm told that there is a harness
>: socket for the OEM foglights and that it is somewhere on the left side
>: front wing/ fender.
>:
>: I've searched but can't find any unused terminal blocks. Just in case
>: it is reversed for the RHD model I've checked on the right hand side
>: but still no joy.
>:
>: Can anyone tell me where to find it - if it exists?
>:
>: Also, where have people fed accessory cables throught he firewall? I'm
>: looking at the left hand side where the main harness comes through,
>: but something keeps blocking any feed I put through.
>:
>: I don't want to drill any more holes, so any guidance would be
>: welcome.
>:
>: Ewan Scott
>
(please ask)> wrote:
>Whent hey installed the renegade lights on my Liberty, they drilled a hole
>in the firewall.
>Do you not have the instructions or are they some aftermarlet that isn't OEM
>?
Instructions? The company that I got the lights from realised that
no-one reads instructions till something goes wrong. So to save money
on the package they don't publish any fitting instructions :-)
>There were a lot of things about the install that made me just take it in
>and have it done.
>I was glad I did, that way if I had a meltdown, it was covered.
>
That's a fair point. I would have fitted Jeep OEM fogs but.... they
cost about $175 plus carriage, and tax this end. So from the US they
cost me about $200.
If I buy the same lights here they cost about £180, go figure.
So, I buy cheaper aftermarket lights and mount them myself - I've had
them working off the battery, shipped from the US at £48, a quarter of
the price of a UK bought set.
As for having them fitted professionally, well, it's a Jeep and if I
went to the local Jeep Dealer to have them fitted I'd be looking at a
workshop rate of anything between £50 and £90 per hour.
I'm reluctant to drill a hole in the firewayy because - A/ I don't
know what's on the other side, and B/ Even if I wanted to I'd have to
remove too much gubbins from either side to get a drill in to do the
job.
If I go anywhere else, there is a very good chance that they won't
know any more than I do because there aren't THAT many Liberty's
about, a few, but not that many.
Ewan Scott
>
>
>"Ewan Scott" <ewanscott@btinternet.com> wrote in message
>news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
>: Okay, I've got the aftermarket foglights wired anf they would work if
>: I connected them up direct to the battery - but I'd like to be legal
>: and wire them to work on dipped beam. I'm told that there is a harness
>: socket for the OEM foglights and that it is somewhere on the left side
>: front wing/ fender.
>:
>: I've searched but can't find any unused terminal blocks. Just in case
>: it is reversed for the RHD model I've checked on the right hand side
>: but still no joy.
>:
>: Can anyone tell me where to find it - if it exists?
>:
>: Also, where have people fed accessory cables throught he firewall? I'm
>: looking at the left hand side where the main harness comes through,
>: but something keeps blocking any feed I put through.
>:
>: I don't want to drill any more holes, so any guidance would be
>: welcome.
>:
>: Ewan Scott
>
#16
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 10:18:22 -0500, "Kate" <Kate@dub.dub.dub.com
(please ask)> wrote:
>Whent hey installed the renegade lights on my Liberty, they drilled a hole
>in the firewall.
>Do you not have the instructions or are they some aftermarlet that isn't OEM
>?
Instructions? The company that I got the lights from realised that
no-one reads instructions till something goes wrong. So to save money
on the package they don't publish any fitting instructions :-)
>There were a lot of things about the install that made me just take it in
>and have it done.
>I was glad I did, that way if I had a meltdown, it was covered.
>
That's a fair point. I would have fitted Jeep OEM fogs but.... they
cost about $175 plus carriage, and tax this end. So from the US they
cost me about $200.
If I buy the same lights here they cost about £180, go figure.
So, I buy cheaper aftermarket lights and mount them myself - I've had
them working off the battery, shipped from the US at £48, a quarter of
the price of a UK bought set.
As for having them fitted professionally, well, it's a Jeep and if I
went to the local Jeep Dealer to have them fitted I'd be looking at a
workshop rate of anything between £50 and £90 per hour.
I'm reluctant to drill a hole in the firewayy because - A/ I don't
know what's on the other side, and B/ Even if I wanted to I'd have to
remove too much gubbins from either side to get a drill in to do the
job.
If I go anywhere else, there is a very good chance that they won't
know any more than I do because there aren't THAT many Liberty's
about, a few, but not that many.
Ewan Scott
>
>
>"Ewan Scott" <ewanscott@btinternet.com> wrote in message
>news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
>: Okay, I've got the aftermarket foglights wired anf they would work if
>: I connected them up direct to the battery - but I'd like to be legal
>: and wire them to work on dipped beam. I'm told that there is a harness
>: socket for the OEM foglights and that it is somewhere on the left side
>: front wing/ fender.
>:
>: I've searched but can't find any unused terminal blocks. Just in case
>: it is reversed for the RHD model I've checked on the right hand side
>: but still no joy.
>:
>: Can anyone tell me where to find it - if it exists?
>:
>: Also, where have people fed accessory cables throught he firewall? I'm
>: looking at the left hand side where the main harness comes through,
>: but something keeps blocking any feed I put through.
>:
>: I don't want to drill any more holes, so any guidance would be
>: welcome.
>:
>: Ewan Scott
>
(please ask)> wrote:
>Whent hey installed the renegade lights on my Liberty, they drilled a hole
>in the firewall.
>Do you not have the instructions or are they some aftermarlet that isn't OEM
>?
Instructions? The company that I got the lights from realised that
no-one reads instructions till something goes wrong. So to save money
on the package they don't publish any fitting instructions :-)
>There were a lot of things about the install that made me just take it in
>and have it done.
>I was glad I did, that way if I had a meltdown, it was covered.
>
That's a fair point. I would have fitted Jeep OEM fogs but.... they
cost about $175 plus carriage, and tax this end. So from the US they
cost me about $200.
If I buy the same lights here they cost about £180, go figure.
So, I buy cheaper aftermarket lights and mount them myself - I've had
them working off the battery, shipped from the US at £48, a quarter of
the price of a UK bought set.
As for having them fitted professionally, well, it's a Jeep and if I
went to the local Jeep Dealer to have them fitted I'd be looking at a
workshop rate of anything between £50 and £90 per hour.
I'm reluctant to drill a hole in the firewayy because - A/ I don't
know what's on the other side, and B/ Even if I wanted to I'd have to
remove too much gubbins from either side to get a drill in to do the
job.
If I go anywhere else, there is a very good chance that they won't
know any more than I do because there aren't THAT many Liberty's
about, a few, but not that many.
Ewan Scott
>
>
>"Ewan Scott" <ewanscott@btinternet.com> wrote in message
>news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
>: Okay, I've got the aftermarket foglights wired anf they would work if
>: I connected them up direct to the battery - but I'd like to be legal
>: and wire them to work on dipped beam. I'm told that there is a harness
>: socket for the OEM foglights and that it is somewhere on the left side
>: front wing/ fender.
>:
>: I've searched but can't find any unused terminal blocks. Just in case
>: it is reversed for the RHD model I've checked on the right hand side
>: but still no joy.
>:
>: Can anyone tell me where to find it - if it exists?
>:
>: Also, where have people fed accessory cables throught he firewall? I'm
>: looking at the left hand side where the main harness comes through,
>: but something keeps blocking any feed I put through.
>:
>: I don't want to drill any more holes, so any guidance would be
>: welcome.
>:
>: Ewan Scott
>
#17
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 16:35:02 +0100, Ewan Scott
<ewanscott@btinternet.com> wrote:
>As for having them fitted professionally, well, it's a Jeep and if I
>went to the local Jeep Dealer to have them fitted I'd be looking at a
>workshop rate of anything between £50 and £90 per hour.
>I'm reluctant to drill a hole in the firewayy because - A/ I don't
>know what's on the other side, and B/ Even if I wanted to I'd have to
>remove too much gubbins from either side to get a drill in to do the
>job.
>
>If I go anywhere else, there is a very good chance that they won't
>know any more than I do because there aren't THAT many Liberty's
>about, a few, but not that many.
>
>Ewan Scott
Ewan -
When I want something run through the firewall of my JGC, I take it to
an automotive audio installation shop. They do that all day for a
living, and know exactly where to run the wires. The last time I had
them run some wires, it cost me $30 U.S. You might check with some
installers in your area to see what they would charge. Sure saves a
lot of grief, and the results will look very professional.
----
<ewanscott@btinternet.com> wrote:
>As for having them fitted professionally, well, it's a Jeep and if I
>went to the local Jeep Dealer to have them fitted I'd be looking at a
>workshop rate of anything between £50 and £90 per hour.
>I'm reluctant to drill a hole in the firewayy because - A/ I don't
>know what's on the other side, and B/ Even if I wanted to I'd have to
>remove too much gubbins from either side to get a drill in to do the
>job.
>
>If I go anywhere else, there is a very good chance that they won't
>know any more than I do because there aren't THAT many Liberty's
>about, a few, but not that many.
>
>Ewan Scott
Ewan -
When I want something run through the firewall of my JGC, I take it to
an automotive audio installation shop. They do that all day for a
living, and know exactly where to run the wires. The last time I had
them run some wires, it cost me $30 U.S. You might check with some
installers in your area to see what they would charge. Sure saves a
lot of grief, and the results will look very professional.
----
#18
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 16:35:02 +0100, Ewan Scott
<ewanscott@btinternet.com> wrote:
>As for having them fitted professionally, well, it's a Jeep and if I
>went to the local Jeep Dealer to have them fitted I'd be looking at a
>workshop rate of anything between £50 and £90 per hour.
>I'm reluctant to drill a hole in the firewayy because - A/ I don't
>know what's on the other side, and B/ Even if I wanted to I'd have to
>remove too much gubbins from either side to get a drill in to do the
>job.
>
>If I go anywhere else, there is a very good chance that they won't
>know any more than I do because there aren't THAT many Liberty's
>about, a few, but not that many.
>
>Ewan Scott
Ewan -
When I want something run through the firewall of my JGC, I take it to
an automotive audio installation shop. They do that all day for a
living, and know exactly where to run the wires. The last time I had
them run some wires, it cost me $30 U.S. You might check with some
installers in your area to see what they would charge. Sure saves a
lot of grief, and the results will look very professional.
----
<ewanscott@btinternet.com> wrote:
>As for having them fitted professionally, well, it's a Jeep and if I
>went to the local Jeep Dealer to have them fitted I'd be looking at a
>workshop rate of anything between £50 and £90 per hour.
>I'm reluctant to drill a hole in the firewayy because - A/ I don't
>know what's on the other side, and B/ Even if I wanted to I'd have to
>remove too much gubbins from either side to get a drill in to do the
>job.
>
>If I go anywhere else, there is a very good chance that they won't
>know any more than I do because there aren't THAT many Liberty's
>about, a few, but not that many.
>
>Ewan Scott
Ewan -
When I want something run through the firewall of my JGC, I take it to
an automotive audio installation shop. They do that all day for a
living, and know exactly where to run the wires. The last time I had
them run some wires, it cost me $30 U.S. You might check with some
installers in your area to see what they would charge. Sure saves a
lot of grief, and the results will look very professional.
----
#19
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
On Fri, 14 Apr 2006 16:35:02 +0100, Ewan Scott
<ewanscott@btinternet.com> wrote:
>As for having them fitted professionally, well, it's a Jeep and if I
>went to the local Jeep Dealer to have them fitted I'd be looking at a
>workshop rate of anything between £50 and £90 per hour.
>I'm reluctant to drill a hole in the firewayy because - A/ I don't
>know what's on the other side, and B/ Even if I wanted to I'd have to
>remove too much gubbins from either side to get a drill in to do the
>job.
>
>If I go anywhere else, there is a very good chance that they won't
>know any more than I do because there aren't THAT many Liberty's
>about, a few, but not that many.
>
>Ewan Scott
Ewan -
When I want something run through the firewall of my JGC, I take it to
an automotive audio installation shop. They do that all day for a
living, and know exactly where to run the wires. The last time I had
them run some wires, it cost me $30 U.S. You might check with some
installers in your area to see what they would charge. Sure saves a
lot of grief, and the results will look very professional.
----
<ewanscott@btinternet.com> wrote:
>As for having them fitted professionally, well, it's a Jeep and if I
>went to the local Jeep Dealer to have them fitted I'd be looking at a
>workshop rate of anything between £50 and £90 per hour.
>I'm reluctant to drill a hole in the firewayy because - A/ I don't
>know what's on the other side, and B/ Even if I wanted to I'd have to
>remove too much gubbins from either side to get a drill in to do the
>job.
>
>If I go anywhere else, there is a very good chance that they won't
>know any more than I do because there aren't THAT many Liberty's
>about, a few, but not that many.
>
>Ewan Scott
Ewan -
When I want something run through the firewall of my JGC, I take it to
an automotive audio installation shop. They do that all day for a
living, and know exactly where to run the wires. The last time I had
them run some wires, it cost me $30 U.S. You might check with some
installers in your area to see what they would charge. Sure saves a
lot of grief, and the results will look very professional.
----
#20
Guest
Posts: n/a
Re: Jeep Liberty Fog Lights
My Liberty was still at the dealership when I was there a few days ago.
I am headed back to town maybe as soon as tomorrow - no promises.
I will make a point of looking to see where he drilled and shoot you a photo
if I can.
Oh, and being the goofy broad that I am, you typed 'fog lights', I read
'running lights'.
Fog lights are a WHOLE different can of worms than the light bar on top that
I was thinking of. Duh!
Anyway, I'll see what I can do to help you from that end. I may even get
some techincal advice from ray or Joey in the shop.
You ought to just call the guys down at the service department, and ask
them. You never know, they might just tell you how, or even print you out a
set of destructions :)
Kate
"Ewan Scott" <ewanscott@btinternet.com> wrote in message
news:npfv32lvnsvurinj9cpd664944sh1os8lt@4ax.com...
: On Fri, 14 Apr 2006 10:18:22 -0500, "Kate" <Kate@dub.dub.dub.com
: (please ask)> wrote:
:
: >Whent hey installed the renegade lights on my Liberty, they drilled a
hole
: >in the firewall.
: >Do you not have the instructions or are they some aftermarlet that isn't
OEM
: >?
:
: Instructions? The company that I got the lights from realised that
: no-one reads instructions till something goes wrong. So to save money
: on the package they don't publish any fitting instructions :-)
:
:
: >There were a lot of things about the install that made me just take it in
: >and have it done.
: >I was glad I did, that way if I had a meltdown, it was covered.
: >
: That's a fair point. I would have fitted Jeep OEM fogs but.... they
: cost about $175 plus carriage, and tax this end. So from the US they
: cost me about $200.
:
: If I buy the same lights here they cost about £180, go figure.
:
: So, I buy cheaper aftermarket lights and mount them myself - I've had
: them working off the battery, shipped from the US at £48, a quarter of
: the price of a UK bought set.
:
: As for having them fitted professionally, well, it's a Jeep and if I
: went to the local Jeep Dealer to have them fitted I'd be looking at a
: workshop rate of anything between £50 and £90 per hour.
: I'm reluctant to drill a hole in the firewayy because - A/ I don't
: know what's on the other side, and B/ Even if I wanted to I'd have to
: remove too much gubbins from either side to get a drill in to do the
: job.
:
: If I go anywhere else, there is a very good chance that they won't
: know any more than I do because there aren't THAT many Liberty's
: about, a few, but not that many.
:
: Ewan Scott
: >
: >
: >"Ewan Scott" <ewanscott@btinternet.com> wrote in message
: >news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
: >: Okay, I've got the aftermarket foglights wired anf they would work if
: >: I connected them up direct to the battery - but I'd like to be legal
: >: and wire them to work on dipped beam. I'm told that there is a harness
: >: socket for the OEM foglights and that it is somewhere on the left side
: >: front wing/ fender.
: >:
: >: I've searched but can't find any unused terminal blocks. Just in case
: >: it is reversed for the RHD model I've checked on the right hand side
: >: but still no joy.
: >:
: >: Can anyone tell me where to find it - if it exists?
: >:
: >: Also, where have people fed accessory cables throught he firewall? I'm
: >: looking at the left hand side where the main harness comes through,
: >: but something keeps blocking any feed I put through.
: >:
: >: I don't want to drill any more holes, so any guidance would be
: >: welcome.
: >:
: >: Ewan Scott
: >
I am headed back to town maybe as soon as tomorrow - no promises.
I will make a point of looking to see where he drilled and shoot you a photo
if I can.
Oh, and being the goofy broad that I am, you typed 'fog lights', I read
'running lights'.
Fog lights are a WHOLE different can of worms than the light bar on top that
I was thinking of. Duh!
Anyway, I'll see what I can do to help you from that end. I may even get
some techincal advice from ray or Joey in the shop.
You ought to just call the guys down at the service department, and ask
them. You never know, they might just tell you how, or even print you out a
set of destructions :)
Kate
"Ewan Scott" <ewanscott@btinternet.com> wrote in message
news:npfv32lvnsvurinj9cpd664944sh1os8lt@4ax.com...
: On Fri, 14 Apr 2006 10:18:22 -0500, "Kate" <Kate@dub.dub.dub.com
: (please ask)> wrote:
:
: >Whent hey installed the renegade lights on my Liberty, they drilled a
hole
: >in the firewall.
: >Do you not have the instructions or are they some aftermarlet that isn't
OEM
: >?
:
: Instructions? The company that I got the lights from realised that
: no-one reads instructions till something goes wrong. So to save money
: on the package they don't publish any fitting instructions :-)
:
:
: >There were a lot of things about the install that made me just take it in
: >and have it done.
: >I was glad I did, that way if I had a meltdown, it was covered.
: >
: That's a fair point. I would have fitted Jeep OEM fogs but.... they
: cost about $175 plus carriage, and tax this end. So from the US they
: cost me about $200.
:
: If I buy the same lights here they cost about £180, go figure.
:
: So, I buy cheaper aftermarket lights and mount them myself - I've had
: them working off the battery, shipped from the US at £48, a quarter of
: the price of a UK bought set.
:
: As for having them fitted professionally, well, it's a Jeep and if I
: went to the local Jeep Dealer to have them fitted I'd be looking at a
: workshop rate of anything between £50 and £90 per hour.
: I'm reluctant to drill a hole in the firewayy because - A/ I don't
: know what's on the other side, and B/ Even if I wanted to I'd have to
: remove too much gubbins from either side to get a drill in to do the
: job.
:
: If I go anywhere else, there is a very good chance that they won't
: know any more than I do because there aren't THAT many Liberty's
: about, a few, but not that many.
:
: Ewan Scott
: >
: >
: >"Ewan Scott" <ewanscott@btinternet.com> wrote in message
: >news:fn1v32pp83dk5noj6927t24iq968k1dmma@4ax.com.. .
: >: Okay, I've got the aftermarket foglights wired anf they would work if
: >: I connected them up direct to the battery - but I'd like to be legal
: >: and wire them to work on dipped beam. I'm told that there is a harness
: >: socket for the OEM foglights and that it is somewhere on the left side
: >: front wing/ fender.
: >:
: >: I've searched but can't find any unused terminal blocks. Just in case
: >: it is reversed for the RHD model I've checked on the right hand side
: >: but still no joy.
: >:
: >: Can anyone tell me where to find it - if it exists?
: >:
: >: Also, where have people fed accessory cables throught he firewall? I'm
: >: looking at the left hand side where the main harness comes through,
: >: but something keeps blocking any feed I put through.
: >:
: >: I don't want to drill any more holes, so any guidance would be
: >: welcome.
: >:
: >: Ewan Scott
: >