Headlights problem on XJ 1992
#21
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
On Fri, 2 Apr 2004, Mike Romain wrote:
> I am thinking the same thing and I was implying once tripped, the
> breaker will never be stable again.
I hadn't known that about automotive breakers, but I should have guessed,
thanks for the tip. Regular AC breakers get weak if they get cycled, but
it takes quite a few cycles to soften them up to the point that you'll
notice.
> I was thinking he tripped the new one before he cleaned up the wires
> maybe?
Dunno. I'm hoping that he comes back and gives us more detail.
> Lee Ayrton wrote:
> >
> > The clue that I twigged on was "connection on headlamp switch (tan colour
> > wire) was a little bit melted". Something made that connection hot,
> > either over-load or corrosion. He says that he's replaced both the light
> > switch and the headlamp dimmer switch, it would be good to know if this
> > problem was the reason he changed out the switches or if there was
> > something else going on. Either way it sounds like he's tripping the
> > breaker, it doesn't seem likely that a bad ground is going to cause that.
> >
> > On Thu, 1 Apr 2004, Mike Romain wrote:
> >
> > > Do you have aftermarket bulbs in the lights?
> > >
> > > If the lights draw too many amps without a relay, they will blow a
> > > circuit breaker inside the headlight switch. Once this breaker has been
> > > popped, it doesn't ever hold full power after.
> > >
> > > The main ground is a wire mesh strap from the engine head to the
> > > firewall.
> > >
> > > If you follow the headlight wiring, at the end near one light you will
> > > find a black wire bolted to the fender or grill. This is the main
> > > ground.
> > >
> > > The headlight switch has a ground wire under the dash near the steering
> > > column.
> > >
> > > Mike
> > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > 88 Cherokee 235 BFG AT's
> > >
> > > Davey wrote:
> > > >
> > > > Please, anyone can help me?
> > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > beam only) they start flickering and then off, only parking lights stay.
> > > > After one minute of waiting , i pull the switch again and lights are back
> > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > jack and connected everything directly on place but problem is still there.
> > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > problem.
> > > > If anyone has any idea please help.
> > > > Thanks
> > > > Davey
> > >
>
> I am thinking the same thing and I was implying once tripped, the
> breaker will never be stable again.
I hadn't known that about automotive breakers, but I should have guessed,
thanks for the tip. Regular AC breakers get weak if they get cycled, but
it takes quite a few cycles to soften them up to the point that you'll
notice.
> I was thinking he tripped the new one before he cleaned up the wires
> maybe?
Dunno. I'm hoping that he comes back and gives us more detail.
> Lee Ayrton wrote:
> >
> > The clue that I twigged on was "connection on headlamp switch (tan colour
> > wire) was a little bit melted". Something made that connection hot,
> > either over-load or corrosion. He says that he's replaced both the light
> > switch and the headlamp dimmer switch, it would be good to know if this
> > problem was the reason he changed out the switches or if there was
> > something else going on. Either way it sounds like he's tripping the
> > breaker, it doesn't seem likely that a bad ground is going to cause that.
> >
> > On Thu, 1 Apr 2004, Mike Romain wrote:
> >
> > > Do you have aftermarket bulbs in the lights?
> > >
> > > If the lights draw too many amps without a relay, they will blow a
> > > circuit breaker inside the headlight switch. Once this breaker has been
> > > popped, it doesn't ever hold full power after.
> > >
> > > The main ground is a wire mesh strap from the engine head to the
> > > firewall.
> > >
> > > If you follow the headlight wiring, at the end near one light you will
> > > find a black wire bolted to the fender or grill. This is the main
> > > ground.
> > >
> > > The headlight switch has a ground wire under the dash near the steering
> > > column.
> > >
> > > Mike
> > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > 88 Cherokee 235 BFG AT's
> > >
> > > Davey wrote:
> > > >
> > > > Please, anyone can help me?
> > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > beam only) they start flickering and then off, only parking lights stay.
> > > > After one minute of waiting , i pull the switch again and lights are back
> > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > jack and connected everything directly on place but problem is still there.
> > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > problem.
> > > > If anyone has any idea please help.
> > > > Thanks
> > > > Davey
> > >
>
#22
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
It takes a pile of heat to pop them, usually enough to melt things and
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
#23
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
It takes a pile of heat to pop them, usually enough to melt things and
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
#24
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
It takes a pile of heat to pop them, usually enough to melt things and
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
#25
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
It takes a pile of heat to pop them, usually enough to melt things and
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
the wires are 10 ga. so that is a serious draw.
Mike
Lee Ayrton wrote:
>
> On Fri, 2 Apr 2004, Mike Romain wrote:
>
> > I am thinking the same thing and I was implying once tripped, the
> > breaker will never be stable again.
>
> I hadn't known that about automotive breakers, but I should have guessed,
> thanks for the tip. Regular AC breakers get weak if they get cycled, but
> it takes quite a few cycles to soften them up to the point that you'll
> notice.
>
> > I was thinking he tripped the new one before he cleaned up the wires
> > maybe?
>
> Dunno. I'm hoping that he comes back and gives us more detail.
>
> > Lee Ayrton wrote:
> > >
> > > The clue that I twigged on was "connection on headlamp switch (tan colour
> > > wire) was a little bit melted". Something made that connection hot,
> > > either over-load or corrosion. He says that he's replaced both the light
> > > switch and the headlamp dimmer switch, it would be good to know if this
> > > problem was the reason he changed out the switches or if there was
> > > something else going on. Either way it sounds like he's tripping the
> > > breaker, it doesn't seem likely that a bad ground is going to cause that.
> > >
> > > On Thu, 1 Apr 2004, Mike Romain wrote:
> > >
> > > > Do you have aftermarket bulbs in the lights?
> > > >
> > > > If the lights draw too many amps without a relay, they will blow a
> > > > circuit breaker inside the headlight switch. Once this breaker has been
> > > > popped, it doesn't ever hold full power after.
> > > >
> > > > The main ground is a wire mesh strap from the engine head to the
> > > > firewall.
> > > >
> > > > If you follow the headlight wiring, at the end near one light you will
> > > > find a black wire bolted to the fender or grill. This is the main
> > > > ground.
> > > >
> > > > The headlight switch has a ground wire under the dash near the steering
> > > > column.
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > Davey wrote:
> > > > >
> > > > > Please, anyone can help me?
> > > > > Every time after about 30 minutes of driving with headlights on (even low
> > > > > beam only) they start flickering and then off, only parking lights stay.
> > > > > After one minute of waiting , i pull the switch again and lights are back
> > > > > till... this is driving me nuts. Headlamp switch is new, ''dimmer switch''
> > > > > (high-low beam) is new, nothing wrong in lamps. Connection for headlights on
> > > > > headlamp switch (Tan colour wire) was little bit melted so I remove this
> > > > > jack and connected everything directly on place but problem is still there.
> > > > > I don't know where is ground connection for headlamps, maybe there is a
> > > > > problem.
> > > > > If anyone has any idea please help.
> > > > > Thanks
> > > > > Davey
> > > >
> >
#26
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
Here I am.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
#27
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
Here I am.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
#28
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
Here I am.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
#29
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
Here I am.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
I 've just checked everything again and like Mike said, on left inner fender
I found ground connections - three of them, little lower down just near left
headlight - a bunch of connections and removed all of this, cleaned
everything (with good old WD40) and tried to drive around almost half night.
Nothing happened. Seems OK.
Now I remember after one hard day for my rig somewhere in very muddy
terrain I washed Jeep underneath and engine also (mud was everywhere), maybe
some connections were corroded or, I don't know... I'll see next few days
what will be but seems that everything is fine.
One more question: This wire mesh strap which is hanging from firewall
should be connected somewhere on cylinder head? I found it just hanging, not
connected. Now it is temporary bolted on intake manifold. Probably previous
owner forgot to connect again after doing some repairs. Seems to me like I
can connect this back on bolt which holds fuel rail. I couldn't find any
other ground connection from engine to chassis, strange.
Anyway, thank you very much for advices, many greetings from far Croatia.
#30
Guest
Posts: n/a
Re: Headlights problem on XJ 1992
Davey did pass the time by typing:
> One more question: This wire mesh strap which is hanging from firewall
> should be connected somewhere on cylinder head? I found it just hanging, not
> connected. Now it is temporary bolted on intake manifold. Probably previous
> owner forgot to connect again after doing some repairs. Seems to me like I
> can connect this back on bolt which holds fuel rail. I couldn't find any
> other ground connection from engine to chassis, strange.
> Anyway, thank you very much for advices, many greetings from far Croatia.
That's your engine ground strap. Without it your engine gets it's ground
through the drivetrain and that can cause all sorts of sensor problems, rough
idle, etc. It goes back to the block. On the 93ZJ it uses the same bolt
that holds on the ignition coil, not sure about the 92 XJ.
--
DougW
> One more question: This wire mesh strap which is hanging from firewall
> should be connected somewhere on cylinder head? I found it just hanging, not
> connected. Now it is temporary bolted on intake manifold. Probably previous
> owner forgot to connect again after doing some repairs. Seems to me like I
> can connect this back on bolt which holds fuel rail. I couldn't find any
> other ground connection from engine to chassis, strange.
> Anyway, thank you very much for advices, many greetings from far Croatia.
That's your engine ground strap. Without it your engine gets it's ground
through the drivetrain and that can cause all sorts of sensor problems, rough
idle, etc. It goes back to the block. On the 93ZJ it uses the same bolt
that holds on the ignition coil, not sure about the 92 XJ.
--
DougW