How Do I change my upper radiator hose on a 2000 jeep 4.0L
02-23-2006, 10:41 AM
#21
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
I found the easiest way to drain was to remove the lower hose at radiator
and place a tee in the heater hose.
Also remove the overflow tank and clean.
<sean.c.edwards@gmail.com> wrote in message
news:1140642707.800425.208410@f14g2000cwb.googlegr oups.com...
>I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
>
and place a tee in the heater hose.
Also remove the overflow tank and clean.
<sean.c.edwards@gmail.com> wrote in message
news:1140642707.800425.208410@f14g2000cwb.googlegr oups.com...
>I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
>
02-23-2006, 11:08 AM
#22
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
I use vise grips on the spring clamps. As far as I know, they are 'one
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
02-23-2006, 11:08 AM
#23
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
I use vise grips on the spring clamps. As far as I know, they are 'one
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
02-23-2006, 11:08 AM
#24
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
I use vise grips on the spring clamps. As far as I know, they are 'one
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
02-23-2006, 11:08 AM
#25
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
I use vise grips on the spring clamps. As far as I know, they are 'one
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
use' only clamps. I treat them like anyway that because everyone I have
taken off has changed shape which means the memory is gone in the metal
so they are garbage.
On some newer Jeeps you have to be 'really' 'really' careful with the
radiator hose nipple. The one on the rad should be removed first
because if you remove the thermostat housing end first, you will need to
pull up on the rad hose.
If you pull up on the rad hose with the hose still attached at the
radiator end, the top of that plastic radiator will blow it's seal and
you will need a new rad. If you have an all steel rad, then no worries,
remove whatever end is easiest first.
The drain for my Cherokee is behind the grill by the passenger side
headlight, not sure on the newer ones. You can remove the bottom rad
hose for a drain.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
sean.c.edwards@gmail.com wrote:
>
> I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
02-23-2006, 05:33 PM
#26
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
On Thu, 23 Feb 2006 11:08:53 -0500, Mike Romain wrote:
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
02-23-2006, 05:33 PM
#27
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
On Thu, 23 Feb 2006 11:08:53 -0500, Mike Romain wrote:
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
02-23-2006, 05:33 PM
#28
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
On Thu, 23 Feb 2006 11:08:53 -0500, Mike Romain wrote:
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
02-23-2006, 05:33 PM
#29
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
On Thu, 23 Feb 2006 11:08:53 -0500, Mike Romain wrote:
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
> I use vise grips on the spring clamps.
Ditto. The locking nature of them makes it easier than using regular
pliers.
> As far as I know, they are 'one
> use' only clamps.
The only ones I had to remove was on my old BroncoII. I took them off
without mangling them and used them on the new radiator (only the
radiator was new, everything else I just transferred).
> I treat them like anyway that because everyone I have
> taken off has changed shape which means the memory is gone in the metal
> so they are garbage.
It's called 'k', the spring constant. F=kx (the force of a spring is
equal to 'k' times the distance it is displaced from its origin :-))
When you change the k (often by deforming the material) you have a
different spring. The particulars matter to physicists and mechanical
engineers. You're right that if you reduce the k you won't have the
seal you need and that would be bad.
-D
--
An anxious heart weighs a man down,
but a kind word cheers him up.
Proverbs 12:25
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
02-28-2006, 09:41 PM
#30
Guest
Posts: n/a
Re: How Do I change my upper radiator hose on a 2000 jeep 4.0L
Sorry, but if you gotta ask ...
<sean.c.edwards@gmail.com> wrote in message
news:1140642707.800425.208410@f14g2000cwb.googlegr oups.com...
>I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
>
<sean.c.edwards@gmail.com> wrote in message
news:1140642707.800425.208410@f14g2000cwb.googlegr oups.com...
>I have a 2000 jeep cherokee 4.0L V6 I have a big leak in my upper
> radiator hose. When looking at the clamps they don't look easy to
> remove. I have the part and am ready to replace it. Does anyone have
> any tips on removing the clamps and installing the new hose?
>
> Thanks in Advance
>
