I have a 1997 Jeep Wrangler Sport, and my check engine light came
on with 2 different codes. The codes were 43, and 42. I disconnected
the battery to clear it, and the light came on again the next day with
error code 43 again. My Jeep still runs great, but I have noticed my
gas guage will be fine on minute, then suddenly it will go to empty. If
I turn my engine off for a couple of minutes then start it back up
again the guage will be fine again. Any suggestions? I'd appreciate any
input....

Thanks in advance,
Jon

 

http://minimopar.knizefamily.net/fault/code42-SMEC.html
http://minimopar.knizefamily.net/fault/code43.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/

jongig wrote:
>
> I have a 1997 Jeep Wrangler Sport, and my check engine light came
> on with 2 different codes. The codes were 43, and 42. I disconnected
> the battery to clear it, and the light came on again the next day with
> error code 43 again. My Jeep still runs great, but I have noticed my
> gas guage will be fine on minute, then suddenly it will go to empty. If
> I turn my engine off for a couple of minutes then start it back up
> again the guage will be fine again. Any suggestions? I'd appreciate any
> input....
>
> Thanks in advance,
> Jon

 

http://minimopar.knizefamily.net/fault/code42-SMEC.html
http://minimopar.knizefamily.net/fault/code43.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/

jongig wrote:
>
> I have a 1997 Jeep Wrangler Sport, and my check engine light came
> on with 2 different codes. The codes were 43, and 42. I disconnected
> the battery to clear it, and the light came on again the next day with
> error code 43 again. My Jeep still runs great, but I have noticed my
> gas guage will be fine on minute, then suddenly it will go to empty. If
> I turn my engine off for a couple of minutes then start it back up
> again the guage will be fine again. Any suggestions? I'd appreciate any
> input....
>
> Thanks in advance,
> Jon

 

http://minimopar.knizefamily.net/fault/code42-SMEC.html
http://minimopar.knizefamily.net/fault/code43.html
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/

jongig wrote:
>
> I have a 1997 Jeep Wrangler Sport, and my check engine light came
> on with 2 different codes. The codes were 43, and 42. I disconnected
> the battery to clear it, and the light came on again the next day with
> error code 43 again. My Jeep still runs great, but I have noticed my
> gas guage will be fine on minute, then suddenly it will go to empty. If
> I turn my engine off for a couple of minutes then start it back up
> again the guage will be fine again. Any suggestions? I'd appreciate any
> input....
>
> Thanks in advance,
> Jon

 

Thanks for the reply, I guess I should check my coil. Anyone ever
had the same problem with the gas guage?

 

Thanks for the reply, I guess I should check my coil. Anyone ever
had the same problem with the gas guage?

 

Thanks for the reply, I guess I should check my coil. Anyone ever
had the same problem with the gas guage?

 

try going to autozone to pull the codes. I had code 43 also, replaced the
coil, but turned out to just need new plugs/wires. I'll bet you will get
cylinder missfire codes when connected to a code reader.
cal

"jongig" <jongig@verizon.net> wrote in message
news:1138678914.812054.240100@g43g2000cwa.googlegr oups.com...
>
> Thanks for the reply, I guess I should check my coil. Anyone ever
> had the same problem with the gas guage?
>

 

try going to autozone to pull the codes. I had code 43 also, replaced the
coil, but turned out to just need new plugs/wires. I'll bet you will get
cylinder missfire codes when connected to a code reader.
cal

"jongig" <jongig@verizon.net> wrote in message
news:1138678914.812054.240100@g43g2000cwa.googlegr oups.com...
>
> Thanks for the reply, I guess I should check my coil. Anyone ever
> had the same problem with the gas guage?
>

 

try going to autozone to pull the codes. I had code 43 also, replaced the
coil, but turned out to just need new plugs/wires. I'll bet you will get
cylinder missfire codes when connected to a code reader.
cal

"jongig" <jongig@verizon.net> wrote in message
news:1138678914.812054.240100@g43g2000cwa.googlegr oups.com...
>
> Thanks for the reply, I guess I should check my coil. Anyone ever
> had the same problem with the gas guage?
>