front bumper license plate mount hardware?
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
> >
> > Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> > plate out a bit. Put it dead center.
> >
> > I had been intending to use bolts secured from behind with nuts, but
> > there is a tubular reinforcment in the center of the bumper that makes
> > that difficult or impossible. So I just used the screws themselves.
> >
> > Mounting on the left or right side would require drilling the plate, as
> > the rubber bumper guards don't allow the plate to fit over the holes
> > properly.
I put mine on the front left with a cheapo kit from NAPA..but even
their cheap kit was solid black stainless steel, for $5.99, unlike the
dealer's plastic one for $40 or whatever. It fit on the side by
putting one screw in a high hole and one in a low. 2 screws seemed
like enough.
Matt
> > Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> > plate out a bit. Put it dead center.
> >
> > I had been intending to use bolts secured from behind with nuts, but
> > there is a tubular reinforcment in the center of the bumper that makes
> > that difficult or impossible. So I just used the screws themselves.
> >
> > Mounting on the left or right side would require drilling the plate, as
> > the rubber bumper guards don't allow the plate to fit over the holes
> > properly.
I put mine on the front left with a cheapo kit from NAPA..but even
their cheap kit was solid black stainless steel, for $5.99, unlike the
dealer's plastic one for $40 or whatever. It fit on the side by
putting one screw in a high hole and one in a low. 2 screws seemed
like enough.
Matt
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
> >
> > Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> > plate out a bit. Put it dead center.
> >
> > I had been intending to use bolts secured from behind with nuts, but
> > there is a tubular reinforcment in the center of the bumper that makes
> > that difficult or impossible. So I just used the screws themselves.
> >
> > Mounting on the left or right side would require drilling the plate, as
> > the rubber bumper guards don't allow the plate to fit over the holes
> > properly.
I put mine on the front left with a cheapo kit from NAPA..but even
their cheap kit was solid black stainless steel, for $5.99, unlike the
dealer's plastic one for $40 or whatever. It fit on the side by
putting one screw in a high hole and one in a low. 2 screws seemed
like enough.
Matt
> > Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> > plate out a bit. Put it dead center.
> >
> > I had been intending to use bolts secured from behind with nuts, but
> > there is a tubular reinforcment in the center of the bumper that makes
> > that difficult or impossible. So I just used the screws themselves.
> >
> > Mounting on the left or right side would require drilling the plate, as
> > the rubber bumper guards don't allow the plate to fit over the holes
> > properly.
I put mine on the front left with a cheapo kit from NAPA..but even
their cheap kit was solid black stainless steel, for $5.99, unlike the
dealer's plastic one for $40 or whatever. It fit on the side by
putting one screw in a high hole and one in a low. 2 screws seemed
like enough.
Matt
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
> >
> > Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> > plate out a bit. Put it dead center.
> >
> > I had been intending to use bolts secured from behind with nuts, but
> > there is a tubular reinforcment in the center of the bumper that makes
> > that difficult or impossible. So I just used the screws themselves.
> >
> > Mounting on the left or right side would require drilling the plate, as
> > the rubber bumper guards don't allow the plate to fit over the holes
> > properly.
I put mine on the front left with a cheapo kit from NAPA..but even
their cheap kit was solid black stainless steel, for $5.99, unlike the
dealer's plastic one for $40 or whatever. It fit on the side by
putting one screw in a high hole and one in a low. 2 screws seemed
like enough.
Matt
> > Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> > plate out a bit. Put it dead center.
> >
> > I had been intending to use bolts secured from behind with nuts, but
> > there is a tubular reinforcment in the center of the bumper that makes
> > that difficult or impossible. So I just used the screws themselves.
> >
> > Mounting on the left or right side would require drilling the plate, as
> > the rubber bumper guards don't allow the plate to fit over the holes
> > properly.
I put mine on the front left with a cheapo kit from NAPA..but even
their cheap kit was solid black stainless steel, for $5.99, unlike the
dealer's plastic one for $40 or whatever. It fit on the side by
putting one screw in a high hole and one in a low. 2 screws seemed
like enough.
Matt
Thread
Thread Starter
Forum
Replies
Last Post
olliebamino
Jeep JK Forum
1
Sep 10, 2010 09:30 PM
Handywired
Jeep Mailing List
0
Feb 3, 2004 12:32 AM
L.W.(=?iso-8859-1?Q?=DFill?=) Hughes III
Jeep Mailing List
2
Sep 15, 2003 05:53 PM
Jerry Bransford
Jeep Mailing List
0
Sep 15, 2003 12:49 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
