front bumper license plate mount hardware?
02-21-2004, 11:12 AM
#1
Guest
Posts: n/a
front bumper license plate mount hardware?
All,
I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
However, it is not clear how to mount the plate on the front bumper -
there is no license plate holder of any kind.
Is there an aftermarket license plate bracket/kit that anyone can recommend?
Thanks!
02-21-2004, 05:26 PM
#2
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
It's an option "MDAS Bracket - Front License Plate" If you don't
want to see the Stealership, than use the short quarter inch sheet metal
screws sold as license plate bolts at auto any parts store, and screw it
to your rubber baby bumper.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> All,
>
> I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
> However, it is not clear how to mount the plate on the front bumper -
> there is no license plate holder of any kind.
>
> Is there an aftermarket license plate bracket/kit that anyone can recommend?
>
> Thanks!
want to see the Stealership, than use the short quarter inch sheet metal
screws sold as license plate bolts at auto any parts store, and screw it
to your rubber baby bumper.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> All,
>
> I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
> However, it is not clear how to mount the plate on the front bumper -
> there is no license plate holder of any kind.
>
> Is there an aftermarket license plate bracket/kit that anyone can recommend?
>
> Thanks!
02-21-2004, 05:26 PM
#3
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
It's an option "MDAS Bracket - Front License Plate" If you don't
want to see the Stealership, than use the short quarter inch sheet metal
screws sold as license plate bolts at auto any parts store, and screw it
to your rubber baby bumper.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> All,
>
> I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
> However, it is not clear how to mount the plate on the front bumper -
> there is no license plate holder of any kind.
>
> Is there an aftermarket license plate bracket/kit that anyone can recommend?
>
> Thanks!
want to see the Stealership, than use the short quarter inch sheet metal
screws sold as license plate bolts at auto any parts store, and screw it
to your rubber baby bumper.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> All,
>
> I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
> However, it is not clear how to mount the plate on the front bumper -
> there is no license plate holder of any kind.
>
> Is there an aftermarket license plate bracket/kit that anyone can recommend?
>
> Thanks!
02-21-2004, 05:26 PM
#4
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
It's an option "MDAS Bracket - Front License Plate" If you don't
want to see the Stealership, than use the short quarter inch sheet metal
screws sold as license plate bolts at auto any parts store, and screw it
to your rubber baby bumper.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> All,
>
> I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
> However, it is not clear how to mount the plate on the front bumper -
> there is no license plate holder of any kind.
>
> Is there an aftermarket license plate bracket/kit that anyone can recommend?
>
> Thanks!
want to see the Stealership, than use the short quarter inch sheet metal
screws sold as license plate bolts at auto any parts store, and screw it
to your rubber baby bumper.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> All,
>
> I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
> However, it is not clear how to mount the plate on the front bumper -
> there is no license plate holder of any kind.
>
> Is there an aftermarket license plate bracket/kit that anyone can recommend?
>
> Thanks!
02-21-2004, 05:40 PM
#5
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
Yeah, I ended up using 8mm by 25mm screws with some washers to space the
plate out a bit. Put it dead center.
I had been intending to use bolts secured from behind with nuts, but
there is a tubular reinforcment in the center of the bumper that makes
that difficult or impossible. So I just used the screws themselves.
Mounting on the left or right side would require drilling the plate, as
the rubber bumper guards don't allow the plate to fit over the holes
properly.
L.W.(ßill) ------ III wrote:
> It's an option "MDAS Bracket - Front License Plate" If you don't
> want to see the Stealership, than use the short quarter inch sheet metal
> screws sold as license plate bolts at auto any parts store, and screw it
> to your rubber baby bumper.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> thomas wrote:
>
>>All,
>>
>>I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
>>However, it is not clear how to mount the plate on the front bumper -
>>there is no license plate holder of any kind.
>>
>>Is there an aftermarket license plate bracket/kit that anyone can recommend?
>>
>>Thanks!
02-21-2004, 05:40 PM
#6
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
Yeah, I ended up using 8mm by 25mm screws with some washers to space the
plate out a bit. Put it dead center.
I had been intending to use bolts secured from behind with nuts, but
there is a tubular reinforcment in the center of the bumper that makes
that difficult or impossible. So I just used the screws themselves.
Mounting on the left or right side would require drilling the plate, as
the rubber bumper guards don't allow the plate to fit over the holes
properly.
L.W.(ßill) ------ III wrote:
> It's an option "MDAS Bracket - Front License Plate" If you don't
> want to see the Stealership, than use the short quarter inch sheet metal
> screws sold as license plate bolts at auto any parts store, and screw it
> to your rubber baby bumper.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> thomas wrote:
>
>>All,
>>
>>I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
>>However, it is not clear how to mount the plate on the front bumper -
>>there is no license plate holder of any kind.
>>
>>Is there an aftermarket license plate bracket/kit that anyone can recommend?
>>
>>Thanks!
02-21-2004, 05:40 PM
#7
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
Yeah, I ended up using 8mm by 25mm screws with some washers to space the
plate out a bit. Put it dead center.
I had been intending to use bolts secured from behind with nuts, but
there is a tubular reinforcment in the center of the bumper that makes
that difficult or impossible. So I just used the screws themselves.
Mounting on the left or right side would require drilling the plate, as
the rubber bumper guards don't allow the plate to fit over the holes
properly.
L.W.(ßill) ------ III wrote:
> It's an option "MDAS Bracket - Front License Plate" If you don't
> want to see the Stealership, than use the short quarter inch sheet metal
> screws sold as license plate bolts at auto any parts store, and screw it
> to your rubber baby bumper.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> thomas wrote:
>
>>All,
>>
>>I've an 03 Wrangler. Just yesterday, I got my plates from the DMV.
>>However, it is not clear how to mount the plate on the front bumper -
>>there is no license plate holder of any kind.
>>
>>Is there an aftermarket license plate bracket/kit that anyone can recommend?
>>
>>Thanks!
02-21-2004, 05:57 PM
#8
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
Sounds like you solved the problem to me.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> plate out a bit. Put it dead center.
>
> I had been intending to use bolts secured from behind with nuts, but
> there is a tubular reinforcment in the center of the bumper that makes
> that difficult or impossible. So I just used the screws themselves.
>
> Mounting on the left or right side would require drilling the plate, as
> the rubber bumper guards don't allow the plate to fit over the holes
> properly.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> plate out a bit. Put it dead center.
>
> I had been intending to use bolts secured from behind with nuts, but
> there is a tubular reinforcment in the center of the bumper that makes
> that difficult or impossible. So I just used the screws themselves.
>
> Mounting on the left or right side would require drilling the plate, as
> the rubber bumper guards don't allow the plate to fit over the holes
> properly.
02-21-2004, 05:57 PM
#9
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
Sounds like you solved the problem to me.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> plate out a bit. Put it dead center.
>
> I had been intending to use bolts secured from behind with nuts, but
> there is a tubular reinforcment in the center of the bumper that makes
> that difficult or impossible. So I just used the screws themselves.
>
> Mounting on the left or right side would require drilling the plate, as
> the rubber bumper guards don't allow the plate to fit over the holes
> properly.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> plate out a bit. Put it dead center.
>
> I had been intending to use bolts secured from behind with nuts, but
> there is a tubular reinforcment in the center of the bumper that makes
> that difficult or impossible. So I just used the screws themselves.
>
> Mounting on the left or right side would require drilling the plate, as
> the rubber bumper guards don't allow the plate to fit over the holes
> properly.
02-21-2004, 05:57 PM
#10
Guest
Posts: n/a
Re: front bumper license plate mount hardware?
Sounds like you solved the problem to me.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> plate out a bit. Put it dead center.
>
> I had been intending to use bolts secured from behind with nuts, but
> there is a tubular reinforcment in the center of the bumper that makes
> that difficult or impossible. So I just used the screws themselves.
>
> Mounting on the left or right side would require drilling the plate, as
> the rubber bumper guards don't allow the plate to fit over the holes
> properly.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
thomas wrote:
>
> Yeah, I ended up using 8mm by 25mm screws with some washers to space the
> plate out a bit. Put it dead center.
>
> I had been intending to use bolts secured from behind with nuts, but
> there is a tubular reinforcment in the center of the bumper that makes
> that difficult or impossible. So I just used the screws themselves.
>
> Mounting on the left or right side would require drilling the plate, as
> the rubber bumper guards don't allow the plate to fit over the holes
> properly.
