Hey Nathan, got a question for you!
#1
Guest
Posts: n/a
Hey Nathan, got a question for you!
Sorry, but I can't seem to find your email addy anywhere, and didn't know if
you checked the one on your website often...
That trackbar you sent me -- do you remember the make/model? How much lift
was it made for? I'm guessing 3"+ (since I can't get it short enough to fit
the XJ). If so, I'll keep it for the TJ (which will be going to 4.5" next
year) and order a smaller one for the XJ. Thanks!!
Eric
you checked the one on your website often...
That trackbar you sent me -- do you remember the make/model? How much lift
was it made for? I'm guessing 3"+ (since I can't get it short enough to fit
the XJ). If so, I'll keep it for the TJ (which will be going to 4.5" next
year) and order a smaller one for the XJ. Thanks!!
Eric
#2
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
"Eric" <gymrat@***.net> wrote in message
news:DnVXa.235551$o86.74310@news1.central.***.net. ..
> That trackbar you sent me -- do you remember the make/model? How much
lift
> was it made for? I'm guessing 3"+ (since I can't get it short enough to
fit
> the XJ). If so, I'll keep it for the TJ (which will be going to 4.5" next
> year) and order a smaller one for the XJ. Thanks!!
hi eric,
that adjustable trackbar should fit any tj from stock up to at least 6" of
lift. i really dont think it would fit any xj.
--
Nathan W. Collier
http://7SlotGrille.com
news:DnVXa.235551$o86.74310@news1.central.***.net. ..
> That trackbar you sent me -- do you remember the make/model? How much
lift
> was it made for? I'm guessing 3"+ (since I can't get it short enough to
fit
> the XJ). If so, I'll keep it for the TJ (which will be going to 4.5" next
> year) and order a smaller one for the XJ. Thanks!!
hi eric,
that adjustable trackbar should fit any tj from stock up to at least 6" of
lift. i really dont think it would fit any xj.
--
Nathan W. Collier
http://7SlotGrille.com
#3
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
All of the ones I've seen advertised are usually TJ/XJ/ZJ compatible. No
differences between them.
Eric
"Nathan W. Collier" <abuse@A0L.com> wrote in message
news:S4WXa.389569$jp.11178681@twister.southeast.rr .com...
> "Eric" <gymrat@***.net> wrote in message
> news:DnVXa.235551$o86.74310@news1.central.***.net. ..
> > That trackbar you sent me -- do you remember the make/model? How much
> lift
> > was it made for? I'm guessing 3"+ (since I can't get it short enough to
> fit
> > the XJ). If so, I'll keep it for the TJ (which will be going to 4.5"
next
> > year) and order a smaller one for the XJ. Thanks!!
>
> hi eric,
> that adjustable trackbar should fit any tj from stock up to at least 6" of
> lift. i really dont think it would fit any xj.
>
>
> --
> Nathan W. Collier
> http://7SlotGrille.com
>
>
differences between them.
Eric
"Nathan W. Collier" <abuse@A0L.com> wrote in message
news:S4WXa.389569$jp.11178681@twister.southeast.rr .com...
> "Eric" <gymrat@***.net> wrote in message
> news:DnVXa.235551$o86.74310@news1.central.***.net. ..
> > That trackbar you sent me -- do you remember the make/model? How much
> lift
> > was it made for? I'm guessing 3"+ (since I can't get it short enough to
> fit
> > the XJ). If so, I'll keep it for the TJ (which will be going to 4.5"
next
> > year) and order a smaller one for the XJ. Thanks!!
>
> hi eric,
> that adjustable trackbar should fit any tj from stock up to at least 6" of
> lift. i really dont think it would fit any xj.
>
>
> --
> Nathan W. Collier
> http://7SlotGrille.com
>
>
#4
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
"Eric" <gymrat@***.net> wrote in message
news:NiWXa.235712$o86.157441@news1.central.***.net ...
> All of the ones I've seen advertised are usually TJ/XJ/ZJ compatible. No
> differences between them.
wow....learn something new every day. if it makes a difference, the bar was
part of a 4" lift, but my understanding was that it was the same bar from 0"
on up.
--
Nathan W. Collier
http://7SlotGrille.com
news:NiWXa.235712$o86.157441@news1.central.***.net ...
> All of the ones I've seen advertised are usually TJ/XJ/ZJ compatible. No
> differences between them.
wow....learn something new every day. if it makes a difference, the bar was
part of a 4" lift, but my understanding was that it was the same bar from 0"
on up.
--
Nathan W. Collier
http://7SlotGrille.com
#5
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
I'll talk to superlift and see what they say. I've seen some that are 0 -
6" of lift, and a number of them that specify increments -- 0-3", 3.5-5",
5"+, etc. It just depends on the maker as to what they say the range is.
Eric
"Nathan W. Collier" <abuse@A0L.com> wrote in message
news:HoWXa.389722$jp.11182099@twister.southeast.rr .com...
> "Eric" <gymrat@***.net> wrote in message
> news:NiWXa.235712$o86.157441@news1.central.***.net ...
> > All of the ones I've seen advertised are usually TJ/XJ/ZJ compatible.
No
> > differences between them.
>
> wow....learn something new every day. if it makes a difference, the bar
was
> part of a 4" lift, but my understanding was that it was the same bar from
0"
> on up.
>
> --
> Nathan W. Collier
> http://7SlotGrille.com
>
>
6" of lift, and a number of them that specify increments -- 0-3", 3.5-5",
5"+, etc. It just depends on the maker as to what they say the range is.
Eric
"Nathan W. Collier" <abuse@A0L.com> wrote in message
news:HoWXa.389722$jp.11182099@twister.southeast.rr .com...
> "Eric" <gymrat@***.net> wrote in message
> news:NiWXa.235712$o86.157441@news1.central.***.net ...
> > All of the ones I've seen advertised are usually TJ/XJ/ZJ compatible.
No
> > differences between them.
>
> wow....learn something new every day. if it makes a difference, the bar
was
> part of a 4" lift, but my understanding was that it was the same bar from
0"
> on up.
>
> --
> Nathan W. Collier
> http://7SlotGrille.com
>
>
#6
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
"Eric" <gymrat@***.net> wrote in message
news:TQWXa.235897$o86.197580@news1.central.***.net ...
> I'll talk to superlift and see what they say. I've seen some that are 0 -
> 6" of lift, and a number of them that specify increments -- 0-3", 3.5-5",
> 5"+, etc. It just depends on the maker as to what they say the range is.
at 4" of lift, there is only 3/4" difference in the length of the trackbar
over stock. i cant imagine 3/4" requiring a different bar, especially
considering the length of the adjustable end.
--
Nathan W. Collier
http://7SlotGrille.com
news:TQWXa.235897$o86.197580@news1.central.***.net ...
> I'll talk to superlift and see what they say. I've seen some that are 0 -
> 6" of lift, and a number of them that specify increments -- 0-3", 3.5-5",
> 5"+, etc. It just depends on the maker as to what they say the range is.
at 4" of lift, there is only 3/4" difference in the length of the trackbar
over stock. i cant imagine 3/4" requiring a different bar, especially
considering the length of the adjustable end.
--
Nathan W. Collier
http://7SlotGrille.com
#7
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
It seems like this bar is one of two things:
1. Built for a MINIMUM of 4" of lift
or
2. Flawed.
The end just doesn't go in enough. When attached, my steering wheel goes 90
degrees to one side and the axle shifts another inch + over to the
passengers side (meaning it's too long).
Just the tiny bit that the stock bar is off (I don't even think it's 1/2"..
maybe 1/4") is enough to cause DW. I've read on NAXJA that on some XJs, not
all, this is all it takes to have perma-death wobble. It's nuts. I talked
to someone on base that put on a 4.5" lift on their 01 XJ and didn't have a
single problem. Didn't even need a new driveshaft (I've heard some say
that's needed at 3").
Eric
"Nathan W. Collier" <abuse@A0L.com> wrote in message
news:_SWXa.389761$jp.11187185@twister.southeast.rr .com...
> "Eric" <gymrat@***.net> wrote in message
> news:TQWXa.235897$o86.197580@news1.central.***.net ...
> > I'll talk to superlift and see what they say. I've seen some that are
0 -
> > 6" of lift, and a number of them that specify increments -- 0-3",
3.5-5",
> > 5"+, etc. It just depends on the maker as to what they say the range
is.
>
> at 4" of lift, there is only 3/4" difference in the length of the trackbar
> over stock. i cant imagine 3/4" requiring a different bar, especially
> considering the length of the adjustable end.
>
> --
> Nathan W. Collier
> http://7SlotGrille.com
>
>
1. Built for a MINIMUM of 4" of lift
or
2. Flawed.
The end just doesn't go in enough. When attached, my steering wheel goes 90
degrees to one side and the axle shifts another inch + over to the
passengers side (meaning it's too long).
Just the tiny bit that the stock bar is off (I don't even think it's 1/2"..
maybe 1/4") is enough to cause DW. I've read on NAXJA that on some XJs, not
all, this is all it takes to have perma-death wobble. It's nuts. I talked
to someone on base that put on a 4.5" lift on their 01 XJ and didn't have a
single problem. Didn't even need a new driveshaft (I've heard some say
that's needed at 3").
Eric
"Nathan W. Collier" <abuse@A0L.com> wrote in message
news:_SWXa.389761$jp.11187185@twister.southeast.rr .com...
> "Eric" <gymrat@***.net> wrote in message
> news:TQWXa.235897$o86.197580@news1.central.***.net ...
> > I'll talk to superlift and see what they say. I've seen some that are
0 -
> > 6" of lift, and a number of them that specify increments -- 0-3",
3.5-5",
> > 5"+, etc. It just depends on the maker as to what they say the range
is.
>
> at 4" of lift, there is only 3/4" difference in the length of the trackbar
> over stock. i cant imagine 3/4" requiring a different bar, especially
> considering the length of the adjustable end.
>
> --
> Nathan W. Collier
> http://7SlotGrille.com
>
>
#8
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
"Eric" <gymrat@***.net> wrote in message
news:Gc_Xa.240200$o86.92695@news1.central.***.net. ..
> The end just doesn't go in enough.
? was it damaged in shipping or something? mounted perfectly on my tj....
--
Nathan W. Collier
http://7SlotGrille.com
news:Gc_Xa.240200$o86.92695@news1.central.***.net. ..
> The end just doesn't go in enough.
? was it damaged in shipping or something? mounted perfectly on my tj....
--
Nathan W. Collier
http://7SlotGrille.com
#9
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
Hack it off ...
Billy
"Eric" <gymrat@***.net> wrote in message
news:cu_Xa.240552$o86.33226@news1.central.***.net. ..
> I don't think it was damaged. It just seems like the adjustable end has
> (I'm making these numbers up) 5" of thread, and the bar itself only has 3"
> of thread. So the end can only go in part of the way. There plenty of
end
> left, it just won't go into the bar any further (and yes, the retaining
nut
> is loose).
>
> Eric
> "Nathan W. Collier" <abuse@A0L.com> wrote in message
> news:ms_Xa.391034$jp.11236824@twister.southeast.rr .com...
> > "Eric" <gymrat@***.net> wrote in message
> > news:Gc_Xa.240200$o86.92695@news1.central.***.net. ..
> > > The end just doesn't go in enough.
> >
> > ? was it damaged in shipping or something? mounted perfectly on my
> tj....
> >
> > --
> > Nathan W. Collier
> > http://7SlotGrille.com
> >
> >
>
>
Billy
"Eric" <gymrat@***.net> wrote in message
news:cu_Xa.240552$o86.33226@news1.central.***.net. ..
> I don't think it was damaged. It just seems like the adjustable end has
> (I'm making these numbers up) 5" of thread, and the bar itself only has 3"
> of thread. So the end can only go in part of the way. There plenty of
end
> left, it just won't go into the bar any further (and yes, the retaining
nut
> is loose).
>
> Eric
> "Nathan W. Collier" <abuse@A0L.com> wrote in message
> news:ms_Xa.391034$jp.11236824@twister.southeast.rr .com...
> > "Eric" <gymrat@***.net> wrote in message
> > news:Gc_Xa.240200$o86.92695@news1.central.***.net. ..
> > > The end just doesn't go in enough.
> >
> > ? was it damaged in shipping or something? mounted perfectly on my
> tj....
> >
> > --
> > Nathan W. Collier
> > http://7SlotGrille.com
> >
> >
>
>
#10
Guest
Posts: n/a
Re: Hey Nathan, got a question for you!
Hmm.. good point. I guess I'd have to hack the adjustable end. What would
I use?
Eric
"Billy Tolcher" <btolcher@sc.xxxrr.com> wrote in message
news:wy_Xa.391103$jp.11237495@twister.southeast.rr .com...
> Hack it off ...
>
>
> Billy
>
>
> "Eric" <gymrat@***.net> wrote in message
> news:cu_Xa.240552$o86.33226@news1.central.***.net. ..
> > I don't think it was damaged. It just seems like the adjustable end has
> > (I'm making these numbers up) 5" of thread, and the bar itself only has
3"
> > of thread. So the end can only go in part of the way. There plenty of
> end
> > left, it just won't go into the bar any further (and yes, the retaining
> nut
> > is loose).
> >
> > Eric
> > "Nathan W. Collier" <abuse@A0L.com> wrote in message
> > news:ms_Xa.391034$jp.11236824@twister.southeast.rr .com...
> > > "Eric" <gymrat@***.net> wrote in message
> > > news:Gc_Xa.240200$o86.92695@news1.central.***.net. ..
> > > > The end just doesn't go in enough.
> > >
> > > ? was it damaged in shipping or something? mounted perfectly on my
> > tj....
> > >
> > > --
> > > Nathan W. Collier
> > > http://7SlotGrille.com
> > >
> > >
> >
> >
>
>
I use?
Eric
"Billy Tolcher" <btolcher@sc.xxxrr.com> wrote in message
news:wy_Xa.391103$jp.11237495@twister.southeast.rr .com...
> Hack it off ...
>
>
> Billy
>
>
> "Eric" <gymrat@***.net> wrote in message
> news:cu_Xa.240552$o86.33226@news1.central.***.net. ..
> > I don't think it was damaged. It just seems like the adjustable end has
> > (I'm making these numbers up) 5" of thread, and the bar itself only has
3"
> > of thread. So the end can only go in part of the way. There plenty of
> end
> > left, it just won't go into the bar any further (and yes, the retaining
> nut
> > is loose).
> >
> > Eric
> > "Nathan W. Collier" <abuse@A0L.com> wrote in message
> > news:ms_Xa.391034$jp.11236824@twister.southeast.rr .com...
> > > "Eric" <gymrat@***.net> wrote in message
> > > news:Gc_Xa.240200$o86.92695@news1.central.***.net. ..
> > > > The end just doesn't go in enough.
> > >
> > > ? was it damaged in shipping or something? mounted perfectly on my
> > tj....
> > >
> > > --
> > > Nathan W. Collier
> > > http://7SlotGrille.com
> > >
> > >
> >
> >
>
>