Correction on my earlier 2002 Wrangler post
08-22-2006, 11:45 AM
#11
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
There also is an issue with 'some' of the power connectors for the
blower motor on those models I hear.
I think I would be locating the motor, then trace the wires to the first
connection, likely within 8" of the motor and then be checking it for
heat with the fan on full and on the other speeds as well.
If heat is found there, then that could be the trouble. The pins inside
burn out and might just be not passing enough power for the lower speeds
to work.
That plug can just be cut out and bypassed using generic crimp on
connector sets.
Mike
billy ray wrote:
>
> In the '03 manual:
> The blower motor resistor is mounted to the bottom
>
> of the heater-A/C housing on the passenger side
>
> of the vehicle under the instrument panel. It can be
>
> accessed for service by removing the Instrument
>
> Panel glove box.
>
> FYI: The fan switch itself only controls the highest fan speed, the rest are
> controlled through the resistor pack. It is a common repair and it is (or
> should be) surprising that the parts counter man did not mention it....
>
> The resister pack will be about $15 at the dealership and take 15 minutes to
> install as Mike says.
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44EB188E.44CEFDE5@sympatico.ca...
> > There is a resistor pack that controls the lower speeds. 'Usually' all
> > 3 crap out, but I have seen just one or two go.
> >
> > On the older Wrangler Jeeps, this pack was located at the bottom of the
> > heater box in the passenger footwell, but I have been told the newer
> > boxes are different with the fan inside so I am not sure on those. It
> > will be stuck into the heater box though.
> >
> > And just FYI, the switch can be replaced by itself for about fifteen
> > bucks, you don't need the whole cluster. The parts guy just needs to
> > dig deeper.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > kwp wrote:
> >>
> >> I need some help, reader.
> >>
> >> A couple weeks ago, I posted that my fan was working on all 4 speed
> >> positions, but that my a/c was working on the top two positions only.
> >>
> >> This earlier post of mine was incorrect. Actually, the fan is only
> >> working on the top two positions. Consequently, the a/c only works on
> >> those positions, too.
> >>
> >> Can someone offer the fix to get this two lower fan speed settings to
> >> work? To date, my attempt to correct the problem was to replace the
> >> control panel/module (I figured the switch was bad), but this made no
> >> difference. The fan will still not work on the first two speed
> >> settings.
> >>
> >> Any advice appreciated!
blower motor on those models I hear.
I think I would be locating the motor, then trace the wires to the first
connection, likely within 8" of the motor and then be checking it for
heat with the fan on full and on the other speeds as well.
If heat is found there, then that could be the trouble. The pins inside
burn out and might just be not passing enough power for the lower speeds
to work.
That plug can just be cut out and bypassed using generic crimp on
connector sets.
Mike
billy ray wrote:
>
> In the '03 manual:
> The blower motor resistor is mounted to the bottom
>
> of the heater-A/C housing on the passenger side
>
> of the vehicle under the instrument panel. It can be
>
> accessed for service by removing the Instrument
>
> Panel glove box.
>
> FYI: The fan switch itself only controls the highest fan speed, the rest are
> controlled through the resistor pack. It is a common repair and it is (or
> should be) surprising that the parts counter man did not mention it....
>
> The resister pack will be about $15 at the dealership and take 15 minutes to
> install as Mike says.
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44EB188E.44CEFDE5@sympatico.ca...
> > There is a resistor pack that controls the lower speeds. 'Usually' all
> > 3 crap out, but I have seen just one or two go.
> >
> > On the older Wrangler Jeeps, this pack was located at the bottom of the
> > heater box in the passenger footwell, but I have been told the newer
> > boxes are different with the fan inside so I am not sure on those. It
> > will be stuck into the heater box though.
> >
> > And just FYI, the switch can be replaced by itself for about fifteen
> > bucks, you don't need the whole cluster. The parts guy just needs to
> > dig deeper.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > kwp wrote:
> >>
> >> I need some help, reader.
> >>
> >> A couple weeks ago, I posted that my fan was working on all 4 speed
> >> positions, but that my a/c was working on the top two positions only.
> >>
> >> This earlier post of mine was incorrect. Actually, the fan is only
> >> working on the top two positions. Consequently, the a/c only works on
> >> those positions, too.
> >>
> >> Can someone offer the fix to get this two lower fan speed settings to
> >> work? To date, my attempt to correct the problem was to replace the
> >> control panel/module (I figured the switch was bad), but this made no
> >> difference. The fan will still not work on the first two speed
> >> settings.
> >>
> >> Any advice appreciated!
08-22-2006, 11:45 AM
#12
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
There also is an issue with 'some' of the power connectors for the
blower motor on those models I hear.
I think I would be locating the motor, then trace the wires to the first
connection, likely within 8" of the motor and then be checking it for
heat with the fan on full and on the other speeds as well.
If heat is found there, then that could be the trouble. The pins inside
burn out and might just be not passing enough power for the lower speeds
to work.
That plug can just be cut out and bypassed using generic crimp on
connector sets.
Mike
billy ray wrote:
>
> In the '03 manual:
> The blower motor resistor is mounted to the bottom
>
> of the heater-A/C housing on the passenger side
>
> of the vehicle under the instrument panel. It can be
>
> accessed for service by removing the Instrument
>
> Panel glove box.
>
> FYI: The fan switch itself only controls the highest fan speed, the rest are
> controlled through the resistor pack. It is a common repair and it is (or
> should be) surprising that the parts counter man did not mention it....
>
> The resister pack will be about $15 at the dealership and take 15 minutes to
> install as Mike says.
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44EB188E.44CEFDE5@sympatico.ca...
> > There is a resistor pack that controls the lower speeds. 'Usually' all
> > 3 crap out, but I have seen just one or two go.
> >
> > On the older Wrangler Jeeps, this pack was located at the bottom of the
> > heater box in the passenger footwell, but I have been told the newer
> > boxes are different with the fan inside so I am not sure on those. It
> > will be stuck into the heater box though.
> >
> > And just FYI, the switch can be replaced by itself for about fifteen
> > bucks, you don't need the whole cluster. The parts guy just needs to
> > dig deeper.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > kwp wrote:
> >>
> >> I need some help, reader.
> >>
> >> A couple weeks ago, I posted that my fan was working on all 4 speed
> >> positions, but that my a/c was working on the top two positions only.
> >>
> >> This earlier post of mine was incorrect. Actually, the fan is only
> >> working on the top two positions. Consequently, the a/c only works on
> >> those positions, too.
> >>
> >> Can someone offer the fix to get this two lower fan speed settings to
> >> work? To date, my attempt to correct the problem was to replace the
> >> control panel/module (I figured the switch was bad), but this made no
> >> difference. The fan will still not work on the first two speed
> >> settings.
> >>
> >> Any advice appreciated!
blower motor on those models I hear.
I think I would be locating the motor, then trace the wires to the first
connection, likely within 8" of the motor and then be checking it for
heat with the fan on full and on the other speeds as well.
If heat is found there, then that could be the trouble. The pins inside
burn out and might just be not passing enough power for the lower speeds
to work.
That plug can just be cut out and bypassed using generic crimp on
connector sets.
Mike
billy ray wrote:
>
> In the '03 manual:
> The blower motor resistor is mounted to the bottom
>
> of the heater-A/C housing on the passenger side
>
> of the vehicle under the instrument panel. It can be
>
> accessed for service by removing the Instrument
>
> Panel glove box.
>
> FYI: The fan switch itself only controls the highest fan speed, the rest are
> controlled through the resistor pack. It is a common repair and it is (or
> should be) surprising that the parts counter man did not mention it....
>
> The resister pack will be about $15 at the dealership and take 15 minutes to
> install as Mike says.
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44EB188E.44CEFDE5@sympatico.ca...
> > There is a resistor pack that controls the lower speeds. 'Usually' all
> > 3 crap out, but I have seen just one or two go.
> >
> > On the older Wrangler Jeeps, this pack was located at the bottom of the
> > heater box in the passenger footwell, but I have been told the newer
> > boxes are different with the fan inside so I am not sure on those. It
> > will be stuck into the heater box though.
> >
> > And just FYI, the switch can be replaced by itself for about fifteen
> > bucks, you don't need the whole cluster. The parts guy just needs to
> > dig deeper.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > kwp wrote:
> >>
> >> I need some help, reader.
> >>
> >> A couple weeks ago, I posted that my fan was working on all 4 speed
> >> positions, but that my a/c was working on the top two positions only.
> >>
> >> This earlier post of mine was incorrect. Actually, the fan is only
> >> working on the top two positions. Consequently, the a/c only works on
> >> those positions, too.
> >>
> >> Can someone offer the fix to get this two lower fan speed settings to
> >> work? To date, my attempt to correct the problem was to replace the
> >> control panel/module (I figured the switch was bad), but this made no
> >> difference. The fan will still not work on the first two speed
> >> settings.
> >>
> >> Any advice appreciated!
08-22-2006, 11:45 AM
#13
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
There also is an issue with 'some' of the power connectors for the
blower motor on those models I hear.
I think I would be locating the motor, then trace the wires to the first
connection, likely within 8" of the motor and then be checking it for
heat with the fan on full and on the other speeds as well.
If heat is found there, then that could be the trouble. The pins inside
burn out and might just be not passing enough power for the lower speeds
to work.
That plug can just be cut out and bypassed using generic crimp on
connector sets.
Mike
billy ray wrote:
>
> In the '03 manual:
> The blower motor resistor is mounted to the bottom
>
> of the heater-A/C housing on the passenger side
>
> of the vehicle under the instrument panel. It can be
>
> accessed for service by removing the Instrument
>
> Panel glove box.
>
> FYI: The fan switch itself only controls the highest fan speed, the rest are
> controlled through the resistor pack. It is a common repair and it is (or
> should be) surprising that the parts counter man did not mention it....
>
> The resister pack will be about $15 at the dealership and take 15 minutes to
> install as Mike says.
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44EB188E.44CEFDE5@sympatico.ca...
> > There is a resistor pack that controls the lower speeds. 'Usually' all
> > 3 crap out, but I have seen just one or two go.
> >
> > On the older Wrangler Jeeps, this pack was located at the bottom of the
> > heater box in the passenger footwell, but I have been told the newer
> > boxes are different with the fan inside so I am not sure on those. It
> > will be stuck into the heater box though.
> >
> > And just FYI, the switch can be replaced by itself for about fifteen
> > bucks, you don't need the whole cluster. The parts guy just needs to
> > dig deeper.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > kwp wrote:
> >>
> >> I need some help, reader.
> >>
> >> A couple weeks ago, I posted that my fan was working on all 4 speed
> >> positions, but that my a/c was working on the top two positions only.
> >>
> >> This earlier post of mine was incorrect. Actually, the fan is only
> >> working on the top two positions. Consequently, the a/c only works on
> >> those positions, too.
> >>
> >> Can someone offer the fix to get this two lower fan speed settings to
> >> work? To date, my attempt to correct the problem was to replace the
> >> control panel/module (I figured the switch was bad), but this made no
> >> difference. The fan will still not work on the first two speed
> >> settings.
> >>
> >> Any advice appreciated!
blower motor on those models I hear.
I think I would be locating the motor, then trace the wires to the first
connection, likely within 8" of the motor and then be checking it for
heat with the fan on full and on the other speeds as well.
If heat is found there, then that could be the trouble. The pins inside
burn out and might just be not passing enough power for the lower speeds
to work.
That plug can just be cut out and bypassed using generic crimp on
connector sets.
Mike
billy ray wrote:
>
> In the '03 manual:
> The blower motor resistor is mounted to the bottom
>
> of the heater-A/C housing on the passenger side
>
> of the vehicle under the instrument panel. It can be
>
> accessed for service by removing the Instrument
>
> Panel glove box.
>
> FYI: The fan switch itself only controls the highest fan speed, the rest are
> controlled through the resistor pack. It is a common repair and it is (or
> should be) surprising that the parts counter man did not mention it....
>
> The resister pack will be about $15 at the dealership and take 15 minutes to
> install as Mike says.
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:44EB188E.44CEFDE5@sympatico.ca...
> > There is a resistor pack that controls the lower speeds. 'Usually' all
> > 3 crap out, but I have seen just one or two go.
> >
> > On the older Wrangler Jeeps, this pack was located at the bottom of the
> > heater box in the passenger footwell, but I have been told the newer
> > boxes are different with the fan inside so I am not sure on those. It
> > will be stuck into the heater box though.
> >
> > And just FYI, the switch can be replaced by itself for about fifteen
> > bucks, you don't need the whole cluster. The parts guy just needs to
> > dig deeper.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > kwp wrote:
> >>
> >> I need some help, reader.
> >>
> >> A couple weeks ago, I posted that my fan was working on all 4 speed
> >> positions, but that my a/c was working on the top two positions only.
> >>
> >> This earlier post of mine was incorrect. Actually, the fan is only
> >> working on the top two positions. Consequently, the a/c only works on
> >> those positions, too.
> >>
> >> Can someone offer the fix to get this two lower fan speed settings to
> >> work? To date, my attempt to correct the problem was to replace the
> >> control panel/module (I figured the switch was bad), but this made no
> >> difference. The fan will still not work on the first two speed
> >> settings.
> >>
> >> Any advice appreciated!
08-22-2006, 01:40 PM
#14
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
Okay, I just returned from my Jeep dealer, and the parts guy hooked me
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
08-22-2006, 01:40 PM
#15
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
Okay, I just returned from my Jeep dealer, and the parts guy hooked me
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
08-22-2006, 01:40 PM
#16
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
Okay, I just returned from my Jeep dealer, and the parts guy hooked me
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
08-22-2006, 01:40 PM
#17
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
Okay, I just returned from my Jeep dealer, and the parts guy hooked me
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
up with a resistor pack, which is a nice little part about the size of
a deck of cards. I'll see if I can install it this evening. Many
thanks, and I'll post the outcome.
08-22-2006, 08:32 PM
#18
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
http://www.----------.com/temp/TJresistor.pdf
God Bless America, Bill O|||||||O
mailto:--------------------
kwp wrote:
>
> Okay, I just returned from my Jeep dealer, and the parts guy hooked me
> up with a resistor pack, which is a nice little part about the size of
> a deck of cards. I'll see if I can install it this evening. Many
> thanks, and I'll post the outcome.
God Bless America, Bill O|||||||O
mailto:--------------------
kwp wrote:
>
> Okay, I just returned from my Jeep dealer, and the parts guy hooked me
> up with a resistor pack, which is a nice little part about the size of
> a deck of cards. I'll see if I can install it this evening. Many
> thanks, and I'll post the outcome.
08-22-2006, 08:32 PM
#19
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
http://www.----------.com/temp/TJresistor.pdf
God Bless America, Bill O|||||||O
mailto:--------------------
kwp wrote:
>
> Okay, I just returned from my Jeep dealer, and the parts guy hooked me
> up with a resistor pack, which is a nice little part about the size of
> a deck of cards. I'll see if I can install it this evening. Many
> thanks, and I'll post the outcome.
God Bless America, Bill O|||||||O
mailto:--------------------
kwp wrote:
>
> Okay, I just returned from my Jeep dealer, and the parts guy hooked me
> up with a resistor pack, which is a nice little part about the size of
> a deck of cards. I'll see if I can install it this evening. Many
> thanks, and I'll post the outcome.
08-22-2006, 08:32 PM
#20
Guest
Posts: n/a
Re: Correction on my earlier 2002 Wrangler post
http://www.----------.com/temp/TJresistor.pdf
God Bless America, Bill O|||||||O
mailto:--------------------
kwp wrote:
>
> Okay, I just returned from my Jeep dealer, and the parts guy hooked me
> up with a resistor pack, which is a nice little part about the size of
> a deck of cards. I'll see if I can install it this evening. Many
> thanks, and I'll post the outcome.
God Bless America, Bill O|||||||O
mailto:--------------------
kwp wrote:
>
> Okay, I just returned from my Jeep dealer, and the parts guy hooked me
> up with a resistor pack, which is a nice little part about the size of
> a deck of cards. I'll see if I can install it this evening. Many
> thanks, and I'll post the outcome.