Hex Bit for NV3550 Drain/Fill Plugs
Guest
Posts: n/a
Hex Bit for NV3550 Drain/Fill Plugs
Hello,
I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
the NV 3550 5 speed manual transmission.
I have the Mopar recommended fluid, but do not have the proper size hex bit
for the drain/fill plugs. I measured the I/D across two opposite faces with
a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
available, so I don't know if my measurement is correct. I do not know if
the plugs are SAE or Metric.
Does anyone know the proper size hex bit for the plugs on the NV3550? JC
Whitney offers bit sets in SAE or Metric, but want to make sure of the size
first.
Any information would be most appreciated.
Thanks very much,
Campbell Freeman
South Carolina
I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
the NV 3550 5 speed manual transmission.
I have the Mopar recommended fluid, but do not have the proper size hex bit
for the drain/fill plugs. I measured the I/D across two opposite faces with
a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
available, so I don't know if my measurement is correct. I do not know if
the plugs are SAE or Metric.
Does anyone know the proper size hex bit for the plugs on the NV3550? JC
Whitney offers bit sets in SAE or Metric, but want to make sure of the size
first.
Any information would be most appreciated.
Thanks very much,
Campbell Freeman
South Carolina
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
On Wed, 2 Jun 2004 11:52:28 -0400, "Campbell Freeman"
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
On Wed, 2 Jun 2004 11:52:28 -0400, "Campbell Freeman"
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
On Wed, 2 Jun 2004 11:52:28 -0400, "Campbell Freeman"
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
On Wed, 2 Jun 2004 11:52:28 -0400, "Campbell Freeman"
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
<cfreeman@scetv.org> wrote:
>Hello,
>
>I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
>the NV 3550 5 speed manual transmission.
>
>I have the Mopar recommended fluid, but do not have the proper size hex bit
>for the drain/fill plugs. I measured the I/D across two opposite faces with
>a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
>available, so I don't know if my measurement is correct. I do not know if
>the plugs are SAE or Metric.
>
>Does anyone know the proper size hex bit for the plugs on the NV3550? JC
>Whitney offers bit sets in SAE or Metric, but want to make sure of the size
>first.
>
>Any information would be most appreciated.
>
>Thanks very much,
>
>Campbell Freeman
>South Carolina
>
17mm- available at Sears, about nine dollars.
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
i found a hex head bolt that fit into the plug and welded a nut to the other
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
i found a hex head bolt that fit into the plug and welded a nut to the other
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
i found a hex head bolt that fit into the plug and welded a nut to the other
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
Guest
Posts: n/a
Re: Hex Bit for NV3550 Drain/Fill Plugs
i found a hex head bolt that fit into the plug and welded a nut to the other
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
end to use in a socket
saved 20 bucs from the snapon dealer
Campbell Freeman wrote:
> Hello,
>
> I am going to attempt to change the transmission oil in my 2001 TJ (4L) w/
> the NV 3550 5 speed manual transmission.
>
> I have the Mopar recommended fluid, but do not have the proper size hex bit
> for the drain/fill plugs. I measured the I/D across two opposite faces with
> a caliper and came up with 5/8" (~ 16 mm). I do not see 5/8" hex bits
> available, so I don't know if my measurement is correct. I do not know if
> the plugs are SAE or Metric.
>
> Does anyone know the proper size hex bit for the plugs on the NV3550? JC
> Whitney offers bit sets in SAE or Metric, but want to make sure of the size
> first.
>
> Any information would be most appreciated.
>
> Thanks very much,
>
> Campbell Freeman
> South Carolina
Thread
Thread Starter
Forum
Replies
Last Post
Simon Juncal
Jeep Mailing List
6
Jan 10, 2006 06:26 PM
Brian Hawke
Jeep Mailing List
12
Aug 16, 2004 09:10 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
