FS: AMC 304 Engines and Parts
02-27-2006, 09:56 AM
#1
Guest
Posts: n/a
FS: AMC 304 Engines and Parts
I am selling two AMC 304's. One has popped. Piston shattered but there
appears to be no apparent scoring on cylinder wall. This engine had
about 30K on reman. It was running in my jeep till then. The other has
about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
running in my jeep till I swapped for the other. this engine had some
blow by on the #1 cylinder that is all. I have all stock parts to build
one of these but exhaust manifold. On top of that, I have a brand new
with only 15 minutes of run time, AMC performer intake (NON EGR) and a
brand new Edelbrock 1406 carb for this engine. This intake has
everything on it from the stock manifold and is ready to bolt on. I am
keeping my fan, but everything else should be there. Comes with
altenator, and power steering pump as well. Started I used as a core
charge for the 350 starter I bought for the swap I just did. Comes with
bell housing as well. The two engines with stock parts I will sell for
$175, and the upgrades which include the carb, intake and a set of
inframe hedman hedders will sell for $450. The hedders are not the
coated ones so they rust, but are in great shape. Not bent, dinged or
warped. If somone wants all of it, I will let it go for $600. The blown
engine is not in a crate with one head off, but it is garaged, the
other block is in a crate that has been covered and oiled. Email me at
drwoodberry@hotmail.com if you are interested in any or all of this.
Thanks so much.
appears to be no apparent scoring on cylinder wall. This engine had
about 30K on reman. It was running in my jeep till then. The other has
about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
running in my jeep till I swapped for the other. this engine had some
blow by on the #1 cylinder that is all. I have all stock parts to build
one of these but exhaust manifold. On top of that, I have a brand new
with only 15 minutes of run time, AMC performer intake (NON EGR) and a
brand new Edelbrock 1406 carb for this engine. This intake has
everything on it from the stock manifold and is ready to bolt on. I am
keeping my fan, but everything else should be there. Comes with
altenator, and power steering pump as well. Started I used as a core
charge for the 350 starter I bought for the swap I just did. Comes with
bell housing as well. The two engines with stock parts I will sell for
$175, and the upgrades which include the carb, intake and a set of
inframe hedman hedders will sell for $450. The hedders are not the
coated ones so they rust, but are in great shape. Not bent, dinged or
warped. If somone wants all of it, I will let it go for $600. The blown
engine is not in a crate with one head off, but it is garaged, the
other block is in a crate that has been covered and oiled. Email me at
drwoodberry@hotmail.com if you are interested in any or all of this.
Thanks so much.
02-27-2006, 10:44 AM
#2
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
And where is all this located?
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
02-27-2006, 10:44 AM
#3
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
And where is all this located?
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
02-27-2006, 10:44 AM
#4
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
And where is all this located?
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
02-27-2006, 10:44 AM
#5
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
And where is all this located?
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
drwoodberry@hotmail.com wrote:
> I am selling two AMC 304's. One has popped. Piston shattered but there
> appears to be no apparent scoring on cylinder wall. This engine had
> about 30K on reman. It was running in my jeep till then. The other has
> about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> running in my jeep till I swapped for the other. this engine had some
> blow by on the #1 cylinder that is all. I have all stock parts to build
> one of these but exhaust manifold. On top of that, I have a brand new
> with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> brand new Edelbrock 1406 carb for this engine. This intake has
> everything on it from the stock manifold and is ready to bolt on. I am
> keeping my fan, but everything else should be there. Comes with
> altenator, and power steering pump as well. Started I used as a core
> charge for the 350 starter I bought for the swap I just did. Comes with
> bell housing as well. The two engines with stock parts I will sell for
> $175, and the upgrades which include the carb, intake and a set of
> inframe hedman hedders will sell for $450. The hedders are not the
> coated ones so they rust, but are in great shape. Not bent, dinged or
> warped. If somone wants all of it, I will let it go for $600. The blown
> engine is not in a crate with one head off, but it is garaged, the
> other block is in a crate that has been covered and oiled. Email me at
> drwoodberry@hotmail.com if you are interested in any or all of this.
>
> Thanks so much.
>
03-13-2006, 11:50 AM
#6
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
Everything is located at Lake Anna, VA.
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
03-13-2006, 11:50 AM
#7
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
Everything is located at Lake Anna, VA.
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
03-13-2006, 11:50 AM
#8
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
Everything is located at Lake Anna, VA.
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
03-13-2006, 11:50 AM
#9
Guest
Posts: n/a
Re: FS: AMC 304 Engines and Parts
Everything is located at Lake Anna, VA.
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
RoyJ wrote:
> And where is all this located?
>
> drwoodberry@hotmail.com wrote:
>
> > I am selling two AMC 304's. One has popped. Piston shattered but there
> > appears to be no apparent scoring on cylinder wall. This engine had
> > about 30K on reman. It was running in my jeep till then. The other has
> > about 60K on rebuild. It is .030 over. Has nice crane cam in it. It was
> > running in my jeep till I swapped for the other. this engine had some
> > blow by on the #1 cylinder that is all. I have all stock parts to build
> > one of these but exhaust manifold. On top of that, I have a brand new
> > with only 15 minutes of run time, AMC performer intake (NON EGR) and a
> > brand new Edelbrock 1406 carb for this engine. This intake has
> > everything on it from the stock manifold and is ready to bolt on. I am
> > keeping my fan, but everything else should be there. Comes with
> > altenator, and power steering pump as well. Started I used as a core
> > charge for the 350 starter I bought for the swap I just did. Comes with
> > bell housing as well. The two engines with stock parts I will sell for
> > $175, and the upgrades which include the carb, intake and a set of
> > inframe hedman hedders will sell for $450. The hedders are not the
> > coated ones so they rust, but are in great shape. Not bent, dinged or
> > warped. If somone wants all of it, I will let it go for $600. The blown
> > engine is not in a crate with one head off, but it is garaged, the
> > other block is in a crate that has been covered and oiled. Email me at
> > drwoodberry@hotmail.com if you are interested in any or all of this.
> >
> > Thanks so much.
> >
Thread
Thread Starter
Forum
Replies
Last Post
William Oliveri
Jeep Mailing List
66
02-09-2004 10:13 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)