If anyone remembers I had a freind coming over to do lift kit and fix his
skid plate that fell off, 10 miles up in the bush of coarse, to get out of
bush it was a little cable hand winch, over frame, under tranny, over other
frame, and hook onto skid plate, cranked it back up, drove out fine.
Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
frame were about 5/8th dia. so I widened one round side out to a square like
the following
___
(___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
the unit up into frame with nut up, screwed a new bolt in to hold it in
place and align it, then tacked it with welder, unscrewed bolt, completed
weld, a little grinding to flatten out, and good as new. Did the other 2 on
that side, for some reason all 3 of drivers side came out OK.
So total working time for one side, with skid already off, was about 30
minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
3 new 1/2" by whatever you need bolts, so total cost if you have access to a
welder is about 20 cents.
Feel free to ask how I fixed the 3" of frame on both sides of the front
that was rusted through, gotta love it when freind comes over to get you to
help with lift kit and while doing the front we see that steering box is
only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
that part of frame opens and closes 1/4".

 

That sounded like a nice strong and painless fix. Thanks for the follow
up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

That sounded like a nice strong and painless fix. Thanks for the follow
up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

That sounded like a nice strong and painless fix. Thanks for the follow
up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

That sounded like a nice strong and painless fix. Thanks for the follow
up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

Real Jeepers, simply hold the new nut to the inside of the channel
frame like the big boys still use:
http://www.----------.com/temp/fordF650.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

Real Jeepers, simply hold the new nut to the inside of the channel
frame like the big boys still use:
http://www.----------.com/temp/fordF650.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

Real Jeepers, simply hold the new nut to the inside of the channel
frame like the big boys still use:
http://www.----------.com/temp/fordF650.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

Real Jeepers, simply hold the new nut to the inside of the channel
frame like the big boys still use:
http://www.----------.com/temp/fordF650.jpg
God Bless America, Bill O|||||||O
mailto:--------------------

Greg wrote:
>
> If anyone remembers I had a freind coming over to do lift kit and fix his
> skid plate that fell off, 10 miles up in the bush of coarse, to get out of
> bush it was a little cable hand winch, over frame, under tranny, over other
> frame, and hook onto skid plate, cranked it back up, drove out fine.
> Anyway so I was to fix skid plate bolts, 88 YJ, so of coarse nuts that are
> in frame were busted off, so my fix, ( sorry Bill, no pics ). The 3 holes in
> frame were about 5/8th dia. so I widened one round side out to a square like
> the following
> ___
> (___! so now it was about 5/8 x 3/4, I then cut a peice of 1/4" flat bar
> 3/4 x 2", drilled a hole in it, welded a 1/2" nut to top, ( which is 3/4"
> outside ) ran a 1/2" tap through nut and right through 1/4" plate, then slid
> the unit up into frame with nut up, screwed a new bolt in to hold it in
> place and align it, then tacked it with welder, unscrewed bolt, completed
> weld, a little grinding to flatten out, and good as new. Did the other 2 on
> that side, for some reason all 3 of drivers side came out OK.
> So total working time for one side, with skid already off, was about 30
> minutes, needed were welder, ( I have a lincoln mig 10, perfect for this
> kind of thing ), angle grinder, 6" of 3/4 x 1/4" flat stock, 3 - 1/2" nuts,
> 3 new 1/2" by whatever you need bolts, so total cost if you have access to a
> welder is about 20 cents.
> Feel free to ask how I fixed the 3" of frame on both sides of the front
> that was rusted through, gotta love it when freind comes over to get you to
> help with lift kit and while doing the front we see that steering box is
> only held on with the 2 bolts in bottom of frame, and if you turn the wheel,
> that part of frame opens and closes 1/4".

 

> Real Jeepers, simply hold the new nut to the inside of the channel

Jeepster has a boxed frame, and the cherokee frame will be that way when i'm
done with it.

--
Stupendous Man,
Defender of Freedom, Advocate of Liberty