Help with sourcing Lift Struts for 89 Cherokee LTD
#41
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
Thanks Bill
--
"billy ray" <billy_ray@fuseSPAM.net> wrote in message
news:7fabc$44065a5c$4831b233$23160@FUSE.NET...
> SUPPORT CYLINDER
>
> REMOVAL
>
> WARNING: DO NOT REMOVE A SUPPORT ROD
>
> CYLINDER WITH THE LIFTGATE CLOSED. EACH
>
> SUPPORT ROD PISTON IS OPERATED BY HIGH
>
> PRESSURE GAS. IT CAN CAUSE DAMAGE AND/OR
>
> PERSONAL INJURY IF IT IS REMOVED WITH THE
>
> PISTON COMPRESSED. DO NOT ATTEMPT TO DISASSEMBLE
>
> OR REPAIR A SUPPORT ROD CYLINDER
>
> .
>
> (1) Open the liftgate.
>
> (2) Support the liftgate in the open position.
>
> (3) Remove the clip attaching the support rod to
>
> the ball stud.
>
> (4) Disconnect the support rod from the ball stud.
>
> (5) Remove the bolts attaching the support rod to
>
> the liftgate (Fig. 6).
>
> (6) Separate the support rod from the liftgate.
>
> INSTALLATION
>
> (1) Position the support rod on the liftgate.
>
> (2) Install the bolts attaching the support rod to
>
> the liftgate.
>
> (3) Connect the support rod to the ball stud.
>
> (4) Secure the support rod to the ball stud with
>
> the retainer clip.
>
> (5) Remove the support from the liftgate.
>
>
>
> "NT" <noThanks@hotmail.com> wrote in message
> news:OKsNf.282$Xc3.189@newsfe20.lga...
>
>> Thanks Bill. Should have thought of that.
>>
>> On a related note - has anyone changed their struts? I know that it's a
>> bit of an issue holding the lift gate up, but I can't figure out how the
>> hardware is removed. Any tips? Thanks.
>>
>> --
>>
>> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>> news:4406018B.E63EBC83@***.net...
>>> Might try Ebay:
>>> http://cgi.ebay.com/ebaymotors/Jeep-...41543568QQrdZ1
>>> God Bless America, Bill O|||||||O
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> NT wrote:
>>>>
>>>> I had a look at JC Whitney but I can't find the lift struts anywhere.
>>>> Do
>>>> you have a part number? Thanks.
>>
>>
>
>
--
"billy ray" <billy_ray@fuseSPAM.net> wrote in message
news:7fabc$44065a5c$4831b233$23160@FUSE.NET...
> SUPPORT CYLINDER
>
> REMOVAL
>
> WARNING: DO NOT REMOVE A SUPPORT ROD
>
> CYLINDER WITH THE LIFTGATE CLOSED. EACH
>
> SUPPORT ROD PISTON IS OPERATED BY HIGH
>
> PRESSURE GAS. IT CAN CAUSE DAMAGE AND/OR
>
> PERSONAL INJURY IF IT IS REMOVED WITH THE
>
> PISTON COMPRESSED. DO NOT ATTEMPT TO DISASSEMBLE
>
> OR REPAIR A SUPPORT ROD CYLINDER
>
> .
>
> (1) Open the liftgate.
>
> (2) Support the liftgate in the open position.
>
> (3) Remove the clip attaching the support rod to
>
> the ball stud.
>
> (4) Disconnect the support rod from the ball stud.
>
> (5) Remove the bolts attaching the support rod to
>
> the liftgate (Fig. 6).
>
> (6) Separate the support rod from the liftgate.
>
> INSTALLATION
>
> (1) Position the support rod on the liftgate.
>
> (2) Install the bolts attaching the support rod to
>
> the liftgate.
>
> (3) Connect the support rod to the ball stud.
>
> (4) Secure the support rod to the ball stud with
>
> the retainer clip.
>
> (5) Remove the support from the liftgate.
>
>
>
> "NT" <noThanks@hotmail.com> wrote in message
> news:OKsNf.282$Xc3.189@newsfe20.lga...
>
>> Thanks Bill. Should have thought of that.
>>
>> On a related note - has anyone changed their struts? I know that it's a
>> bit of an issue holding the lift gate up, but I can't figure out how the
>> hardware is removed. Any tips? Thanks.
>>
>> --
>>
>> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>> news:4406018B.E63EBC83@***.net...
>>> Might try Ebay:
>>> http://cgi.ebay.com/ebaymotors/Jeep-...41543568QQrdZ1
>>> God Bless America, Bill O|||||||O
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> NT wrote:
>>>>
>>>> I had a look at JC Whitney but I can't find the lift struts anywhere.
>>>> Do
>>>> you have a part number? Thanks.
>>
>>
>
>
#42
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I'd just use the old broom you've been using. ;-)
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
#43
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I'd just use the old broom you've been using. ;-)
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
#44
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I'd just use the old broom you've been using. ;-)
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
#45
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I'd just use the old broom you've been using. ;-)
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
NT wrote:
>
> Thanks Bill
#46
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I just replaced mine on my '91 Cherokee XJ. It was less than $40.00 shipped
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
#47
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I just replaced mine on my '91 Cherokee XJ. It was less than $40.00 shipped
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
#48
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I just replaced mine on my '91 Cherokee XJ. It was less than $40.00 shipped
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
#49
Guest
Posts: n/a
Re: Help with sourcing Lift Struts for 89 Cherokee LTD
I just replaced mine on my '91 Cherokee XJ. It was less than $40.00 shipped
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
from:
http://planetautoparts.com/
Search for part number 4782 ... that's for StrongArm lift supports ... some
of the best you'll find.
They have free shipping on all orders over $50.00 ... so order a little more
and you'll get the free shipping.
It was really easy to replace them ... I wondered about it like you did, but
once you get going with it, you'll be fine. Pull out the little clips that
hold them in, then just pop it off the ball stud. The new one pops on, then
put the clip back on.
Good luck.
Robert Dyke
Montana Software - Internet Accelerator Technology.
http://www.montanasoft.com/
"NT" <noThanks@hotmail.com> wrote in message
news:xZ%Mf.12108$wZ4.1431@newsfe16.lga...
> Hi:
>
> I'm looking to replace the rear door lift struts on my 89 Cherokee Ltd.
Any
> suggestions on a good replacement and a reliable on line source? Thanks
for
> any advice.
>
>
>
> --
>
>
>
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)