Ford axle ? for Bill, or anyone
07-27-2005, 07:02 PM
#1
Guest
Posts: n/a
Ford axle ? for Bill, or anyone
Is a ford 9" a ford 9" when it comes to axle seals, or are they different
for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
Torino, axle seal is leaking quite bad, but as I'm not completely sure what
vehicle it is out of, I just wondered if they are all the same.
for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
Torino, axle seal is leaking quite bad, but as I'm not completely sure what
vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 07:58 PM
#2
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Hi Greg,
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 07:58 PM
#3
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Hi Greg,
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 07:58 PM
#4
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Hi Greg,
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 07:58 PM
#5
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Hi Greg,
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
Many different sizes of axles, bearings, and seals. The Torino
would be a good place to start. Third member identification:
http://web.archive.org/web/200303240...m/ninecase.htm
But more than likely the cut axles will be 31 or 33 spline, but with the
Torino type passenger car single roller bearing, like mine:
http://www.----------.com/9axle.jpg with stock seal.
God Bless America, ßill O|||||||O
mailto:--------------------
Greg wrote:
>
> Is a ford 9" a ford 9" when it comes to axle seals, or are they different
> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a 63
> Torino, axle seal is leaking quite bad, but as I'm not completely sure what
> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 09:14 PM
#6
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Axles are full length, not cut, 31 spline, third member is out of 79
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 09:14 PM
#7
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Axles are full length, not cut, 31 spline, third member is out of 79
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 09:14 PM
#8
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Axles are full length, not cut, 31 spline, third member is out of 79
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
07-27-2005, 09:14 PM
#9
Guest
Posts: n/a
Re: Ford axle ? for Bill, or anyone
Axles are full length, not cut, 31 spline, third member is out of 79
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
econoline so that doesn't help us much, on curries site,
http://www.currieenterprises.com/ces...re.aspx?id=938 , I find 4
axle seals, large bearing, small bearing, large tapered bearing and 45mm
bearing, the 45mm is for 35-40 spline so not that, but I can't remeber if
her's were tappered or not, or if I would know a tapered one if I saw it, it
did look like your pic though.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:42E81FA3.5E007071@***.net...
> Hi Greg,
> Many different sizes of axles, bearings, and seals. The Torino
> would be a good place to start. Third member identification:
> http://web.archive.org/web/200303240...m/ninecase.htm
> But more than likely the cut axles will be 31 or 33 spline, but with the
> Torino type passenger car single roller bearing, like mine:
> http://www.----------.com/9axle.jpg with stock seal.
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Greg wrote:
>>
>> Is a ford 9" a ford 9" when it comes to axle seals, or are they
>> different
>> for years and aplication, daughter's 9" in her YJ is out of, I beleive, a
>> 63
>> Torino, axle seal is leaking quite bad, but as I'm not completely sure
>> what
>> vehicle it is out of, I just wondered if they are all the same.
Thread
Thread Starter
Forum
Replies
Last Post
Derek Proctor
Jeep Mailing List
92
08-16-2004 04:33 PM
L.W.(=?iso-8859-1?Q?=DFill?=) Hughes III
Jeep Mailing List
36
04-02-2004 12:19 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)