HELP my jeeps drowning
11-24-2004, 10:56 PM
#1
Guest
Posts: n/a
HELP my jeeps drowning
OK i need help, its raining like crazy and going to for the next five
monthes,
my cowl/winshild gasket was toast so i went and bought a new one at olymic
4X4
(90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
softtop bars, rolled the top back, dropped the winshield unscrewed the old
one,
cleaned it all out dryed it all,
then replaced it with the new one, making shure ithe lips were into the
gasket
and it was seated correctly,
tilted the windshield back up and re-assembled it all,
so now its been sitting outside in the pouring rain and ya you guessed it,
my floor-boards are soaked,,and carpet, im dripping water from under the
dash
and
from the corners by the plates above the speakers,
,
i need help,,or my dash is gonna rot, or give up the electrical ghost,
,
was i supposed to calk behind the outside lip?
was i supposed to calk anywhere on the gasket,,top,,bottom??
,
help, please,
John Pike,
email me at scope_addict "at" verizon "dot" net
or here,
anything quick would be most apriciated,, thanks again
monthes,
my cowl/winshild gasket was toast so i went and bought a new one at olymic
4X4
(90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
softtop bars, rolled the top back, dropped the winshield unscrewed the old
one,
cleaned it all out dryed it all,
then replaced it with the new one, making shure ithe lips were into the
gasket
and it was seated correctly,
tilted the windshield back up and re-assembled it all,
so now its been sitting outside in the pouring rain and ya you guessed it,
my floor-boards are soaked,,and carpet, im dripping water from under the
dash
and
from the corners by the plates above the speakers,
,
i need help,,or my dash is gonna rot, or give up the electrical ghost,
,
was i supposed to calk behind the outside lip?
was i supposed to calk anywhere on the gasket,,top,,bottom??
,
help, please,
John Pike,
email me at scope_addict "at" verizon "dot" net
or here,
anything quick would be most apriciated,, thanks again
11-24-2004, 11:08 PM
#2
Guest
Posts: n/a
Re: HELP my jeeps drowning
Cowl vent drain:
http://www.Google.com/groups?hl=en&l...eep%252Bwillys
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
somebody wrote:
>
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
http://www.Google.com/groups?hl=en&l...eep%252Bwillys
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
somebody wrote:
>
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
11-24-2004, 11:08 PM
#3
Guest
Posts: n/a
Re: HELP my jeeps drowning
Cowl vent drain:
http://www.Google.com/groups?hl=en&l...eep%252Bwillys
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
somebody wrote:
>
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
http://www.Google.com/groups?hl=en&l...eep%252Bwillys
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
somebody wrote:
>
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
11-24-2004, 11:08 PM
#4
Guest
Posts: n/a
Re: HELP my jeeps drowning
Cowl vent drain:
http://www.Google.com/groups?hl=en&l...eep%252Bwillys
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
somebody wrote:
>
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
http://www.Google.com/groups?hl=en&l...eep%252Bwillys
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
somebody wrote:
>
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
11-25-2004, 07:23 AM
#5
Guest
Posts: n/a
Re: HELP my jeeps drowning
First try adjusting the bar to allow the window to pull back further to
compress the gasket and check your wiper motor cover ensure it is up tight
in the lip of the gasket this assists in compressing the gasket against the
top and bottom of the window.
If all else fails and you do not need to drop your windshield silicone can
be your friend. Remove the gasket, run a bead around the complete
circumference of the dash mating area, replace the gasket, and do the same
around the bottom of the windshield. I did this on my CJ when it came time
to replace the gasket because aftermarket gaskets are not as good as the
OEMs. It should be as leak proof as a frogs butt.
HarryS
"somebody" <scope_addict@verizon.net> wrote in message
news:KJcpd.3807$Rs2.1118@trnddc03...
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
>
>
compress the gasket and check your wiper motor cover ensure it is up tight
in the lip of the gasket this assists in compressing the gasket against the
top and bottom of the window.
If all else fails and you do not need to drop your windshield silicone can
be your friend. Remove the gasket, run a bead around the complete
circumference of the dash mating area, replace the gasket, and do the same
around the bottom of the windshield. I did this on my CJ when it came time
to replace the gasket because aftermarket gaskets are not as good as the
OEMs. It should be as leak proof as a frogs butt.
HarryS
"somebody" <scope_addict@verizon.net> wrote in message
news:KJcpd.3807$Rs2.1118@trnddc03...
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
>
>
11-25-2004, 07:23 AM
#6
Guest
Posts: n/a
Re: HELP my jeeps drowning
First try adjusting the bar to allow the window to pull back further to
compress the gasket and check your wiper motor cover ensure it is up tight
in the lip of the gasket this assists in compressing the gasket against the
top and bottom of the window.
If all else fails and you do not need to drop your windshield silicone can
be your friend. Remove the gasket, run a bead around the complete
circumference of the dash mating area, replace the gasket, and do the same
around the bottom of the windshield. I did this on my CJ when it came time
to replace the gasket because aftermarket gaskets are not as good as the
OEMs. It should be as leak proof as a frogs butt.
HarryS
"somebody" <scope_addict@verizon.net> wrote in message
news:KJcpd.3807$Rs2.1118@trnddc03...
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
>
>
compress the gasket and check your wiper motor cover ensure it is up tight
in the lip of the gasket this assists in compressing the gasket against the
top and bottom of the window.
If all else fails and you do not need to drop your windshield silicone can
be your friend. Remove the gasket, run a bead around the complete
circumference of the dash mating area, replace the gasket, and do the same
around the bottom of the windshield. I did this on my CJ when it came time
to replace the gasket because aftermarket gaskets are not as good as the
OEMs. It should be as leak proof as a frogs butt.
HarryS
"somebody" <scope_addict@verizon.net> wrote in message
news:KJcpd.3807$Rs2.1118@trnddc03...
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
>
>
11-25-2004, 07:23 AM
#7
Guest
Posts: n/a
Re: HELP my jeeps drowning
First try adjusting the bar to allow the window to pull back further to
compress the gasket and check your wiper motor cover ensure it is up tight
in the lip of the gasket this assists in compressing the gasket against the
top and bottom of the window.
If all else fails and you do not need to drop your windshield silicone can
be your friend. Remove the gasket, run a bead around the complete
circumference of the dash mating area, replace the gasket, and do the same
around the bottom of the windshield. I did this on my CJ when it came time
to replace the gasket because aftermarket gaskets are not as good as the
OEMs. It should be as leak proof as a frogs butt.
HarryS
"somebody" <scope_addict@verizon.net> wrote in message
news:KJcpd.3807$Rs2.1118@trnddc03...
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
>
>
compress the gasket and check your wiper motor cover ensure it is up tight
in the lip of the gasket this assists in compressing the gasket against the
top and bottom of the window.
If all else fails and you do not need to drop your windshield silicone can
be your friend. Remove the gasket, run a bead around the complete
circumference of the dash mating area, replace the gasket, and do the same
around the bottom of the windshield. I did this on my CJ when it came time
to replace the gasket because aftermarket gaskets are not as good as the
OEMs. It should be as leak proof as a frogs butt.
HarryS
"somebody" <scope_addict@verizon.net> wrote in message
news:KJcpd.3807$Rs2.1118@trnddc03...
> OK i need help, its raining like crazy and going to for the next five
> monthes,
> my cowl/winshild gasket was toast so i went and bought a new one at olymic
> 4X4
> (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> softtop bars, rolled the top back, dropped the winshield unscrewed the old
> one,
> cleaned it all out dryed it all,
> then replaced it with the new one, making shure ithe lips were into the
> gasket
> and it was seated correctly,
> tilted the windshield back up and re-assembled it all,
> so now its been sitting outside in the pouring rain and ya you guessed it,
> my floor-boards are soaked,,and carpet, im dripping water from under the
> dash
> and
> from the corners by the plates above the speakers,
> ,
> i need help,,or my dash is gonna rot, or give up the electrical ghost,
> ,
> was i supposed to calk behind the outside lip?
> was i supposed to calk anywhere on the gasket,,top,,bottom??
> ,
> help, please,
> John Pike,
> email me at scope_addict "at" verizon "dot" net
> or here,
> anything quick would be most apriciated,, thanks again
>
>
11-25-2004, 08:46 AM
#8
Guest
Posts: n/a
Re: HELP my jeeps drowning
The stock ones come with two sided tape in that front lip to keep water
out. They will leak like a sieve without it.
Do 'not' use silicone of any type. It reacts with humidity and will
fast rot out the frame from it's fumes going acid.
If you must use goop, get the proper windshield stuff.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"JohnE.P.--JEP" wrote:
>
> Thanks Bill
> but its not coming from the vent drain. i have my vent covered over on
> the outside, and have checked the drain,
> question 1-- was i supposed tp use adhesive on the top part of the
> winshield/cowl gasket?
> question 2--if so what type of adhesive??
>
> thanks
> john p new Jeepers-creepers owner,,,
>
> L.W.(ßill) ------ III <----------@***.net> wrote in message news:<41A55AB4.4AA44CDF@***.net>...
> > Cowl vent drain:
> > http://www.Google.com/groups?hl=en&l...eep%252Bwillys
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > somebody wrote:
> > >
> > > OK i need help, its raining like crazy and going to for the next five
> > > monthes,
> > > my cowl/winshild gasket was toast so i went and bought a new one at olymic
> > > 4X4
> > > (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> > > softtop bars, rolled the top back, dropped the winshield unscrewed the old
> > > one,
> > > cleaned it all out dryed it all,
> > > then replaced it with the new one, making shure ithe lips were into the
> > > gasket
> > > and it was seated correctly,
> > > tilted the windshield back up and re-assembled it all,
> > > so now its been sitting outside in the pouring rain and ya you guessed it,
> > > my floor-boards are soaked,,and carpet, im dripping water from under the
> > > dash
> > > and
> > > from the corners by the plates above the speakers,
> > > ,
> > > i need help,,or my dash is gonna rot, or give up the electrical ghost,
> > > ,
> > > was i supposed to calk behind the outside lip?
> > > was i supposed to calk anywhere on the gasket,,top,,bottom??
> > > ,
> > > help, please,
> > > John Pike,
> > > email me at scope_addict "at" verizon "dot" net
> > > or here,
> > > anything quick would be most apriciated,, thanks again
out. They will leak like a sieve without it.
Do 'not' use silicone of any type. It reacts with humidity and will
fast rot out the frame from it's fumes going acid.
If you must use goop, get the proper windshield stuff.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"JohnE.P.--JEP" wrote:
>
> Thanks Bill
> but its not coming from the vent drain. i have my vent covered over on
> the outside, and have checked the drain,
> question 1-- was i supposed tp use adhesive on the top part of the
> winshield/cowl gasket?
> question 2--if so what type of adhesive??
>
> thanks
> john p new Jeepers-creepers owner,,,
>
> L.W.(ßill) ------ III <----------@***.net> wrote in message news:<41A55AB4.4AA44CDF@***.net>...
> > Cowl vent drain:
> > http://www.Google.com/groups?hl=en&l...eep%252Bwillys
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > somebody wrote:
> > >
> > > OK i need help, its raining like crazy and going to for the next five
> > > monthes,
> > > my cowl/winshild gasket was toast so i went and bought a new one at olymic
> > > 4X4
> > > (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> > > softtop bars, rolled the top back, dropped the winshield unscrewed the old
> > > one,
> > > cleaned it all out dryed it all,
> > > then replaced it with the new one, making shure ithe lips were into the
> > > gasket
> > > and it was seated correctly,
> > > tilted the windshield back up and re-assembled it all,
> > > so now its been sitting outside in the pouring rain and ya you guessed it,
> > > my floor-boards are soaked,,and carpet, im dripping water from under the
> > > dash
> > > and
> > > from the corners by the plates above the speakers,
> > > ,
> > > i need help,,or my dash is gonna rot, or give up the electrical ghost,
> > > ,
> > > was i supposed to calk behind the outside lip?
> > > was i supposed to calk anywhere on the gasket,,top,,bottom??
> > > ,
> > > help, please,
> > > John Pike,
> > > email me at scope_addict "at" verizon "dot" net
> > > or here,
> > > anything quick would be most apriciated,, thanks again
11-25-2004, 08:46 AM
#9
Guest
Posts: n/a
Re: HELP my jeeps drowning
The stock ones come with two sided tape in that front lip to keep water
out. They will leak like a sieve without it.
Do 'not' use silicone of any type. It reacts with humidity and will
fast rot out the frame from it's fumes going acid.
If you must use goop, get the proper windshield stuff.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"JohnE.P.--JEP" wrote:
>
> Thanks Bill
> but its not coming from the vent drain. i have my vent covered over on
> the outside, and have checked the drain,
> question 1-- was i supposed tp use adhesive on the top part of the
> winshield/cowl gasket?
> question 2--if so what type of adhesive??
>
> thanks
> john p new Jeepers-creepers owner,,,
>
> L.W.(ßill) ------ III <----------@***.net> wrote in message news:<41A55AB4.4AA44CDF@***.net>...
> > Cowl vent drain:
> > http://www.Google.com/groups?hl=en&l...eep%252Bwillys
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > somebody wrote:
> > >
> > > OK i need help, its raining like crazy and going to for the next five
> > > monthes,
> > > my cowl/winshild gasket was toast so i went and bought a new one at olymic
> > > 4X4
> > > (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> > > softtop bars, rolled the top back, dropped the winshield unscrewed the old
> > > one,
> > > cleaned it all out dryed it all,
> > > then replaced it with the new one, making shure ithe lips were into the
> > > gasket
> > > and it was seated correctly,
> > > tilted the windshield back up and re-assembled it all,
> > > so now its been sitting outside in the pouring rain and ya you guessed it,
> > > my floor-boards are soaked,,and carpet, im dripping water from under the
> > > dash
> > > and
> > > from the corners by the plates above the speakers,
> > > ,
> > > i need help,,or my dash is gonna rot, or give up the electrical ghost,
> > > ,
> > > was i supposed to calk behind the outside lip?
> > > was i supposed to calk anywhere on the gasket,,top,,bottom??
> > > ,
> > > help, please,
> > > John Pike,
> > > email me at scope_addict "at" verizon "dot" net
> > > or here,
> > > anything quick would be most apriciated,, thanks again
out. They will leak like a sieve without it.
Do 'not' use silicone of any type. It reacts with humidity and will
fast rot out the frame from it's fumes going acid.
If you must use goop, get the proper windshield stuff.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"JohnE.P.--JEP" wrote:
>
> Thanks Bill
> but its not coming from the vent drain. i have my vent covered over on
> the outside, and have checked the drain,
> question 1-- was i supposed tp use adhesive on the top part of the
> winshield/cowl gasket?
> question 2--if so what type of adhesive??
>
> thanks
> john p new Jeepers-creepers owner,,,
>
> L.W.(ßill) ------ III <----------@***.net> wrote in message news:<41A55AB4.4AA44CDF@***.net>...
> > Cowl vent drain:
> > http://www.Google.com/groups?hl=en&l...eep%252Bwillys
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > somebody wrote:
> > >
> > > OK i need help, its raining like crazy and going to for the next five
> > > monthes,
> > > my cowl/winshild gasket was toast so i went and bought a new one at olymic
> > > 4X4
> > > (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> > > softtop bars, rolled the top back, dropped the winshield unscrewed the old
> > > one,
> > > cleaned it all out dryed it all,
> > > then replaced it with the new one, making shure ithe lips were into the
> > > gasket
> > > and it was seated correctly,
> > > tilted the windshield back up and re-assembled it all,
> > > so now its been sitting outside in the pouring rain and ya you guessed it,
> > > my floor-boards are soaked,,and carpet, im dripping water from under the
> > > dash
> > > and
> > > from the corners by the plates above the speakers,
> > > ,
> > > i need help,,or my dash is gonna rot, or give up the electrical ghost,
> > > ,
> > > was i supposed to calk behind the outside lip?
> > > was i supposed to calk anywhere on the gasket,,top,,bottom??
> > > ,
> > > help, please,
> > > John Pike,
> > > email me at scope_addict "at" verizon "dot" net
> > > or here,
> > > anything quick would be most apriciated,, thanks again
11-25-2004, 08:46 AM
#10
Guest
Posts: n/a
Re: HELP my jeeps drowning
The stock ones come with two sided tape in that front lip to keep water
out. They will leak like a sieve without it.
Do 'not' use silicone of any type. It reacts with humidity and will
fast rot out the frame from it's fumes going acid.
If you must use goop, get the proper windshield stuff.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"JohnE.P.--JEP" wrote:
>
> Thanks Bill
> but its not coming from the vent drain. i have my vent covered over on
> the outside, and have checked the drain,
> question 1-- was i supposed tp use adhesive on the top part of the
> winshield/cowl gasket?
> question 2--if so what type of adhesive??
>
> thanks
> john p new Jeepers-creepers owner,,,
>
> L.W.(ßill) ------ III <----------@***.net> wrote in message news:<41A55AB4.4AA44CDF@***.net>...
> > Cowl vent drain:
> > http://www.Google.com/groups?hl=en&l...eep%252Bwillys
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > somebody wrote:
> > >
> > > OK i need help, its raining like crazy and going to for the next five
> > > monthes,
> > > my cowl/winshild gasket was toast so i went and bought a new one at olymic
> > > 4X4
> > > (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> > > softtop bars, rolled the top back, dropped the winshield unscrewed the old
> > > one,
> > > cleaned it all out dryed it all,
> > > then replaced it with the new one, making shure ithe lips were into the
> > > gasket
> > > and it was seated correctly,
> > > tilted the windshield back up and re-assembled it all,
> > > so now its been sitting outside in the pouring rain and ya you guessed it,
> > > my floor-boards are soaked,,and carpet, im dripping water from under the
> > > dash
> > > and
> > > from the corners by the plates above the speakers,
> > > ,
> > > i need help,,or my dash is gonna rot, or give up the electrical ghost,
> > > ,
> > > was i supposed to calk behind the outside lip?
> > > was i supposed to calk anywhere on the gasket,,top,,bottom??
> > > ,
> > > help, please,
> > > John Pike,
> > > email me at scope_addict "at" verizon "dot" net
> > > or here,
> > > anything quick would be most apriciated,, thanks again
out. They will leak like a sieve without it.
Do 'not' use silicone of any type. It reacts with humidity and will
fast rot out the frame from it's fumes going acid.
If you must use goop, get the proper windshield stuff.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"JohnE.P.--JEP" wrote:
>
> Thanks Bill
> but its not coming from the vent drain. i have my vent covered over on
> the outside, and have checked the drain,
> question 1-- was i supposed tp use adhesive on the top part of the
> winshield/cowl gasket?
> question 2--if so what type of adhesive??
>
> thanks
> john p new Jeepers-creepers owner,,,
>
> L.W.(ßill) ------ III <----------@***.net> wrote in message news:<41A55AB4.4AA44CDF@***.net>...
> > Cowl vent drain:
> > http://www.Google.com/groups?hl=en&l...eep%252Bwillys
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > somebody wrote:
> > >
> > > OK i need help, its raining like crazy and going to for the next five
> > > monthes,
> > > my cowl/winshild gasket was toast so i went and bought a new one at olymic
> > > 4X4
> > > (90YJ) i unhooked all my crap on the winshield,,bars,,and inside plates,
> > > softtop bars, rolled the top back, dropped the winshield unscrewed the old
> > > one,
> > > cleaned it all out dryed it all,
> > > then replaced it with the new one, making shure ithe lips were into the
> > > gasket
> > > and it was seated correctly,
> > > tilted the windshield back up and re-assembled it all,
> > > so now its been sitting outside in the pouring rain and ya you guessed it,
> > > my floor-boards are soaked,,and carpet, im dripping water from under the
> > > dash
> > > and
> > > from the corners by the plates above the speakers,
> > > ,
> > > i need help,,or my dash is gonna rot, or give up the electrical ghost,
> > > ,
> > > was i supposed to calk behind the outside lip?
> > > was i supposed to calk anywhere on the gasket,,top,,bottom??
> > > ,
> > > help, please,
> > > John Pike,
> > > email me at scope_addict "at" verizon "dot" net
> > > or here,
> > > anything quick would be most apriciated,, thanks again