Bob

Thanks for thhe advice. I really appreciate all the help and
suggestions everyone has given me with this transfer case work.

I got the transfer case put back together tonight. I haven't torqued
down the rear yoke fully yet; it says it needs 150 lb-ft of torque. I
can't get it over 125 w/it turning with the torque wrench (I have the
tranny in gear right now). I'm thinking I probably need a nice,
massive adjustable wrench to hold that yoke in place while I finish
torquing the nut down.

This is a small problem compared to everything else I've figured out.
It's so nice that this mod has finally finished successfully.

Later!
/Bob


Mike Romain <romainm@sympatico.ca> wrote in message news:<3F96A1F0.F36D4DE3@sympatico.ca>...
> Good luck.
>
> Just a tip on the silicone. Read the directions 'carefully' and let it
> 'cure' the right length of time, usually 24 hours before adding fluid.
> This will insure no leaks.
>
> Some silicones require a slight skim over before assembly but most these
> days say to assemble 'before' it skims over.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Bob wrote:
> >
> > Well, an update:
> >
> > I haven't retried attaching the rear of the case yet; had some other
> > stuff to take care of last night. I did go pick up a new oil pump (the
> > "oil pump housing + gasket" was the correct item). I also talked to
> > the guys at the shop, and they gave me some new silicone gasket maker
> > in an aerosol-type "easy-cheese" style canister, and said that should
> > work well for me, as well as an applicator tip and specific
> > instructions on how much to use and how much is too much. So hopefully
> > I won't have the same gooey mess when I re-attempt this tonight as I
> > did night before last. I'm optimistic things will go as they should
> > have the first time, now, so wish me luck for when I try again
> > tonight! ;-)
> >
> > /Bob

Bob

Thanks for thhe advice. I really appreciate all the help and
suggestions everyone has given me with this transfer case work.

I got the transfer case put back together tonight. I haven't torqued
down the rear yoke fully yet; it says it needs 150 lb-ft of torque. I
can't get it over 125 w/it turning with the torque wrench (I have the
tranny in gear right now). I'm thinking I probably need a nice,
massive adjustable wrench to hold that yoke in place while I finish
torquing the nut down.

This is a small problem compared to everything else I've figured out.
It's so nice that this mod has finally finished successfully.

Later!
/Bob


Mike Romain <romainm@sympatico.ca> wrote in message news:<3F96A1F0.F36D4DE3@sympatico.ca>...
> Good luck.
>
> Just a tip on the silicone. Read the directions 'carefully' and let it
> 'cure' the right length of time, usually 24 hours before adding fluid.
> This will insure no leaks.
>
> Some silicones require a slight skim over before assembly but most these
> days say to assemble 'before' it skims over.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Bob wrote:
> >
> > Well, an update:
> >
> > I haven't retried attaching the rear of the case yet; had some other
> > stuff to take care of last night. I did go pick up a new oil pump (the
> > "oil pump housing + gasket" was the correct item). I also talked to
> > the guys at the shop, and they gave me some new silicone gasket maker
> > in an aerosol-type "easy-cheese" style canister, and said that should
> > work well for me, as well as an applicator tip and specific
> > instructions on how much to use and how much is too much. So hopefully
> > I won't have the same gooey mess when I re-attempt this tonight as I
> > did night before last. I'm optimistic things will go as they should
> > have the first time, now, so wish me luck for when I try again
> > tonight! ;-)
> >
> > /Bob

Bob

Thanks for thhe advice. I really appreciate all the help and
suggestions everyone has given me with this transfer case work.

I got the transfer case put back together tonight. I haven't torqued
down the rear yoke fully yet; it says it needs 150 lb-ft of torque. I
can't get it over 125 w/it turning with the torque wrench (I have the
tranny in gear right now). I'm thinking I probably need a nice,
massive adjustable wrench to hold that yoke in place while I finish
torquing the nut down.

This is a small problem compared to everything else I've figured out.
It's so nice that this mod has finally finished successfully.

Later!
/Bob


Mike Romain <romainm@sympatico.ca> wrote in message news:<3F96A1F0.F36D4DE3@sympatico.ca>...
> Good luck.
>
> Just a tip on the silicone. Read the directions 'carefully' and let it
> 'cure' the right length of time, usually 24 hours before adding fluid.
> This will insure no leaks.
>
> Some silicones require a slight skim over before assembly but most these
> days say to assemble 'before' it skims over.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Bob wrote:
> >
> > Well, an update:
> >
> > I haven't retried attaching the rear of the case yet; had some other
> > stuff to take care of last night. I did go pick up a new oil pump (the
> > "oil pump housing + gasket" was the correct item). I also talked to
> > the guys at the shop, and they gave me some new silicone gasket maker
> > in an aerosol-type "easy-cheese" style canister, and said that should
> > work well for me, as well as an applicator tip and specific
> > instructions on how much to use and how much is too much. So hopefully
> > I won't have the same gooey mess when I re-attempt this tonight as I
> > did night before last. I'm optimistic things will go as they should
> > have the first time, now, so wish me luck for when I try again
> > tonight! ;-)
> >
> > /Bob