Installing Warn Manual locking hubs
10-22-2003, 01:09 PM
#11
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
shared the following:
>No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
>tackle whatever you find after that. You can drive into the garage if you
>want to, or you can do this job right in the driveway.
>
>
>I thought you were getting the Superwinch Hubs.
Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
*just* dropped them off!!!
http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
WOOT WOOT!!!
>
>
>
>
>
>"travis" <travist34removethis@hotmail.com> wrote in message
>news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
>> I bought a set on ebay. Fedex tracking shows that they should be at
>> my house within 4 hours time. Should I jack up the Jeep and put the
>> front end on jackstands on the axle tubes to do this or can I just
>> drive right into the garage, remove the six bolts from each side and
>> yank the hubs and put the new Warn units in and bolt them into place
>> without even jacking up the vehicle? Thank you.
>>
>>
>>
>> --
>> Travis
>> http://jeepadventures.dyndns.org/jeep.html
>> The meek shall inherit the earth. After I'm finished with it.
>> :wq!
--
Travis
http://jeepadventures.dyndns.org/jeep.html
The meek shall inherit the earth. After I'm finished with it.
:wq!
shared the following:
>No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
>tackle whatever you find after that. You can drive into the garage if you
>want to, or you can do this job right in the driveway.
>
>
>I thought you were getting the Superwinch Hubs.
Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
*just* dropped them off!!!
http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
WOOT WOOT!!!
>
>
>
>
>
>"travis" <travist34removethis@hotmail.com> wrote in message
>news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
>> I bought a set on ebay. Fedex tracking shows that they should be at
>> my house within 4 hours time. Should I jack up the Jeep and put the
>> front end on jackstands on the axle tubes to do this or can I just
>> drive right into the garage, remove the six bolts from each side and
>> yank the hubs and put the new Warn units in and bolt them into place
>> without even jacking up the vehicle? Thank you.
>>
>>
>>
>> --
>> Travis
>> http://jeepadventures.dyndns.org/jeep.html
>> The meek shall inherit the earth. After I'm finished with it.
>> :wq!
--
Travis
http://jeepadventures.dyndns.org/jeep.html
The meek shall inherit the earth. After I'm finished with it.
:wq!
10-22-2003, 01:09 PM
#12
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
shared the following:
>No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
>tackle whatever you find after that. You can drive into the garage if you
>want to, or you can do this job right in the driveway.
>
>
>I thought you were getting the Superwinch Hubs.
Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
*just* dropped them off!!!
http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
WOOT WOOT!!!
>
>
>
>
>
>"travis" <travist34removethis@hotmail.com> wrote in message
>news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
>> I bought a set on ebay. Fedex tracking shows that they should be at
>> my house within 4 hours time. Should I jack up the Jeep and put the
>> front end on jackstands on the axle tubes to do this or can I just
>> drive right into the garage, remove the six bolts from each side and
>> yank the hubs and put the new Warn units in and bolt them into place
>> without even jacking up the vehicle? Thank you.
>>
>>
>>
>> --
>> Travis
>> http://jeepadventures.dyndns.org/jeep.html
>> The meek shall inherit the earth. After I'm finished with it.
>> :wq!
--
Travis
http://jeepadventures.dyndns.org/jeep.html
The meek shall inherit the earth. After I'm finished with it.
:wq!
shared the following:
>No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
>tackle whatever you find after that. You can drive into the garage if you
>want to, or you can do this job right in the driveway.
>
>
>I thought you were getting the Superwinch Hubs.
Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
*just* dropped them off!!!
http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
WOOT WOOT!!!
>
>
>
>
>
>"travis" <travist34removethis@hotmail.com> wrote in message
>news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
>> I bought a set on ebay. Fedex tracking shows that they should be at
>> my house within 4 hours time. Should I jack up the Jeep and put the
>> front end on jackstands on the axle tubes to do this or can I just
>> drive right into the garage, remove the six bolts from each side and
>> yank the hubs and put the new Warn units in and bolt them into place
>> without even jacking up the vehicle? Thank you.
>>
>>
>>
>> --
>> Travis
>> http://jeepadventures.dyndns.org/jeep.html
>> The meek shall inherit the earth. After I'm finished with it.
>> :wq!
--
Travis
http://jeepadventures.dyndns.org/jeep.html
The meek shall inherit the earth. After I'm finished with it.
:wq!
10-22-2003, 01:09 PM
#13
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
shared the following:
>No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
>tackle whatever you find after that. You can drive into the garage if you
>want to, or you can do this job right in the driveway.
>
>
>I thought you were getting the Superwinch Hubs.
Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
*just* dropped them off!!!
http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
WOOT WOOT!!!
>
>
>
>
>
>"travis" <travist34removethis@hotmail.com> wrote in message
>news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
>> I bought a set on ebay. Fedex tracking shows that they should be at
>> my house within 4 hours time. Should I jack up the Jeep and put the
>> front end on jackstands on the axle tubes to do this or can I just
>> drive right into the garage, remove the six bolts from each side and
>> yank the hubs and put the new Warn units in and bolt them into place
>> without even jacking up the vehicle? Thank you.
>>
>>
>>
>> --
>> Travis
>> http://jeepadventures.dyndns.org/jeep.html
>> The meek shall inherit the earth. After I'm finished with it.
>> :wq!
--
Travis
http://jeepadventures.dyndns.org/jeep.html
The meek shall inherit the earth. After I'm finished with it.
:wq!
shared the following:
>No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
>tackle whatever you find after that. You can drive into the garage if you
>want to, or you can do this job right in the driveway.
>
>
>I thought you were getting the Superwinch Hubs.
Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
*just* dropped them off!!!
http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
WOOT WOOT!!!
>
>
>
>
>
>"travis" <travist34removethis@hotmail.com> wrote in message
>news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
>> I bought a set on ebay. Fedex tracking shows that they should be at
>> my house within 4 hours time. Should I jack up the Jeep and put the
>> front end on jackstands on the axle tubes to do this or can I just
>> drive right into the garage, remove the six bolts from each side and
>> yank the hubs and put the new Warn units in and bolt them into place
>> without even jacking up the vehicle? Thank you.
>>
>>
>>
>> --
>> Travis
>> http://jeepadventures.dyndns.org/jeep.html
>> The meek shall inherit the earth. After I'm finished with it.
>> :wq!
--
Travis
http://jeepadventures.dyndns.org/jeep.html
The meek shall inherit the earth. After I'm finished with it.
:wq!
10-22-2003, 01:10 PM
#14
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
Hey! Nice carpet!
travis wrote:
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
--
__________________________________________________ _________
tw
03 TJ Rubicon
01 XJ Sport
There is a very fine line between "hobby" and "mental illness."
-- Dave Barry
Pronunciation: 'jEp
Function: noun
Date: 1940
Etymology: probably from g. p. (abbreviation of general purpose)
A small general-purpose motor vehicle with 80-inch wheelbase,
1/4-ton capacity, and four-wheel drive used by the U.S. army in
World War II.
http://www.7slotgrille.com/jeepers/t...ron/index.html
(Please remove the OBVIOUS to reply by email)
__________________________________________________ _________
travis wrote:
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
--
__________________________________________________ _________
tw
03 TJ Rubicon
01 XJ Sport
There is a very fine line between "hobby" and "mental illness."
-- Dave Barry
Pronunciation: 'jEp
Function: noun
Date: 1940
Etymology: probably from g. p. (abbreviation of general purpose)
A small general-purpose motor vehicle with 80-inch wheelbase,
1/4-ton capacity, and four-wheel drive used by the U.S. army in
World War II.
http://www.7slotgrille.com/jeepers/t...ron/index.html
(Please remove the OBVIOUS to reply by email)
__________________________________________________ _________
10-22-2003, 01:10 PM
#15
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
Hey! Nice carpet!
travis wrote:
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
--
__________________________________________________ _________
tw
03 TJ Rubicon
01 XJ Sport
There is a very fine line between "hobby" and "mental illness."
-- Dave Barry
Pronunciation: 'jEp
Function: noun
Date: 1940
Etymology: probably from g. p. (abbreviation of general purpose)
A small general-purpose motor vehicle with 80-inch wheelbase,
1/4-ton capacity, and four-wheel drive used by the U.S. army in
World War II.
http://www.7slotgrille.com/jeepers/t...ron/index.html
(Please remove the OBVIOUS to reply by email)
__________________________________________________ _________
travis wrote:
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
--
__________________________________________________ _________
tw
03 TJ Rubicon
01 XJ Sport
There is a very fine line between "hobby" and "mental illness."
-- Dave Barry
Pronunciation: 'jEp
Function: noun
Date: 1940
Etymology: probably from g. p. (abbreviation of general purpose)
A small general-purpose motor vehicle with 80-inch wheelbase,
1/4-ton capacity, and four-wheel drive used by the U.S. army in
World War II.
http://www.7slotgrille.com/jeepers/t...ron/index.html
(Please remove the OBVIOUS to reply by email)
__________________________________________________ _________
10-22-2003, 01:10 PM
#16
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
Hey! Nice carpet!
travis wrote:
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
--
__________________________________________________ _________
tw
03 TJ Rubicon
01 XJ Sport
There is a very fine line between "hobby" and "mental illness."
-- Dave Barry
Pronunciation: 'jEp
Function: noun
Date: 1940
Etymology: probably from g. p. (abbreviation of general purpose)
A small general-purpose motor vehicle with 80-inch wheelbase,
1/4-ton capacity, and four-wheel drive used by the U.S. army in
World War II.
http://www.7slotgrille.com/jeepers/t...ron/index.html
(Please remove the OBVIOUS to reply by email)
__________________________________________________ _________
travis wrote:
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
--
__________________________________________________ _________
tw
03 TJ Rubicon
01 XJ Sport
There is a very fine line between "hobby" and "mental illness."
-- Dave Barry
Pronunciation: 'jEp
Function: noun
Date: 1940
Etymology: probably from g. p. (abbreviation of general purpose)
A small general-purpose motor vehicle with 80-inch wheelbase,
1/4-ton capacity, and four-wheel drive used by the U.S. army in
World War II.
http://www.7slotgrille.com/jeepers/t...ron/index.html
(Please remove the OBVIOUS to reply by email)
__________________________________________________ _________
10-22-2003, 01:14 PM
#17
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
"travis" <travist34removethis@hotmail.com> wrote in message
news:rcedpvsniievlivujtmsdouravosagji19@4ax.com...
> On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
> shared the following:
>
> >No jacking is needed. Just remove the 6 bolts that hold the hub caps on,
and
> >tackle whatever you find after that. You can drive into the garage if you
> >want to, or you can do this job right in the driveway.
> >
> >
> >I thought you were getting the Superwinch Hubs.
>
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
Just be careful you don't get any grease on that nice carpet...
-Fred W
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 10/11/2003
10-22-2003, 01:14 PM
#18
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
"travis" <travist34removethis@hotmail.com> wrote in message
news:rcedpvsniievlivujtmsdouravosagji19@4ax.com...
> On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
> shared the following:
>
> >No jacking is needed. Just remove the 6 bolts that hold the hub caps on,
and
> >tackle whatever you find after that. You can drive into the garage if you
> >want to, or you can do this job right in the driveway.
> >
> >
> >I thought you were getting the Superwinch Hubs.
>
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
Just be careful you don't get any grease on that nice carpet...
-Fred W
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 10/11/2003
10-22-2003, 01:14 PM
#19
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
"travis" <travist34removethis@hotmail.com> wrote in message
news:rcedpvsniievlivujtmsdouravosagji19@4ax.com...
> On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
> shared the following:
>
> >No jacking is needed. Just remove the 6 bolts that hold the hub caps on,
and
> >tackle whatever you find after that. You can drive into the garage if you
> >want to, or you can do this job right in the driveway.
> >
> >
> >I thought you were getting the Superwinch Hubs.
>
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
Just be careful you don't get any grease on that nice carpet...
-Fred W
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 10/11/2003
10-22-2003, 01:25 PM
#20
Guest
Posts: n/a
Re: Installing Warn Manual locking hubs
Nice!
When I explode my next stock hub, I am getting a set of those.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
travis wrote:
>
> On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
> shared the following:
>
> >No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
> >tackle whatever you find after that. You can drive into the garage if you
> >want to, or you can do this job right in the driveway.
> >
> >
> >I thought you were getting the Superwinch Hubs.
>
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
>
> >
> >
> >
> >
> >
> >"travis" <travist34removethis@hotmail.com> wrote in message
> >news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
> >> I bought a set on ebay. Fedex tracking shows that they should be at
> >> my house within 4 hours time. Should I jack up the Jeep and put the
> >> front end on jackstands on the axle tubes to do this or can I just
> >> drive right into the garage, remove the six bolts from each side and
> >> yank the hubs and put the new Warn units in and bolt them into place
> >> without even jacking up the vehicle? Thank you.
> >>
> >>
> >>
> >> --
> >> Travis
> >> http://jeepadventures.dyndns.org/jeep.html
> >> The meek shall inherit the earth. After I'm finished with it.
> >> :wq!
>
> --
> Travis
> http://jeepadventures.dyndns.org/jeep.html
> The meek shall inherit the earth. After I'm finished with it.
> :wq!
When I explode my next stock hub, I am getting a set of those.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
travis wrote:
>
> On Wed, 22 Oct 2003 09:56:16 -0700, "CRWLR" <beerman@yahoo.com>
> shared the following:
>
> >No jacking is needed. Just remove the 6 bolts that hold the hub caps on, and
> >tackle whatever you find after that. You can drive into the garage if you
> >want to, or you can do this job right in the driveway.
> >
> >
> >I thought you were getting the Superwinch Hubs.
>
> Someone pointed me to a set of Warn hubs on ebay for $75. Fedex
> *just* dropped them off!!!
> http://jeepadventures.dyndns.org/jeep/hubs/hubs1.jpg
> WOOT WOOT!!!
>
> >
> >
> >
> >
> >
> >"travis" <travist34removethis@hotmail.com> wrote in message
> >news:npcdpvgb1b90uepfqb7r6f0qsejstblo6q@4ax.com.. .
> >> I bought a set on ebay. Fedex tracking shows that they should be at
> >> my house within 4 hours time. Should I jack up the Jeep and put the
> >> front end on jackstands on the axle tubes to do this or can I just
> >> drive right into the garage, remove the six bolts from each side and
> >> yank the hubs and put the new Warn units in and bolt them into place
> >> without even jacking up the vehicle? Thank you.
> >>
> >>
> >>
> >> --
> >> Travis
> >> http://jeepadventures.dyndns.org/jeep.html
> >> The meek shall inherit the earth. After I'm finished with it.
> >> :wq!
>
> --
> Travis
> http://jeepadventures.dyndns.org/jeep.html
> The meek shall inherit the earth. After I'm finished with it.
> :wq!