Sounds like you mixed them up. More than likely they will fail. Buy
a new set.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/

William Oliveri wrote:
>
> No, just changed position from what they previously were.

 

Sounds like you mixed them up. More than likely they will fail. Buy
a new set.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/

William Oliveri wrote:
>
> No, just changed position from what they previously were.

 

Just a thought. Can't remember if you said you'd replaced the lifters.
If you changed the lifters, did you prime 'em before putting them in?
o_o_o_o
Best Regards, /| ,[_____],
Jim, WP3JQ |ŻŻŻL --O|||||||O-
()_)Ż()_) ŻŻŻŻŻ )_)
EM60qk 30.447439N 086.628959W
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bv9qpc$lh8nm$1@ID-193866.news.uni-berlin.de...
> I completed one cylinder replacing the valve seals and decided to put the
> valve cover back on after torqueing down the rocker arms on my 4.2L
engine.
> I wanted to see if I could tell a difference in this cylinder spark plug
> wise after the change.
>
> Anyway, I'm now hearing a clacking noise when the engine is running. I
> remembered what someone said about replacing the right components back in
> the right place so I took the valve cover back off and changed the rocker
> arms around. This seemed to make the sound better but it's still not
> sounding good.
>
>
> Any ideas on this?
>
> Thank you,
>
> Bill
>
>

 

Just a thought. Can't remember if you said you'd replaced the lifters.
If you changed the lifters, did you prime 'em before putting them in?
o_o_o_o
Best Regards, /| ,[_____],
Jim, WP3JQ |ŻŻŻL --O|||||||O-
()_)Ż()_) ŻŻŻŻŻ )_)
EM60qk 30.447439N 086.628959W
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bv9qpc$lh8nm$1@ID-193866.news.uni-berlin.de...
> I completed one cylinder replacing the valve seals and decided to put the
> valve cover back on after torqueing down the rocker arms on my 4.2L
engine.
> I wanted to see if I could tell a difference in this cylinder spark plug
> wise after the change.
>
> Anyway, I'm now hearing a clacking noise when the engine is running. I
> remembered what someone said about replacing the right components back in
> the right place so I took the valve cover back off and changed the rocker
> arms around. This seemed to make the sound better but it's still not
> sounding good.
>
>
> Any ideas on this?
>
> Thank you,
>
> Bill
>
>

 

Just a thought. Can't remember if you said you'd replaced the lifters.
If you changed the lifters, did you prime 'em before putting them in?
o_o_o_o
Best Regards, /| ,[_____],
Jim, WP3JQ |ŻŻŻL --O|||||||O-
()_)Ż()_) ŻŻŻŻŻ )_)
EM60qk 30.447439N 086.628959W
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bv9qpc$lh8nm$1@ID-193866.news.uni-berlin.de...
> I completed one cylinder replacing the valve seals and decided to put the
> valve cover back on after torqueing down the rocker arms on my 4.2L
engine.
> I wanted to see if I could tell a difference in this cylinder spark plug
> wise after the change.
>
> Anyway, I'm now hearing a clacking noise when the engine is running. I
> remembered what someone said about replacing the right components back in
> the right place so I took the valve cover back off and changed the rocker
> arms around. This seemed to make the sound better but it's still not
> sounding good.
>
>
> Any ideas on this?
>
> Thank you,
>
> Bill
>
>